2014-00683 - alarm system - Laserfiche WebLink

Home Browse Search

• Maximum current charge: 1.5 A. Standards and Codes • Maximum battery capacity: 18 AH. The FCPS-2456 and FCPS-24S8 comply with the following standards: Applications • NFPA 72 National Fire Alarm Code. Example 1:Expand notification appliance power an additional . UL 864 Standard for Control Units for Fire Alarm Systems 6.0 A (FCPS-2456) or 8.0 A (FCPS-24S8). Use up to four (NAC expander mode). Class B (Style Y) outputs or four Class A (Style Z) outputs . UL 1481 Power Supplies for Fire Alarm Systems. (using ZNAC-4). For example,the FACP notification appliance circuits will activate the FCPS when reverse-polarity activation occurs. Trouble conditions on the FCPS are sensed by the Agency Listings and Approvals FACP through the notification appliance circuit. These listings and approvals apply to the modules specified in Example 2: Use the FCPS to expand auxiliary regulated 24- this document.In some cases,certain modules or applications volt system power up to 4.0 A (FCPS-24S6) or up to 6.0 A may not be listed by certain approval agencies, or listing may (FCPS-24S8). Both resettable and non-resettable power be in process.Consult factory for latest listing status. options are available. Resettable outputs are created by con- UL Listed: S635,S674 necting the resettable output from the FACP to one or both of ULC Listed:S635(FCPS-24S6C&FCPS-24S8C) the FCPS inputs. Example 3: Use addressable control modules to activate the CSFM Approved: 7315-0028:225 FCPS instead of activating it through the FACP notification MEA: 299-02-E appliance circuits.This typically allows for mounting the FCPS FM Approved at greater distances' away from the FACP while expanding system architecture in various applications. Ordering Information For example, an addressable control module is used to acti- FCPS-2456. 6.0 A, 120 VAC remote charger power supply vate the FCPS,and an addressable monitor module is used to Includes main printed circuit board, transformers, enclosure sense FCPS trouble conditions. Local auxiliary power output (15"H x 14.5'W x 2.75"D[cm:38.1 H x 36.83W x 6.985D]),and from the FCPS provides power to the addressable control installation instructions. module. FCPS-24S6C: Same as above,ULC-listed. `NOTE:Addressable FACPs are capable of locating control and monitor modules at distances of up to 12,500 feet(3,810 meters). FCPS-24S6R: Same as FCPS-24S6 with red enclosure. FCPS-24S6E: 6.0 A,240 VAC remote charger power supply. Sync Follower/Generator Note Includes main printed circuit board, transformers, enclosure In some installations, it is necessary to synchronize the flash (15"H x 14.5'W x 2.76'D[cm:38.1 H x 36.83W x 6.985D]),and timing of all strobes in the system for ADA compliance. installation instructions. Strobes accomplish this by monitoring very short timing pulses FCPS-2458: 8.0 A, 120 VAC remote charger power supply on the NAC power which are created by the FACP. When Includes main printed circuit board, transformers, enclosure installed at the end of a NAC wire run,the FCPS-24S6/-2458 (15"H x 14.6W x 2.76'D[cm:38.1 H x 36.83W x 6.985D]),and can track (i.e. "follow") the strobe synchronization timing installation instructions. pulses on the existing NAC wire run.This maintains the overall FCPS-24S8C Same as above,ULC-listed. system flash timing of the additional strobes attaches to the FCPS. FCPS-24SSR: Same as FCPS-2458 with red enclosure. When the FCPS-24S6/-24S8 is configured(via DIP switch set- FCPS-24S8E: 8.0 A,240 VAC remote charger power supply. tings)as a"sync follower;'the FCPS's NAC outputs track the Includes main printed circuit board, transformers, enclosure strobe synchronization pulses present at the FCPS's sync (15"H x 14.5'W x 2.76'D[cm:38.1 H x 36.83W x 6.985D]),and input terminal.The pulses originate from an upstream FACP or installation instructions. other power supply. ZNAC-4: Class A(Style Y)NAC option module. When the FCPS-2456/-24S8 are configured (via DIP switch EOLR-1: 12/24 VDC end-of-line relay for monitoring four-wire settings) as a"sync generator,"the FCPS's sync input termi- smoke detector power. nals are not used. Rather, the FCPS is the originator of the BAT-1270: Battery, 12-volt, 7.0 AH (two required, see BAT strobe synchronization pulses on the FCPS's NAC outputs. In Series data sheet DN-6933). "sync generator"mode,the sync type(System Sensor,Whee- lock,or Gentex)is selectable via DIP switch settings. PS-1270: Battery, 12-volt, 7.0 AH (two required, see PS Series data sheet DN-1109) System Sensor®and NOTIFIER®are registered trademarks of Honeywell International Inc. ©2009 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. 'SO 9oo1 We try to keep our product information up-to-date and accurate. _ We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. F9 QUALITY SYSTEMS Made in the U.S.A. For more information,contact Notifier.Phone:(203)4847161,FAX:(203)4847118. www.nofrfier.com Page 2 of 2—dn-6927:a•04/30/09