2015-01498 - fire systems - Laserfiche WebLink

Home Browse Search

TFP161 Page 2 of 6 Operation DEFLECTOR 1 - Frame The glass bulb contains a fluid which 2 - Button HAT 5 4'�.G�isY.r6% expands when exposed to heat.When 3 -Sealing _ .' the rated temperature is reached, the Assembly fluid expands sufficiently to shatter the 4 - Bulb i�� ,� glass bulb,allowing the sprinkler to ac- 5 - Compression tivate and water to flow. Screw 6 - Deflector* 6* 4 2 3 1 Design 9/16' WRENCH ** Criteria (14,3 mm) FLATS NPT The TYCO Series TY-B, 5.6 K-factor, �I / Horizontal and Vertical Sidewall Sprin- `r .-�7 *HAN klers are intended for fire protection -1/O\�- / 1/ systems designed in accordance with the standard installation rules recog- ��+ nized by the applicable Listing or Ap- • prove!agency(for example,UL Listing 1-13/16• 7/16° is based on the requirements of NFPA - (46,0 mm) (11,1 mm) 13, and FM Approval is based on the NOMINAL requirements of the FM Loss Preven- CENTERLINE MAKE-IN tion Data Sheets). Only the Style 10 OF SPRINKLER WATERWAY Recessed Escutcheon, as applicable, 1-1/2" is to be used for recessed horizontal x(38,1 mm)y installations. *Temperature rating is indicated on - 2-3/16' - Installation Deflector. (55,6 mm) ESCUTCHEON The TYCO Series TY-B, 5.6 K-factor, ** Pipe thread I STYLE 10 — I PLATE SEATING Horizontal and Vertical Sidewall Sprin- connections per RECESSED SURFACE klers must be installed in accordance ISO 7-1 can be ESCUTCHEON with this section. provided on special request. General Instructions ��1� Do not install any bulb type sprinkler 2-7/8'DIA. II►�__ if the bulb is cracked or there is a loss (73,0 mm) �,, I IIIIIIIIII I of liquid from the bulb.With the sprn- 3 •� 1 1 kler held horizontally,a small air bubble E should be present.The diameter of the air bubble is approximately 1/16 inch (1,6 mm)for the 135°F(57°C)to 3/32 inch(2,4 mm)for the 360°F(182°C)tem- perature ratings. FIGURE 1 A leak-tight 1/2 inch NPT sprinkler joint SERIES TY-B HORIZONTAL SIDEWALL(TY3351)SPRINKLER should be obtained by applying a min- 5.6 K-FACTOR STANDARD RESPONSE imum-to-maximum torque of 7 to 14 ft.-lbs. (9,5 to 19,0 Nm). Higher levels ceiling.The word"TOP"on the Deflec- Vertical Sidewall Sprinkler of torque may distort the sprinkler inlet tor is to face towards the ceiling. Installation and cause leakage or impairment of the The Series TY-13 Vertical Sidewall Sprin- sprinkler. Step A. After installing the Style 10 klers must be installed in accordance Do not attempt to make-up for insuf- Mounting Plate over the sprinkler with the following instructions. ficient adjustment in the escutcheon threads,hand-tighten the sprinkler into the sprinkler fitting. Install vertical sidewall sprinklers in the plate by under-or over-tightening the sprinkler. Readjust the position of the Step B.Tighten the sprinkler into the pendent or upright position with the ar- sprinkler fitting to suit. sprinkler fitting using only the W-Type 7 row on the Deflector pointing away from Recessed Sprinkler Wrench(Ref.Figure the wall. Horizontal Sidewall Sprinkler 5).Apply the W-Type 7 Recessed Sprin- Step 1.With pipe thread sealant applied Installation kler Wrench to the sprinkler wrench flats to the pipe threads, hand-tighten the The TYCO Series TY-B Recessed Hori- (Ref.Figure 1). sprinkler into the sprinkler fitting. zontal Sidewall Sprinklers must be in- stalled in accordance with the following Step C.After the ceiling is installed or Step 2. Tighten the sprinkler into the instructions. the finish coat is applied, slide on the sprinkler fitting using only the W-Type Install recessed horizontal sidewall Style 10 Closure over the Series TY-B 6 Sprinkler Wrench(Ref.Figure 4). For Sprinkler and push the Closure over the wax-coated sprinklers, use an 8 or 10 sprinklers in the horizontal position with Mounting Plate until its flange comes in inch adjustable Crescent wrench.Apply the centerline of waterway perpendicu- contact with the ceiling. the W-Type 6 Sprinkler Wrench or the lar to the back wall and parallel to the Crescent wrench,as applicable,to the wrench flats(Ref.Figure 2).