2018-00234 - alarm system - Laserfiche WebLink

Home Browse Search

TFP176 • Page 2 of 6 DEFLECTOR Installation 1 - Frame 2 - Button HAT �` 5 WAWA& The Series TY-FRB, 5.6 K-factor, Hori- 3 - Sealing —.Ale zontal and Vertical Sidewall Sprinklers Assembly I must be installed in accordance with 4 - Bulb Pr; �� ,�� this section. 5 - Compression General Instructions Screw 6 Deflector* / Do not install any bulb type sprin- 6* 4 2 3 1 kler if the bulb is cracked or there is a loss of liquid from the bulb. With the 9/18^ WRENCH 1/2"** sprinkler held horizontally, a small air (14,3 mm) FLATS NPT bubble should be present. The diam- 1 eter of the air bubble is approximately ,�� / 1/16 inch(1,6 mm)for the 135°F(57°C) ` _ / I�� to 3/32 inch (2,4 mm) for the 286°F _O- 116 WI (141°C)temperature ratings. �11 A leak tight 1/2 inch NPT sprinkler joint 1� should be obtained with a torque of 7 1-13/16" 7/16„ to 14 ft.-lbs. (9,5 to 19,0 Nm). Higher (46,0 mm) (11 1 mm) levels of torque may distort the sprin NOMINAL kler and cause leakage or impairment CENTERLINE of the sprinkler. OF SPRINKLER MAKE IN WATERWAY Do not attempt to make-up for insuf- 1-1/2" ficient adjustment in the escutcheon x(38,1 mm)~ plate by under-or over-tightening the *Temperature rating sprinkler. Readjust the position of the is indicated on 2-3/16" _ sprinkler fitting to suit. Deflector. (55,6 mm) ESCUTCHEON Series TY-FRB Horizontal and STYLE ' — PLATE SEATING Vertical Sidewall Sprinkler ** Pipe thread 10 or 20 connections per RECESSED SURFACE Installation ISO 7-1 can be ESCUTCHEON The Series TY-FRB Horizontal and provided on -IAAtli Vertical Sidewall Sprinklers must be special request. installed in accordance with the fol- 1fol- lowing instructions. 2-7/8 0 mm" DIA. rfai-i�IIIIIIIIIIII Step 1. Horizontal sidewall sprinklers are to be installed in the horizontal po- ill V I NI sition with their centerline of waterway perpendicular to the back wall and parallel to the ceiling.The word "TOP" on the Deflector is to face towards the ceiling. ' Vertical sidewall sprinklers are to be FIGURE 1 installed in the pendent or upright po- 5.6 K-FACTOR QUICK RESPONSE sition with the arrow on the Deflector SERIES TY-FRB HORIZONTAL SIDEWALL(TY3331)SPRINKLERS pointing away from the wall. Characteristics Step 2. With pipe thread sealant ap- Physicalaye Bronze Design plied to the pipe threads, hand tighten the sprinkler into the sprinkler fitting. Button Brass/Copper Criteria Sealing Assembly Beryllium Nickel w/ Step 3. Tighten the sprinkler into the TEFLON sprinkler fitting using only the W-Type Bulb Glass The Series TY-FRB, 5.6 K-factor, Hori- 6 Sprinkler Wrench (Ref. Figure 5), Compression Screw Bronze zontal and Vertical Sidewall Sprinklers With reference to Figure 1 or 2,the W- HSW Deflector Bronze are intended for fire protection sys- Type 6 Sprinkler Wrench is to be ap- VSW Deflector Copper tems designed in accordance with the plied to the wrench flats. standard installation rules recognized Operation by the applicable Listing or Approval agency (e.g., UL Listing is based on The glass bulb contains a fluid which the requirements of NFPA 13, and FM expands when exposed to heat.When Approval is based on the requirements the rated temperature is reached, the of FM's Loss Prevention Data Sheets). fluid expands sufficiently to shatter Only the Style 10 or 20 Recessed Es- the glass bulb, allowing the sprinkler cutcheon, as applicable, is to be used to activate and water to flow. for recessed horizontal installations.