2013 - 00685 - septic - Laserfiche WebLink

Home Browse Search

4. MOUND SIZING A. Calculate Clean Sand Lift: 3 feet minus Depth to Limiting Condition (1.C) = Clean Sand Lift (1 ft minimum) 3.0 ft - 2.3 ft = 1.0 ft Design Sand Lift (optional): B. Calculate Upslope Height: Clean Sand Lift (4.A) +media depth (1 ft.) +cover (1 ft.) = Upslope Height 1.0 ft + 1.0 ft + 1.0 ft= 3.0 ft D-14:Slope Multiplier Table Land Slope% 0 ! 2 3 4 5 6 7 8 9 IO 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 IlpsIope 3:1 3.00 2.91 2.83 2.75 2.68 2.61 2.54 2.44 2.42 2.36 2.31 2.26 2.21 2.17 2.13 2.09 2.05 2.03 2.00 1.97 1.95 1.93 1.91 1.89 1.87 1.85 Beim Ratio 4:1 4.00 3.85 3.70 3,57 3.45 3.33 3.23 3.12 3.0312.94 2.86 2.78 2.70 2.62 2.55 2.4 2.41 2.35 2.29 2.23 2.18 2.13 2.08 2.03 1.98 1.93 Land Slope% 0 1 2 3 4 5 6 7 8 1 9 10 11 12 13 14 4 15 16 17 1 18 19 20 21 22 23 24 25 Downslope 3:1 3.00 3,09 3.19 3.30 3.41 3.53 3.66 3.813 3.55 4.11 4.29 4.48 4.69 4.95 5.24.5.55 5.88 6.24 1 6.63 7.04 7.47 7.93 8.42 8.93 9.46 10.02 BeimRatio �4:1 4.00 4.17 4.35 4.54 4.76 5.00 5.26 5.56 5.88 6.25 6.67 7.14 7.6918.29 8.92 9.57 10.24 10.94111.67 12.42 13.19 13.99 14.82 15.67 16.54 17.44 Select Upslope Berm Multiplier C. (based on land slope): 3.45 (figure D-34) D. Calculate Upslope Berm Width: Multiplier (4.C)X Upslope Mound Height (4.5) = Upslope Berm Width 3.45 ft x 3.0 ft = 10.4 ft E. Calculate Drop in Elevation Under Bed: Bed Width (2.B) X Land Slope (1.D) : 100=Drop (ft) 10.0 ft x 4.0 % : 100= 0.40 ft F. Calculate Downslope Mound Height: Upslope Height (4.B) +Drop in Elevation (4.E) =Downslope Height 3.0 ft + 0.40 ft = 3.4 ft G Select Downslope Berm Multiplier (based on land slope): 4.76 (figure D-34) H. Calculate Downslope Berm Width:Multiplier (4.G)X Downslope Height (4.F)=Downslope Berm Width 4.76 x 3.4 ft = 16.2 ft I. Calculate Minimum Berm to Cover Absorption Area: Downslope Absorption Width (3.B or 3.C) +4 ft. =ft 10.0 ft + 4 ft = 14.0 ft J. Design Downslope Berm =greater of 4H and 41: 16.2 ft K. Select Endslope Berm Multiplier: 3.00 (usually 3.0 or 4.0) L. Calculate Endslope Berm (4.K)X Downslope Mound Height (4.F)=Endslope Berm Width 3.00 ft x 3.4 ft = 10.2 ft M. Calculate Mound Width: Upslope Berm Width(4.D) +Bed Width (2.B) +Downslope Berm Width (4.J)=ft 10.4 ft + 10.0 ft + 16.2 ft = 36.5 ft N. Calculate Mound Length: Endslope Berm Width (4.L) +Bed Length (2.C) +Endslope Berm Width (4.L) =ft 10.2 ft + 63.0 ft + 10.2 ft = 83.4 ft 0. If using a registered product, enter the Component Length: in. : 12 ft. P. If using a registered product, enter the Component Width: in. : 12 ft. Q. Number of Components per Row =Bed Length (2.C) divided by Component Length (4.0) (Round up) 63 = R. Number of Rows =Bed Width (2.B)divided by Component Width (4.P) (Round up) Adjust Contour Loading Rate on Design Summary page until this number is a whole number S. Total Number of Components =Number of Components per Row X Number of Rows X =