2018-00234 - alarm system - Laserfiche WebLink

Home Browse Search

FAPT-851 ACCLIMATE PLUS TM LOW-PROFILE INTELLIGENT • 35 watt,50 watt,75 watt,and 100/125 watt digital amplifiers MULTI-SENSOR (DAA2/DAX series and DS series). • Detector automatically adjusts sensitivity levels without • Solid state message generation. operator intervention or programming. Sensitivity increases • Hard-wired voice control module options. with heat. • Firefighter telephone option. • Microprocessor-based technology; combination photo and . 30-to 120-watt analog amplifiers(AA Series). thermal technology. • Backup tone generator and amplifier option. • Low-temperature signal at 40°F±5°F(4.44°C±2.77°C). FSC-851 INTELLIQUAD FlashScan® Exclusive ADVANCED MULTI-CRITERIA DETECTOR World-Leading Detector Protocol • Detects all four major elements of a fire (smoke, heat, CO, At the heart of the NFS2-3030 is a set of detection devices and and flame). device protocol—FlashScan(U.S. Patent 5,539,389).FlashS- • Automatic drift compensation of smoke sensor and CO cell. can is an all-digital protocol that gives superior precision and • High nuisance-alarm immunity. high noise immunity. As well as giving quick identification of an active input device, INTELLIGENT FAASI® DETECTORS FSA-5000, FSA-8000, FSA- this protocol can also activate many output devices in a frac- 20000 AND FSA-20000P tion of the time required by competitive protocols. This high • Connects directly to the SLC loop of compatible ONYX speed also allows the NFS2-3030 to have the largest device series panels. per loop capacity in the industry — 318 points — yet every • Provides five event thresholds that can be individually pro- input and output device is sampled in less than two seconds. grammed with descriptive labels for control-by-event pro- The microprocessor-based FlashScan®detectors have bicolor gramming;uses five detector addresses. LEDs that can be coded to provide diagnostic information, • Uses patented particle separator and field-replaceable filter such as device address during Walk Test. to remove contaminants. • Advanced algorithms reject common nuisance conditions ONYX Intelligent Sensing • FSA-5000 covers 5,000 square feet through one pipe. ONYX Intelligent Sensing is a set of software algorithms that • FSA-8000 covers 8,000 square feet through one pipe. provide the NFS2-3030 with industry-leading smoke detection • FSA-20000 covers 28,800 square feet through one to four capability. These complex algorithms require many calcula pipes. tions on each reading of each detector,and are made possible by the very high-speed microcomputer used by the NFS2- • FSA-20000P covers 28,800 square feet through one to four 3030. addressable pipes. Supports addressable pipes to pinpoint location of alarm events. Drift Compensation and Smoothing. Drift compensation allows the detector to retain its original ability to detect actual FCO-851 INTELLIQUADTM PLUS smoke, and resist false alarms, even as dirt accumulates. It ADVANCED MULTI-CRITERIA FIRE/CO DETECTOR reduces maintenance requirements by allowing the system to • Detects all four major elements of a fire. automatically perform the periodic sensitivity measurements • Separate signal for life safety CO detection. required by NFPA 72. Smoothing filters are also provided by software to remove transient noise signals, usually caused by • Optional addressable sounder base for Temp-3 (fire) or electrical interference. Temp-4(CO)tone. Automatic drift compensation of smoke sensor and CO cell. Maintenance Warnings. When the drift compensation per- • formed for a detector reaches a certain level,the performance • High nuisance-alarm immunity. of the detector may be compromised, and special warnings FMM-4-20 GAS DETECTION MODULE are given. There are three warning levels: (1) Low Chamber value; (2) Maintenance Alert, indicative of dust accumulation • Interface to industry-standard linear scale 4-20 mA sensors. that is near but below the allowed limit; (3) Maintenance • Five programmable thresholds. Urgent,indicative of dust accumulation above the allowed limit. • FM Approved, Class 6320 (Stationary Gas Sensors/ Sensitivity Adjust. Nine sensitivity levels are provided for Detectors). alarm detection. These levels can be set manually, or can SWIFT WIRELESS change automatically between day and night. Nine levels of pre-alarm sensitivity can also be selected, based on predeter- • Self-healing mesh wireless protocol. mined levels of alarm. Pre-alarm operation can be latching or • Each SWIFT Gateway supports up to 50 devices:1 wireless self-restoring,and can be used to activate special control func- gateway and up to 49 SWIFT devices. tions. • Up to 4 wireless gateways can be installed with overlapping Self-Optimizing Pre-Alarm. Each detector may be set for network coverage. "Self-Optimizing"pre-alarm. In this special mode,the detector "learns" its normal environment, measuring the peak analog RELEASING FEATURES readings over a long period of time, and setting the pre-alarm • Ten independent hazards. level just above these normal peaks. • Sophisticated cross-zone(three options). Cooperating Multi-Detector Sensing. A patented feature of • Delay timer and Discharge timers(adjustable). ONYX Intelligent Sensing is the ability of a smoke sensor to • Abort(four options). consider readings from nearby sensors in making alarm or pre-alarm decisions.Without statistical sacrifice in the ability to VOICE AND TELEPHONE FEATURES resist false alarms, it allows a sensor to increase its sensitivity • Up to eight channels of digital audio. to actual smoke by a factor of almost two to one. DN-7070:P•3/8/17—Page 3 of 8