Laserfiche WebLink
• APPLICATION INSTRUCTIONS (CONT.) <br /> KICK-OUT FLASHING FINISHING INSTRUCTIONS <br /> •Install kick-out flashing to direct the water into the gutter DO <br /> • Prime and paint all exposed surfaces including all drip edges <br /> •Install step flashing with minimum 4-inch upper leg or where water will hang. <br /> • Apply finish coat as soon as possible or within 180 days <br /> •Properly integrate flashing with the secondary water-resistive of application. <br /> barrier. Use housewrap,flashing tape,z-flashing,or other items • High-quality acrylic latex paint,specially formulated for <br /> as needed to maintain the counterflashing principle. use on wood and engineered wood substrates,is highly <br /> recommended.Semi-gloss or satin finish oil or alkyd paints are <br /> •DO NOT extend the siding or trim into the kick-out flashing or gutter acceptable.For flat alkyd paint,please check with the coating <br /> manufacturer for their recommendations for use on composite <br /> •Maintain a clearance between the end of the gutter and the adjoining wood siding. <br /> wall to allow for proper maintenance of the siding • Follow the coating manufacturer's application and <br /> maintenance instructions. <br /> •Paint ALL exposed cut edges <br /> DO NOT USE <br /> • Semi-transparent and transparent stains. <br /> • Shake and shingle paints. <br /> \ • Vinyl-based resin formulas such as vinyl acetate, PVA, <br /> LP Sidin vinyl acetate/acrylic copolymer paints. <br /> B <br /> �` ® Minimum 1"clearance <br /> between trim and roofing NAILING INSTRUCTIONS <br /> Air • LP SmartSide 76 Series lap siding may be attached directly to fram- <br /> / ing members spaced up to a maximum of 24 in.on center.76 Series <br /> LP SmartSide Lap may also be applied over code-approved nailable <br /> rai <br /> sheathing. <br /> �� • LP SmartSide 38 Series lap siding may be attached over nailable <br /> G <br /> sheathing or directly to framing members that are spaced up to a <br /> maximum of 16 in.on center. <br /> ' <br /> Ar/ <br /> / ,1 ,I / —� —AV • Check your local building code before starting to install the Product <br /> di <br /> p. V / Clean rain to confirm if sheathing is needed. <br /> T I gutter • Siding joints should be staggered over successive courses. <br /> , For installation with or without nailable sheathing,joints must occur <br /> over stud locations. <br /> Do not run trim or siding inside • Siding shall be installed with top(blind)nailing,with the nails placed <br /> of the kick out flashing a minimum of 3/8 in.from either end and a minimum of 3/4 in.from <br /> the top edge of the board.Siding may only be face nailed as required <br /> immediately below window sills,frieze boards,and horizontal trim <br /> bands. <br /> • Overlap successive courses of siding a minimum of 1 in. <br /> TRIM • Use minimum 8d(0.113 in.shank diameter),corrosion resistant,box style <br /> nails. <br /> Trim should be thick enough so the siding does not extend be- <br /> yond the face of the trim. • All exposed face nails must be caulked and sealed in a manner that <br /> prevents moisture intrusion and water buildup. <br /> •Trim and fascia must be applied in a manner that will not allow • Fasteners at each stud location must penetrate solid wood framing <br /> moisture intrusion or water buildup. or the sheathing and wood framing a minimum of 1.5 in. <br /> •LP®SmartSide®siding is not designed and/or manufactured to CONDITION CORRECTION <br /> be used as trim or fascia.LP SmartSide trim and fascia are avail- Snug /Eh OK 41k <br /> able in a variety of dimensions. .l, Ul► <br /> Flush 'UI, OK "UI' <br /> Visible fiber 0:Paint�� ���� <br /> Countersunk1/16 in.-1/8 in.- 0111P'1 Seal Seal with caulking— 0+V� <br /> Countersunk more f►ri' Seal with caulk 9114 <br /> than 1/8 in. and renail <br />