2016-00602 - alarm system - Laserfiche WebLink

Home Browse Search

PC.The PC's IP address must be set to the default range of In addition to Contact ID alarm communication, the IPDACT- the IPDACT-2/2UD such as 192.168.0.XX. 2UD version 6.0 supports upload and download to the panel 3. Windows-based configuration software (shipped with IP from anywhere on the Internet.This communication uses stan- Communicator version 6.0 or higher). Version 6.0 permits dard modem control signals wrapped up in TCP/IP packets. use of either Ethernet Crossover cable or Serial Cable. Standard programming software such as PS-Tools are used on the remote programming PC. A separate application ORDERING OPTIONS (UDPORT.exe) is started on the programming PC. This soft- IPDACT-2: IP Communicator. Includes configuration software, ware contains settings that include central station receiver IP manuals, and prepared 30"telephone cable for connection to address, port number, upload/download username and pass- panel's DACT Telco ports. word(supplied by central station).UDPORT is set to a specific IPDACT-2UD: IP Communicator with upload/download capa- communication port that will be used by the programming soft- bility (2UD modem daughter board). Includes configuration ware.The PK-PLUS program is also set to this same commu- software,manuals,and prepared 30"telephone cable for con- nicationport. The programming software must contain a to panel's DACT telco ports. subscriber number that matches the desired remote IPDACT- nection2UD card's subscriber number set at the central station. PK- 2UD: Optional modem daughter board for upgrading an PLUS "dials" the remote via standard ATDT modem corn- IPDACT 2 to an IPDACT-2UD. mands.The IPDACT-2UD v.32 modem daughter card sees the IPBRKT:Mounting bracket kit consisting of screws and battery modem commands via TCP/IP and provides a RING to the shield with standoffs. Required for mounting in lower enclo- panel. The modem on the panel handshakes with the local sure section of NFW-50, NFW2-100, SFP-5UD, and SFP- IPDACT-2UD modem and communications begin.While com- 10UD. Required for use with 411 and HP3000LX in competi- munications are limited to the panel's baud rate, the advan- tive fire panels. tage is that all communications from the remote site programming PC all the way to the remote panel are fully digi- IPENC: External mounting enclosure consisting of mounting tal and are not subject to drop outs due to phone line noise. bracket IPBRKT, and screws. Enclosure must be "close-nip- ple"to a panel.(Red;order IPENC-B for black.) Temperature and Humidity Ranges IPSPLT: Y adaptor option to allow connection of both panel dialer outputs to one cable input to IPDACT-2/2UD. This system meets NFPA requirements for operation at 0 - 49°C/32-120°F and at a relative humidity up to 93%±2%RH ALMSC-119:Serial programming cable. (non-condensing) at 32°C ± 2°C (90°F ± 3°F) However, the HP3000LX: Honeywell Power Products UL 1481-listed auxil- useful life of the electronic components may be adversely iary power supply. Enclosure must be"close-nipple"to a panel affected by extreme temperature ranges and humidity.There- via conduit. Requires IPBRKT purchased separately. fore it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of IPCHSKIT: IP Communicator Chassis Mounting Kit. For 15-27°C/60-80°F. mounting an IPDACT-2/2UD onto a CHS-4/N, CHS-4L, CHS- M3,or NFS2-640 Chassis. Agency Listings and Approvals System Architecture/Operating Theory The listings and approvals below apply to the IP Communica- tor. In some cases certain modules may not be listed by cer- The Fire Watch IP Communicators and an Ethernet connection tain approval agencies,or listings may be in process. Consult simply replace the telephone lines as the primary communica- factory for latest listing status. tions path to the central station. It connects to customer sup- plied network equipment with a gateway to the Internet. The • UL:S2424,S624 communicators provide supervised telephone line voltage to • CSFM:7300-0075:223. both panel DACT ports. Upon network communication loss, telephone line voltage is dropped to the panel and panel reports communication loss trouble.The communicators moni- tor the connectivity to both the primary and secondary receiver at the central station. Upon failure of a central station receiver the backup automatically and instantly assumes the primary role.The communicator supervises the connection to the cen- tral station at a minimum of once every 90 seconds. For a Fire or Trouble event, The Fire Alarm Panel will send Contact ID alarm event information from its DACT port. The communicator will sense the off-hook status of the panel and accept all data. The IP Communicator will then immediately packetize the Contact ID information into UDP protocol and encrypt it with 512 bits of AES encryption and send it to the central station. The central station receiver will decrypt and FireWatchTM is a trademark and Notifier® is a registered trademark of unpacketize the Contact ID information and present it to the Honeywell International Inc.HyperTerminalTM is a trademark of Hilgrave Inc. central station automation software. Upon operator acknowl- Microsoft® is a registered trademark of the Microsoft Corporation. edgement the kiss-off signal will be sent back to the panel. VisorALARM®is a registered trademark of the Teldat Corporation. ©2014 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. ISO 9001 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. C E R T F E O We cannot cover all specific applications or anticipate all requirements. ENCINEMINC 8 MURMURING All specifications are subject to change without notice. QUALITY SYSTEMS For more information,contact Notifier.Phone:(203)484-7161,FAX:(203)484-7118. www.notifier.com Page 4 of 4—DN-60408:D3•10/15/2014