2017 - 00589 - siding - Laserfiche WebLink

Home Browse Search

• ESR-1301 I Most Widely Accepted and Trusted Page 2 of 7 Rated Siding, Exterior Rated Siding—Sheathing is vertical or horizontal shiplap, or otherwise made intended to be installed in applications in accordance with waterproof. 2003/2006 IBC Section 2306.4.1, and 2009/2012 IBC 4.4 Component and Cladding Wind Pressure Section 2306.3. Capacity: P ty: 4.0 INSTALLATION Maximum allowable component and cladding wind loads 4.1 General: (wall, zone 5) for LP SmartSide® Precision Lap Siding and ® ® LP SmartSide® Precision Panel Siding based on a LP SmartSide® Precision Lap Siding and LP SmartSide® minimum fastener schedule, are provided in Tables 2 Precision Panel Siding must be installed in accordance through 5. Tables 2 and 3, for lap and panel siding, with the manufacturer's published installation instructions (titled Application Instructions LP SmartSide® Precision respectively, are based on full fastener penetration into the Lap LP SmartSide®Precision Panel Siding) and this report. wall studs, i.e., fastener penetration = fastener length - In the event of conflicts, this report governs. A copy of the siding thickness. Tables 4 and 5, for lap and panel siding, manufacturers installation instructions must be on the respectively, are based on a minimum fastener penetration jobsite at all times during installation. into the wall studs of 1 /z inches. LP SmartSide® Precision Lap Siding and LP SmartSide® 5.0 CONDITIONS OF USE Precision Panel Siding must be installed with an approved The LP SmartSide® Precision Lap Siding and LP water-resistive barrier as required by the applicable code. SmartSide® Precision Panel Siding described in this report Openings in, penetrations through, and terminations of the comply with, or are suitable alternatives to what is LP SmartSide® Precision Lap Siding and LP SmartSide® specified in, those codes listed in Section 1.0 of this report, Precision Panel Siding are outside the scope of this report subject to the following conditions: and must be specifically approved by the code official in 5.1 LP SmartSide Precision Lap Siding must not be accordance with the applicable code. used to satisfy the bracing requirements specified in Unless otherwise noted in this report, fasteners and the code. fastener spacing must be as noted in the applicable code. 5.2 LP SmartSide Precision Panel Siding—Sheathing, 4.2 LP SmartSide®Precision Lap Siding: when installed as set forth in this report, may be used LP SmartSide® Precision Lap Siding must be attached to as method 3 bracing specified in Section 2308.9 of framing members spaced a maximum of 16 inches the IBC and Section R602.10 of the IRC. (406 mm) on center for 3/6 category siding and a maximum 5.3 In areas where seismic analysis is required by the of 24 inches(610 mm)on center for'/16 category siding. applicable code, the applicable code requirements for ® wood structural panel shear walls must be consulted Self-aligning LP SmartSide® Precision Lap Siding is installed with nails placed at the top of the LP SmartSide® for additional detailing requirements, restrictions Precision Lap Siding, 1/2 inch (13 mm) down from the concerning certain usages, required modifications to upper edge. Each successive course of lap siding must the allowable shear loads tabulated in this report, and rest on the back rabbet and must self-align at an overlap of additional inspection requirements. 13/16 inch (21 mm). 5.4 LP SmartSide® Precision Lap Siding and LP Nails must be of sufficient length to penetrate a minimum SmartSide® Precision Panel Siding must not be of 11/2 inches (38 mm) through the sheathing and into installed in contact with concrete or masonry. framing at each stud location. 5.5 LP SmartSide® Lap Siding and LP SmartSide® 4.3 LP SmartSide®Precision Panel Siding: Precision Panel Siding must be installed with a minimum 6 inches (152 mm) of clearance from LP SmartSide® Precision Panel Siding must be installed finished grade. with its long dimension oriented vertically. 5.6 When field cuts are made to LP SmartSide®Precision When LP SmartSide® Precision Panel Siding is applied Lap Siding and LP SmartSide® Precision Panel directly to the framing, the maximum spacing of the Siding, all exposed surfaces must be finished framing must be consistent with the span rating of the LP according to the paint or caulk/sealant manufacturers' SmartSide® Precision Panel Siding, which is identified on specifications. the panel's label. 5.7 LP SmartSide® Precision Lap Siding and LP Allowable loads for shearwalls sheathed with LP SmartSide® Precision Panel Siding are manufactured SmartSide® Precision Panel Siding—Sheathing are noted by Louisiana-Pacific Corporation in Hayward, in Table 1. Wisconsin (Mill No. 357); Newberry, Michigan Four-foot-by-8-foot (1219 mm by 2438 mm) LP (Mill No. 416); Tomahawk, Wisconsin (Mill No. 435); SmartSide® Precision Panel Siding—Sheathing installed and Two Harbors, Minnesota (Mill No. 399); under a vertically, directly to framing, with a single row of nails quality control program with inspections by ICC-ES. penetrating both laps, spaced 6 inches on center at panel 6.0 EVIDENCE SUBMITTED edges and 12 inches (305 mm) on center at intermediate Data in accordance with the ICC-ES Acceptance Criteria supports may be used to satisfy the wall bracing for Treated-engineered-wood Siding (AC321), dated requirements for conventional light frame construction October 2005. specified in the code for prescriptive construction. Install per code requirements for method 3 bracing with wood 7.0 IDENTIFICATION structural panels. LP SmartSide® Precision Lap Siding and LP SmartSide® All LP SmartSide® Precision Panel Siding joints must Precision Panel Siding must be labeled with the product occur at framing members and must be protected with a designation and the name of Louisiana-Pacific Corp. The continuous wood batt, approved caulking, flashing, or stamp shall provide the following information: