2014-01148 - alarm system - Laserfiche WebLink

Home Browse Search

+ � l � . ' . . . - Duct Sensor Location Considerations: l. Proper duct smoke detection location must ensure ' /Exhaust Damper senso�oK adequate airflow within the duct housing. � 2. Duct air velocity rating is 300 to 4000 ft/min(91 to Exnaust•- ' �Retum Air 1220 m/min).Pressure differential between intake ' and exhaust tubes is required to be between 0.015 to 0o not iocate; 1.55 inches of water(0.381 to 39.37 mm). se�sor nere � 3. Ensure accessibility for test and service. Rda per r � 4. Proper Locations:downstream side of filters to detect fires in the filters;in return ducts,ahead of mixing ; areas;upstream of air humidifier and cooling coil. 5. Other locations and orientations may be required for Fresh air—► ;�—►Supply Air proper duct smoke detection depending on duct access,system design,and duct airflow testing. o,noc�ocate Filter bank sensor otc Contact your local Simplex product supplier for sensor here 3SSiSt3IICC. Locations to Avoid: Additional lnformation.Refer to NFPA 90A,Standard 1. Where dampers closed for comfort control would for the Installation of.4ir Conditioning and Yentilating interfere with airflow. Systems;NFPA 72,the National Fire Alarm and Signaling 2, Next to outside air inlets(unless the intent is ta Code;and the NEMA Guide for Proper Use of Smoke monitor smoke entry from that area). Detectors in Duct Applications,and Installarion Instrucrions 3. In retum air damper branch ducts and mixing areas 574-776. where airflow may be restricted. . - . . Generaf Mechanica{and Environmental Air Velocity Range(tinear ff/min) 300 to 4000 ft/min(91 to 1220 mlmin) Sensor Sensitivity Range 0.2%to 3.7°k per foot of obscuration,selectable at hast control panel UL Listed Temperature Range 32°F to 100°F(0°C to 38°C) � Operating Temperature Range 32°F to 122°F(0°C to 50°C) Storage Temperature Range 0°F to 140°F(-78°C to 60°C) . Humidity Range 10%to 95%RH,non-condensing Wiring Connections Terminal blocks,18 to 12 AWG(0.82 mmz to 3.31 mm2) Housing Color Black base with clear cover Remote StatuslAlarm LED and Test Station with Remate Status/Alarm LED Remote Alarm LED Current 1.2 mA,no impact to 24 VDC alarm current(2098-9808 or 2098-9806) Test Station Keyswitch Curcent 3.3 mA,no impact to 24 VDC alarm current(2098-9806} Remote Alarm LED and Test Station Distance 250 ft(76 m)maximum Addressable Operation Data Communications IDNet or MAPNET 11 communications,autaselect,one address per housing; provides operating power to mode14098-9755 Model 4098-9756 with Supervised Multiple Relay Control,Requires Separate Fused 24 VDC from Fire Atarm Power Supply lnput Voltage 1&32 VDC(24 VDC nomina!) Standby Current 3 mA @ 24 VDC Alarm Current 15 mA @ 24 VDC;add 15 mA for each 409&9843 relay For use with 409&9843 relay only,quantity of 15 maximum;distance of 500 ft Supervised Remote Relay Control Output (152 m)maximum;requires 4081-9008(ref.733-894)10 ki2, 1/2 W end-of-line resistor 4098-9843 Relay Output Ratings,Single Form C,use with Modet 4Q9&9756 Only Coil Current 15 mA @ 24 VDC,up to t5 maximum per relay control oufput Relay Contacts 7 A at 0.35 PF @ 28 VDC&120 VAC;250µA @ 5 VDC Location Distance 500 ft(152 m)maximum to relay coils;locate relays within 3 ft(1 m)of device being controlled per NFPA 72 TYCO,SJMPLEX,and the product names listed in tlds materia!are marks and/or registered mrrrLa�.Unauthorized rere is srricHy prohibited..NFPA 72 and 7Jatinnaf Fve A(arm and Signa/ing Corle are registered trademarl�of the National Fire Protection Association(IJFPA): ��S i m p I Ex Tyco Fire Profection Products• Westminster,MA•01441-0001•USA 54098-0030-9 11 t2012 www.simplexgrinnelLcom O 2012 Tyw F'ue Prvtec7ion Products.All rightr resernd AUspecificaiinns wtd ather injormation shoxm xrre avrent as afdaument rnvision dat¢m�d m�e suhject ta chanbse wrthout notice. .