1994-005102 - utility shed - Laserfiche WebLink

Home Browse Search

13.Starting at the G ,top of the back wall, install a 44 3/4"x48" piece of ROOF SHEATH- ING even with the outside edge of the 2x3 on the back wall, overlapping the ends of the 2x3 equally, and nail to the 2x3 every 6" with 6d nails. 11.Slide the prefabricated front wall into place as you did with the On the opposite back wall. Open the door and put a temporary block under it to end of the ROOF make the wall stand upright.Nail the front wall to the 2x6 FLOOR SHEATHING, STRINGERS(A)with 3-16d nails on both sides.Nail the FLOOR center the top and bottom edges on the 1 1/2" edge of the ROOF SHEATHING to the 2x6 on the front wall with 6d nails every 6" STRINGERS and nail every 6". Measure from the top of the ROOF Install 2-2x4 SIDE WALL STRINGERS(F)in the joist hangers at SHEATHING 22"and place a mark. Nail the ROOF SHEATHING to the top of the side wall and nail with 6d nails. NOTE: THE the center ROOF STRINGER with 2-6d nails on your mark.Install the FLOOR MUST BE LEVEL, OR YOU WILL HAVE TROUBLE next piece of ROOF SHEATHING on the other side of the peak.Install ALIGNING THE JOINTS IN THE SIDING.Nail the bottom edges the rest of the sheathing on the top row,alternating back and forth until of the siding on the marks that you chalked on,the FLOOR you reach the end, making sure they are centered on the ROOF STRINGERS(A)with 2-6d nails,making sure all of the joints in STRINGERS and even with the outside edge of the 2x3 on the back the side wall siding are tight.Start at the middle of the side walls wall.On the bottom row install a 313/4"x48"piece of ROOF SHEATH- and nail the top of the siding on the center of the 1 1/2"edge of ING even with the outside edge of the 2x3 on the backwall,overlapping the 2x4 SIDE WALL STRINGERS(F).Nail the top and bottom of the ends of the 2x3 equally,and nail to the 2x3 every 6"with 6d nails. the siding with 6d nails every 6".Cut 2x4421/2"side wall studs Install a 31 3/4"x48"piece of ROOF SHEATHING on the other side of from 2x4x92 5/8" PC studs (10x4, 104, & 10x8 waferboard the barn.Install the rest of the sheathing,alternating back and forth until barns&10x4 T1-11: no side wall stud needed).Place a side wall you reach the end, making sure they are centered on the ROOF stud at each joint in the siding. Install with the 31/2"side of the STRINGERS and even with the outside edge of the 2x3 on the back stud against the backside of the siding,centered over the joint in the siding.Angle nail the bottom of the side wall stud with 2-6d nails to the floor Nail the top of the side wall studs with 2-16d nails through the SIDE WALL STRINGER (F). Nail the siding to the side wall stud with 6d nails on each side of the joint every 6". Install the five ROOF STRINGERS in the joist hangers and nail with 6d nails.10x12. 10x14.& 10x16 barns:Three 2x6's will be used for the top ROOF STRINGERS (G). Notch these ROOF H I STRINGERS (G) to fit the joist hangers. CAUTION: DO NOT ATTEMPT TO SIT OR CLIMB ON THE ROOF UNTIL THE H ROOF SHEATHING IS IN PLACE AND COMPLETELY NAILED. W t N M s G 14. Nail the 1x2x47 1/2" CORNER TRIM BOARDS (H & 1) together with 3-6d nails.The widest side(H)should be placed on the front and back of the barn.Align the bottom of the CORNER TRIM BOARD(H &I)even with the bottom of the siding.Nail with 3-64 nails on each side. Always install the 1x2 trim boards with the good side exposed. 12.Cut the-waferboard sheets into ROOF SHEATHING as listed 15. Use the four 1 x2x45 1/4" FACIA for your barn size to insure the correct amount. TRIM BOARDS(J)with angles precut J ROOF SHEATHING CUT LIST: on both ends.Nail these 1 x2's with the 10x4: Cut 1-4'x8'into 2-44 3/4"x48"&cut 1-4'x8'into 2-31 3/4"x48". one end at the exact peak of the roof, 10x6: Cut 1-4X8'into 2-44 3/4"x48"&cut 1-4'x8'into 2-44 3/4"x24"& even with the TOP of the roof sheath- K cut 1-4'x8'into 2-31 3/4"x48"&2-31 3/4"x24". ing with 3-6d nails. Using one of the i ox8: Cut 24x8'into 4.44,3/4"x48"&cut 2-4'x8'into 4-31 3/4"x48". 1 x2's(K)with the angle at one end,cut 10x10: Cut 2-41x8'into 4-44 3/4"x48"&cut 1-4'x8'into 2-44 3/4"x24"& it to fit between the FACIA TRIM BOARD cut 2-4'x8'into 4-31 3/4"x48"&2-31 3/4"x24".. (J) and the CORNER BOARD (H), 14X12; Cut 3-4'xS'into 6-44 3/4"x48"&cut 2-4'x8'into 6-31 3/4"x48". making sure it is even with the TOP of H 10x14: Cut 3-4'x8'into 6-44 3/4"x48"&cut 1-4'x8'into 244 3/4"x24"& the roof sheathing and nail with 3-6d 2-31 3/4"x24"&cut 2-4'xS'into 6-31 3/4"x48". nails. 10x16: Cut 4-4'x8'into 8-44 3/41x48"&cut 3-4'x8'into 8-31 3/4"x48".