2006-P00174 - alarm system - Laserfiche WebLink

Home Browse Search

MMF-301(A) Mini,Monitor'Module Dimensions: 1.3'(3.302 cm)high x 2.75" (6.985 cm)wide x • Built-in type Identification automatically identifies this device0.65'(1.651 cm)deep. as a monitor module to the panel. Wire length:6'(15.24 cm)minimum. • Powered directly by two-wire SLC loop.No additional power required. MMF-302(A) Interface Module • High noise(EMF/RFI)Immunity. • Supports compatible two-wire smoke detectors. • Tinned,stripped leads for ease of wiring. • Supervises IDC wiring and connection of external power • Direct-dial entry of address:01 —159 on MS-9600 series source. panels,01—99 on other compatible systems • High noise(EMF/RFI)immunity. a • SEMS screws with clamping plates for ease of wiring. 1415 0 1 0 1 • Direct-dial entry of address: 01 —159 on MS-9600 series s S. . 2 2 panels,01 —99 on other compatible systems. - LED flashes during normal operation. 14 O 4 • LED latches steady to indicate alarm on command from 9 6 5 control panel. TENS ONES The MMF-302(A)Interface Module is intended for use in intelli- gent, addressable systems, where the individual address of each module is selected using built-in rotary switches. This module allows intelligent panels to interface and monitor two- wire conventional smoke detectors.It transmits the status(nor- 0 O _= U mal,open,or alarm)of one full zone of conventional detectors W ' Q back to the control panel. All two-wire detectors being moni- } " m tored must be UL compatible with the module. The MMF- 302(A) can be used to replace M302(A) modules in existing systems. MMF-302(A)APPLICATIONS Use the MMF-302(A) to monitor a zone of two-wire smoke The MMF-301(A) Mini Monitor Module can be installed in a detectors. The monitored circuit may be wired as an NFPA single-gang junction directly behind the monitored unit. Its Style B(Class B)or Style D(Class A)Initiating Device Circuit. small size and light weight allow it to be installed without rigid A 3.9 K ohm End-of-Line Resistor(provided) terminates the mounting. The MMF-301(A) is intended for use in intelligent, end of the Style B or D (class B or A)circuit(maximum IDC two-wire systems where the individual address of each module loop resistance is 25 ohms). Install ELR across terminals 8 is selected using rotary switches. It provides a two-wire initiat- and 9 for Style D application. ing device circuit for normally-open-contact fire alarm devices. The MMF-301(A)can be used to replace M301(A)modules in MMF-302(A)OPERATION existing systems. Each MMF-302(A) uses one of the available module MMF401(A)APPLICA TIONS addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status(open/nor- Use to monitor a single device or a zone of four-wire smoke mal/short)of its Initiating Device Circuit(IDC).A flashing LED detectors,manual fire alarm pull stations,waterflow devices,or indicates that the module is in communication with the control other normally-open dry-contact devices.May also be used to panel. The LED latches steady on alarm (subject to current monitor normally-open supervisory devices with special super- limitations on the loop). visory indication at the control panel. Monitored circuit/device is wired as an NFPA Style B(Class B)Initiating Device Circuit. MMF-302(A)SPECIFICATIONS A 47K ohm End-of-Line Resistor(provided)terminates the cir- Nominal operating voltage:15 to 32 VDC. cuit. Maximum current draw:5.1 mA(LED on). MMF-301(A)OPERATION Maximum IDC wiring resistance:25 ohms. Each MMF-301(A) uses one of the available module Average operating current:300 IiA, 1 communication and 1 addresses on an SLC loop. It responds to regular polls from LED flash every 5 seconds,3.9k eol. the control panel and reports its type and the status(open/nor- mal/short)of its Initiating Device Circuit(IDC). EOL resistance:3.9K ohms. MMF-301(A) SPECIFICATIONS External supply voltage (between Terminals T3 and T4): DC voltage: 24 volts power limited. Ripple voltage: 0.1 Vrms Nominal operating voltage:15 to 32 VDC, maximum.Current:90 mA per module maximum. Average operating current:350 pA, 1 communication every Temperature range:320F to 120°F(0°C to 490C). 5 seconds, 47k EOL; 600 pA Max. (Communicating, IDC Humidity range:10%to 93%noncondensing. Shorted). Maximum IDC wiring resistance:40 ohms. Dimensions: 4.5' (11.43 cm) high x 4" (10.16 cm) wide x 125" (3.175 cm)deep. Mounts to a 4" (10.16 cm)square x Maximum IDC Voltage:11 Volts. 2.125"(5.398 cm)deep box. Maximum IDC Current:400 pA. EOL resistance:47K ohms. Temperature range:32•F to 120•F(0•C to 49•C). Humidity range:10%to 93%noncondensing. Page 2 of 4—DF-W121:C•10/06/2010