2014-00683 - alarm system - Laserfiche WebLink

Home Browse Search

dn-6927:a FCPS-24S6(C/E)A FCPS- (24,Ss C/E) �J NOTIFIER (6- & B-Amp 24-volt by Honeywell (Remote Power Su lies Power General The FCPS-24S6E (6-amp) and FCPS-24S8E (8-amp) are remote power supplies with battery charger.The FCPS-24S6/- 24S8 may be connected to any 12 or 24 volt fire alarm control panel (FACP) or may be used as stand-alone supplies. Pri- mary applications include notification appliance (bell) circuit (NAC)expansion(to support ADA requirements and NAC syn- chronization) or auxiliary power to support 24 volt system accessories. The FCPS-24S6/-2458 provides regulated and filtered 24 VDC power to four notification appliance circuits configured as either four Class B(Style Y)or Class A(Style Z, = _with ZNAC-4 option module).Alternately,the four outputs may be configured as all non-resettable,all resettable or two non- r ry• resettable and two resettable. The FCPS-24S6/-2458 also contains a battery charger capable of charging up to 18 AH batteries.FCPS-24S6C&FCPS-24S8C are ULC-listed. NOTE. Unless otherwise specified, the terms FCPS-24S6 and FCPS-24S8 used in this document refers to the standard FCPS- 2456 and FCPS-2458, FCPS-24S6C and FCPS-24S8C, the FCPS-24S6E and FCPS-24S8E vngmt.� Features • Includes integral battery charger capable of charging up to • UL-Listed NAC synchronization using System Sensor, 18 AH batteries.Cabinet capable of housing 7.0 AH batter- Wheelock,or Gentex"Commander2"appliances. ies. • Operates as a "sync-follower' or as a "sync-generator" • Battery charger may be disabled via DIP switch for applica- (default). See note on page 2. tions requiring larger batteries. • Contains two fully-isolated input/control circuits -triggered • Fixed, clamp-type terminal blocks accommodate up to 12 from FACP NAC(NAC expander mode)or jumped perma- AWG(3.1 mm2)wire. nently"ON"(stand-alone mode). • Four Class B (Style Y) or four Class A (Style Z, with Specifications ZNAC-4 module)NACs. Primary(AC)Power: • 6-amp (FCPS-2456) or 8-amp (FCPS-24S8) full load out- put,with 3 amps maximum/circuit, in NAC expander mode • FCPS-24S6C/-24S8C: 120 VAC,60 Hz,3.2A maximum. (UL 864). • FCPS-24S6E/-24S8E: 240 VAC,50 Hz, 1.6A maximum. • 4-amp (FCPS-24S6) or 6-amp (FCPS-24S8) continuous • Wire Size: minimum#14 AWG(2.Omm2)with 600 V insula- output in stand-alone mode(UL 1481). tion. • Compatible with coded inputs;signals passed through. Control Input Circuit: • Optional power-supervision relay(EOLR-1). • Trigger input Voltage: 9 to 32 VDC. • In stand-alone mode, output power circuits may be config- • Trigger Current: 2.0 mA(16-32 V); Per Input: 1.0 mA(9 ured as: resettable, (reset line from FACP required), -16 V). non-resettable,or a mix of two and two. Trouble Contact Rating: 5 A at 24 VDC. • Fully regulated and filtered power output-optimal for pow- Auxiliary Power Output: Specific application power 500 mA ering four-wire smoke detectors, annunciators, and other system peripherals requiring regulated/filtered power. maximum. • Power-limiting technology meets UL power-limiting require- Output Circuits: ments. • +24 VDC filtered,regulated. • Form-C normally-closed trouble relay. • 3.0 A maximum for any one circuit. • Fully supervised power supply,battery,and NACs. • Total continuous current for all outputs(stand-alone mode): • Selectable earth fault detection. —FCPS-24S6: 4.0 A maximum. • AC trouble report selectable for immediate 2-hour delay. —FCPS-2458: 6.0 A maximum. • Works with virtually any UL 864 fire alarm control which uti- • Total short-term current for all outputs(NAC expander mode): lizes an industry-standard reverse-polarity notification cir- —FCPS-24S6: 6.0 A maximum. cuit(including unfiltered and unregulated bell power). —FCPS-24S8: 8.0 A maximum. • Requires input trigger voltage of 9-32 VDC. Secondary Power(Battery)Charging Circuit: • Self-contained in compact, locking cabinet-15"H x 14.5"W x 2.75"D(cm:38.1 H x 36.83W x 6.985D). • Supports lead-acid batteries only. • Float-charge voltage: 27.6 VDC. dn-6927:a•04/30/09—Page 1 of 2