2014-00683 - alarm system - Laserfiche WebLink

Home Browse Search

FMM-101(A) Mini Monitor Module Dimensions: 1.3° (3.302 cm) high x 2.75° (6.985 cm)wide x • Built-in type identification automatically identifies this device 0.65°(1.651 cm)deep. as a monitor module to the panel. Wire length:6•(15.24 cm)minimum. • Powered directly by two-wire SLC loop.No additional power required. FZM4(A) Interface Module • High noise(EMF/RFI)immunity. • Supports compatible two-wire smoke detectors. • Tinned,stripped leads for ease of wiring. • Supervises IDC wiring and connection of external power • Direct-dial entry of address:01 —159 on FlashScan loops; source. 01—99 on CLIP loops. • High noise(EMF/RFI)immunity. • SEMS screws with clamping plates for ease of wiring. 3 1415 0 1 ADDRESS 0 1 • Direct-dial entry of address:01 —159 on FlashScan loops, 13 2 2 01 —99 on CLIP loops. 12 O 3 LOOP O 3 • LED flashes during normal operation;this is a programma- 11 4 4 ble option. • LED latches steady to indicate alarm on command from 10 g 8 7 6 5 9 8 7 6 control panel. TENS ONES The FZM-1(A) Interface Module is intended for use in intelli- gent, addressable systems, where the individual address of each module is selected using built-in rotary switches. This module allows intelligent panels to interface and monitor two- wire conventional smoke detectors.It transmits the status(nor- mal,open,or alarm)of one full zone of conventional detectors 0p back to the control panel. All two-wire detectors being moni- tored must be UL compatible with the module. The FZM-1(A) can be used to replace MMX-2(A) modules in existing sys- tems. FZM-1(A) APPLICATIONS The FMM-101(A) Mini Monitor Module can be installed in a Use the FZM-1(A)to monitor a zone of two-wire smoke detec- single-gang junction directly behind the monitored unit. Its tors.The monitored circuit may be wired as an NFPA Style B small size and light weight allow it to be installed without rigid (Class B)or Style D(Class A)Initiating Device Circuit.A 3.9 K mounting. The FMM-101(A) is intended for use in intelligent, ohm End-of-Line Resistor(provided)terminates the end of the two-wire systems where the individual address of each module Style B or D (class B or A) circuit(maximum IDC loop resis- is selected using rotary switches. It provides a two-wire initiat- tance is 25 ohms). Install ELR across terminals 8 and 9 for ing device circuit for normally-open-contact fire alarm and Style D application. security devices. The FMM-101(A) can be used to replace MMX-101(A)modules in existing systems. FZM-1(A)OPERATION FMM-101(A)APPLICATIONS Each FZM-1(A) uses one of the available module addresses on an SLC loop. It responds to regular polis from the control Use to monitor a single device or a zone of four-wire smoke panel and reports its type and the status(open/normaVshort) detectors,manual fire alarm pull stations,waterflow devices,or of its Initiating Device Circuit(IDC). A flashing LED indicates other normally-open dry-contact devices. May also be used to that the module is in communication with the control panel. monitor normally-open supervisory devices with special super- The LED latches steady on alarm (subject to current limita- visory indication at the control panel. Monitored circuit/device tions on the loop). is wired as an NFPA Style B(Class B)Initiating Device Circuit. A 47K ohm End-of-Line Resistor(provided)terminates the cir- FZM-1(A)SPECIFICATIONS cuit. Nominal operating voltage:15 to 32 VDC. FMM-101(A)OPERATION Maximum current draw:5.1 mA(LED on). Each FMM-101(A) uses one of the available module Maximum IDC wiring resistance:25 ohms. addresses on an SLC loop. It responds to regular polls from Average operating current:300 NA, 1 communication and 1 the control panel and reports its type and the status(open/nor- LED flash every 5 seconds,3.9k sol. mal/short)of its Initiating Device Circuit(IDC). EOL resistance:3.9K ohms. FMM-101(A) SPECIFICATIONS External supply voltage (between Terminals T3 and T4): Nominal operating voltage:15 to 32 VDC. DC voltage: 24 volts power limited. Ripple voltage: 0.1 Vrms Average operating current:350 NA, 1 communication every maximum.Current:90 mA per module maximum. 5 seconds, 47k EOL; 600 pA Max. (Communicating, IDC Temperature range:32°F to 120°F(0°C to 490C). Shorted). Humidity range:10%to 93%noncondensing. Maximum IDC wiring resistance:40 ohms. Dimensions: 4.5• (11.43 cm) high x 4• (10.16 cm) wide x Maximum IDC Voltage: 11 Volts. 1.25° (3.175 cm) deep. Mounts to a 4° (10.16 cm) square x Maximum IDC Current:400 NA. 2.125°(5.398 cm)deep box. EOL resistance:47K ohms. Temperature range:32°F to 120°F(0°C to 490C). Humidity range: 10%to 93%noncondensing. Page 2 of 4—DN-6720:C•10/06/2010