Laserfiche WebLink
Page 3 of 8 <br /> "KI <br /> ® QUICK RESPONSE <br /> TECHNICAL DATA DRY HORIZONTAL <br /> SIDEWALL SPRINKLERS <br /> The Viking Corporation,210 N Industrial Park Drive,Hastings MI 49058 <br /> Telephone:269-945-9501 Technical Services:877-384-5464 Fax:269-818-1680 Email:techsvcs@vIkIngcorp.com <br /> vlkingcorp.com <br /> <:-':':' x*Notes A 1/2' ratchet Is required. <br /> Sprinkler Wrench Part (Not available from Viking). <br /> No. 07565W/Dxs for <br /> installing recessed - <br /> dry sprinklers. <br /> - - <br /> _I ---_ _I �___ ---■ iI r <br /> I <br /> = _ M 4_ " -_1!• II <br /> ii. i-----' I - <br /> , 1 f se <br /> lel `'.._ I I 1�1.--------- ---� <br /> Step 1. Carefully slide the Step 2: Press the wrench onto <br /> wrench sideways around the the sprinkler wrench flats and <br /> deflector and protective turn slightly to ensure engage- <br /> shield as shown. merit with the wrench flats. <br /> Figure 2: Wrench 07565WB for Adjustable Recessed Dry Horizontal Sidewall Sprinklers <br /> For 'A' Dimension. . <br /> I, Determine the distance from the face of1, -IIIIIIIIIIIIIIn1I11111111Ii,IIIIIIIIIl1IENOTE. <br /> the the to the finished face of the wall Deflector at To locate the deflector <br /> a Round to the nearest 1/2'(12.7 mm) between Finished Ceiling Distance <br /> at the minimum distance <br /> 1-1/2' (38.1 mm) and 45-112' (1,156 mm). from the wall, with no <br /> Finished Wall adjustment available, <br /> L <br /> NOTE. The deflector will extend approximatelyorder the standard dr <br /> 4-1/8' (104.8 mm) from the wall with 2' +/- 4' <102 mm) Minimum �-, horizontal sidewall sprink- <br /> 1' (25,4 mm) horizontal adjustment avakable. 6' <152 mm) Maximum* Or ler 1' <25.4 mm) shorter <br /> /� (79,4 ) than the 'A' Dimension <br /> ����\�\�� I"'1 Deflector at NDTEI <br /> `! 3-1/16' Maximum Distance To locate the deflector <br /> e <br /> I (772 mm) From Wall at the maximum distance <br /> , I IIIA I from the wall, with no <br /> .,, ..,....•;.1.. ■ l= <br /> ad,justmeat nvnllnble, <br /> / a.'-� hrder the standard dry <br /> S/8.059 pea r,= horizontal slderall sprink- <br /> Mlnimum wall opening I 1 ler I.' (25.4 mn) longer <br /> po 5-1/: than the 'A' Dimension. <br /> diameter. 1-3/4' (44.5 mm). I -Sleeve diameter' (1302 mm) <br /> Maximum wall opening 1-1/2' (38.1 mm). <br /> diameter, 2-1/4' <57 mm), 13/16' Sleeve finish matches a May be allowed up to 18' (457 mm) for certain <br /> (eab rim) finish of escutcheon FM installations. Refer to the appropriate Installation <br /> standards, Including NFPA 13 and/or FM Loss <br /> Prevention Data Sheet 2-0. <br /> Figure 3: Adjustable Standard Dry Horizontal Sidewall Sprinkler <br /> Slot <br /> Deflector — — <br /> 1 Push and Rotate Slot <br /> IAMBI . '�•_ I�I� 'i i�� 'a!► I! 'al !I1 <br /> Sleeve V �� <br /> STEP 1. Align the slot in STEP 2i Push the rounded STEP 3'Pull the escutcheon STEP 4,Push and rotate STEP g Ti, minimize <br /> the escutcheon with the end of the slot against the away from the near edge the escutcheon onto the visibility of the slot <br /> horizontal surface of near edge of the deflector, of the deflector. Move the sleeve. In the escutcheon, <br /> the deflector as shown. Push the far side of the near side of the escut- position the slot <br /> escutcheon past the deflec- cheon over the deflector. at the topof the <br /> tor, toward the sleeve. sprinkler eeve. <br /> Figure 4: Adjustable Standard Escutcheon installation <br /> Form No. F_031993 Rev 15.1 <br />