2014-00683 - alarm system - Laserfiche WebLink

Home Browse Search

DN-6720:C•H-220 FMM-1 (A), FMM4 01 (A), ° FZM4 (A) & NOTIFIER FDM-1 (A) �� (Monitor Modules with FlashScan by H o n eywe l l IntelligenVAddressable Devices General Four different monitor modules are available for Notifiers intel- ligent control panels for a variety of applications.Monitor mod- ules supervise a circuit of dry-contact input devices, such as conventional heat detectors and pull stations, or monitor and power a circuit of two-wire smoke detectors(FZM-1(A)). FMM-1(A)is a standard-sized module(typically mounts to a 4° [10.16 cm]square box)that supervises either a Style D(Class A) or Style B(Class B)circuit of dry-contact input devices. FMM-101(A)is a miniature monitor module a mere 1.3"(3.302 cm) H x 2.75° (6.985 cm) W x 0.5° (1.270 cm) D that super- vises a Style B (Class B) circuit of dry-contact input devices. Its compact design allows the FMM-101(A)to be mounted in a �° single-gang box behind the device it monitors. t, FZM-1(A)is a standard-sized module that monitors and super- •°^+. • �•° $ vises compatible two-wire,24 volt,smoke detectors on a Style s D(Class A) or Style B(Class B)circuit. FDM-1(A)is a standard-sized dual monitor module that moni- tors and supervises two independent two-wire Style B (Class B)dry-contact initiating device circuits(IDCs)at two separate, FMM-1(A)(Type H) consecutive addresses in intelligent,two-wire systems. FlashScan®(U.S. Patent 5,539,389) is a communication pro- A) Initiating Device Circuit. A 47K ohm End-of-Line Resistor tocol developed by NOTIFIER that greatly increases the speed (provided) terminates the Style B circuit. No resistor is of communication between analog intelligent devices. Intelli- required for supervision of the Style D circuit. gent devices communicate in a grouped fashion. If one of the FMM-1(A) OPERATION devices within the group has new information,the panel CPU stops the group poll and concentrates on single points. The Each FMM-1(A) uses one of the available module addresses net effect is response speed greater than five times that of on an SLC loop. It responds to regular polis from the control other designs. panel and reports its type and the status(open/normal/short) of its Initiating Device Circuit(IDC). A flashing LED indicates FMM-1(A) Monitor Module that the module is in communication with the control panel. The LED latches steady on alarm (subject to current limita- • Built-in type identification automatically identifies this device tions on the loop). as a monitor module to the control panel. • Powered directly by two-wire SLC loop.No additional power FMM-1(A) SPECIFICATIONS required. Nominal operating voltage:15 to 32 VDC. • High noise(EMF/RFI)immunity. Maximum current draw:5.0 mA(LED on). • SEMS screws with clamping plates for ease of wiring. Average operating current: 350 pA (LED flashing), 1 com- • Direct-dial entry of address:01 —159 on FlashScan loops; munication every 5 seconds,47k EOL. 01—99 on CLIP loops. Maximum IDC wiring resistance:40 ohms. • LED flashes green during normal operation (this is a pro- EOL resistance:47K ohms. grammable option) and latches on steady red to indicate alarm. Temperature range:32°F to 120°F(0°C to 490C). The FMM-1(A) Monitor Module is intended for use in intelli- Humidity range: 10%to 93%noncondensing. gent,two-wire systems, where the individual address of each Dimensions: 4.5° (11.43 cm) high x 4° (10.16 cm) wide x module is selected using the built-in rotary switches. It pro- 1.25" (3.175 cm) deep. Mounts to a 4° (10.16 cm) square x vides either a two-wire or four-wire fault-tolerant Initiating 2.125'(5.398 cm)deep box. Device Circuit(IDC)for normally-open-contact fire alarm and supervisory devices.The module has a panel-controlled LED indicator. The FMM-1(A) can be used to replace MMX-1(A) modules in existing systems. FMM-1(A)APPLICATIONS Use to monitor a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally- open dry-contact alarm activation devices. May also be used to monitor normally-open supervisory devices with special supervisory indication at the control panel. Monitored circuit may be wired as an NFPA Style B(Class B)or Style D(Class DN-6720:C•10/06/2010—Page 1 of 4