08-28-2023 Council Packet - Laserfiche WebLink

Home Browse Search

100330.1 - BRAKE, TURN, TAIL LIGHTS Two (2) Whelen M6 Series Model M6BTT 4-5/16" x 6-3/4" brake, turn, tail lights with M6FC chrome flanges shall be provided. The warning lights shall incorporate Linear Super-LED and Smart LED technology. The lighthead configuration shall consist of 18 red Super-LEDs and a clear optic polycarbonate lens. The lightheads shall be surface mountable via two screws. The lightheads shall utilize an optic collimator and a chrome vacuum metalized reflector for maximum illumination. The lighthead shall include 164 flash patterns including: a variety of CA Title 13 compliant, sinkable, left/right, top/bottom, in/out, and steady burn. The lightheads shall have the Whelen exclusive NERM (Non-Emergency Recognition Mode) feature. The lens/reflector assembly shall be wet sealed and resistant to: water, moisture, dust, and other environmental conditions. The outer lens shall have a hard coating applied to increase strength and ensure longevity. The light engine shall be installed at the rear of the unit and be completely sealed. The pc board shall be conformal coated for additional protection. The lights shall be furnished with five 6" wire pigtails, a Santoprene rubber gasket and the #M6FC chrome flanges shall be included for installation. 100331.1 - BACK-UP LIGHTS Two (2) Whelen M-Series, 4" x 6" rear LED back-up lights shall be installed. 100096.1 - TRAILER PLUG Wiring shall be provided at the rear of the apparatus for the towing of an auxiliary trailer. A 12 volt seven (7) pin electrical connector shall be wired to the chassis stop, running, and turn lights. 100067.1 - OFF ROAD LIGHTS No off road lights shall be installed. 100071.1 - GROUND LIGHTS - FRONT BUMPER Two (2) Grote #63871 LED ground lights shall be installed under the front bumper, one (1) on each side of the apparatus, wired to the Cencom, and the chassis interior lights. They shall have an aluminum housing, and be 800 lumes at 1.4 amps. 200312.1 - GROUND LIGHTS, CAB, 4 DOOR, LED STRIPS Four (4) LED ground strip lights shall be installed under the cab step area in compliance with NFPA standards, two (2) on each side of the apparatus, wired to the Cencom, and the chassis interior lights. 100183.1 - GROUND LIGHTS - UNDER REAR STEP Two (2) ground lights shall be installed under the rear step area, one on each side of the apparatus. They shall have an aluminum housing, and be 800 lumes at 1.4 amps. 100184.1 - BODY WORK LIGHTS Four (4) Grote #63871 LED body work lights with clear lens shall be installed, wired to switch on the Cencom. They shall have an aluminum housing, and be 800 lumens at 1.4 amps. Location shall be: in each corner of the protective tubing assembly to light the pump panel and the front body walkway area. 100434.1 - SCENE LIGHTS Six (6) Whelen Model M6ZC, 4" x 6" LED scene lights shall be installed. The flood-type scene lights shall be designed to direct the light 26 degrees off the mounting surface. The lights shall incorporate one (1) 35 watt halogen bulb with a clear optic polycarbonate lens for maximum illumination. Location shall be: Two (2) each side and two (2) rear of body 100107.1 - BACK-UP CAMERA SYSTEM One (1) Rear View Systems camera system shall be furnished utilizing a camera which provides a wide field of view and picture quality. A sealed camera enclosure shall be utilized along with electronic connections. The color monitor shall be installed in cab. One (1) camera shall cover the rear of the apparatus, which will activate during back-up mode and during normal operations if needed. Skeeter Brush Trucks Page 16 07/21/2023