Laserfiche WebLink
TFP181 <br /> Page 3 of 4 <br /> FACE OF CLEARANCE HOLE CLEARANCE <br /> SPRINKLER DIAMETER - HOLE <br /> FITTING I DIMENSION C <br /> 1 c J <br /> SPRINKLER 1 =�` <br /> SUPPORT CUP 1 { <br /> ASSEMBLY I i „., II �� <br /> 1/2” (12,7 mm) <br /> THREADED �, ,■IP'S <br /> ADJUSTMENT ( <br /> I <br /> D FACE ( IMI_-. <br /> OF CEILING, <br /> RETAINING RING \ o <br /> •7/ <br /> MOUNTING / i <br /> SURFACE alit\ / I I I / FIGURE 4 <br /> DISPOSABLE PROTECTIVE CAP <br /> N\ t14....—.........21— ma_ — <br /> i i i i Arms during ceiling installation and/or <br /> I I <br /> finish. You can also use the Protective <br /> -i_� T t-r-_7 Cap to locate the center of the clear- <br /> 3/16"to 11/16" MANUFACTURER DEFLECTOR COVER PLATE ance hole by gently pushing the ceiling <br /> (4,8 to 17,5 mm) PRESET GAP IN DROPPED RETAINER material up against the center point of <br /> REFERENCE 3/32" (2,4 mm) POSITION ASSEMBLY the Protective Cap.. , <br /> COVER PLATE COVER PLATE NOTICE <br /> -PROFILE DEPTH - DIAMETER As long as the Protective Cap remains <br /> DIMENSION B DIMENSION A in place, the system is considered <br /> A:3-1/4 inches(82,6 mm) C:2-3/8 to 2-5/8 inches(60,3 to 66,7 mm) "Out of Service". <br /> Step 6.After the ceiling has been com- <br /> B:3/16 inches(4,8 mm) D:1-3/4 to 2-1/4 inches(44,5 to 57,2 mm) pleted with the 2-1/2 inch(63,5 mm)di- <br /> ameter clearance hole and in prepa- <br /> FIGURE 2 ration for installing the Cover Plate/ <br /> SERIES CONCEALED SPRINKLER INSTALLATION DIMENSIONS Retainer Assembly, remove and dis- <br /> card the Protective Cap.Verify that the <br /> Deflector moves up and down freely. <br /> --- If the Sprinkler is damaged and the <br /> Ij=t FRAME ;"j�j` Deflector does not move up and down <br /> / ;/ freely, replace the entire Sprinkler. <br /> ARM \/ 1i Do not attempt to modify or repair a <br /> IIL <br /> damaged sprinkler. <br /> SUPPORT - IC. <br /> �" Step 7. When installing an Air and <br /> CUP Dust Seal, refer to Figure 5; otherwise, <br /> _ ' 1 proceed to Step 8. To attach the Air <br /> „■ r and Dust Seal, verify the angle of the <br /> „■'• �=----- outside edge of the seal is oriented ac- <br /> cortramicy <br /> ding to cording to Figure 5. Start the edge of <br /> -------• O the Retainer in the grooved slot of the <br /> 7/8"(23 mm) Air and Dust Seal and continue around <br /> SQUARE the retainer until the entire Air and Dust <br /> // Seal is engaged. <br /> / Step 8. Screw on the Cover Plate/ <br /> ALIGN //J Retainer Assembly until the Retainer <br /> ARROWS WITH ((// <br /> i \ (shown in Figure 2) or the Air and Dust <br /> FRAME ARMS \_ Seal (shown in Figure 5) contacts the <br /> - r ceiling. Do not continue to screw on <br /> \ I i the Cover Plate/Retainer Assembly <br /> ACCEPTS \ \,_rte so that it lifts a ceiling panel out of its <br /> 0 1/2"SOCKET \ normal position. If you cannot engage <br /> DRIVE the Cover Plate/Retainer Assembly <br /> FIGURE 3 with the Support Cup or you cannot <br /> RFII SPRINKLER WRENCH engage the Cover Plate/Retainer As- <br /> sembly sufficiently to contact the ceil- <br /> ing, you must reposition the Sprinkler <br /> Fitting. <br />