HomeMy WebLinkAbout2001-P04549 - addn/remodel/repair PERMIT
CITY OF O RO N O Permit Number:
2750 Kelley Parkway - PO Box 66 P04549
Crystal Bay, Minnesota 55323 Permit Type: Addition/Remodel/Repair
(952) 249-4600 Date Issued: 11/19/2001
SITE ADDRESS: 685 Old Crystal Bay Rd N
Long Lake,MN 55356
PID: 33-118-23-21-0002
DESCRIPTION: UBC Occupancy B
Proposed Use: Institutional Construction Type VN
Permit Class: Building Census Code 437
Permit Type: Addition/Remodel/Repair Permit Sub-type(s): Addn/Remodel/Repair
DETAILS:
Approved per resolution#:
Separate permits required: Piumbing iviechanicai Eieciricai(state)
NOTICES/REMARKS:
FEE SUMMARY: Permit Fee: $ 3,542.50 Valuation: $ 565,000.00
Plan Review Fee: $ 2,318.12
State Surcharge Fee: $ 285.00
TOTAL FEE: $ 6,145.62
APPLICANT: Oakwood Builders,Inc. OWNER: Orono Public Schools
12901 Pioneer Trail 765 Old Crystal Bay Rd N
Eden Prairie,MN 55437 Long Lake MN 55356
THE UNDERSIGNED HEREBY REQUESTS PERMISSION TO MAKE THE REAL IMPROVEMENTS SPECIFIED
AND AGREES TO DO ALL WORK IN STRICT COMPLIANCE WITH ALL CITY OF ORONO ORDINANCES AND STATE OF
MINNESOTA BUILDING CODE REQUIREMENTS.
APPLICANT PERMITEE SIGNATURE I01EDBYSIGNATURE
Conies: 1-File(Siznitures Required). 1-ADDlicant. 1-Monthlv Reports. 1-Assessine. I-Finance Page 1
Oct-23-2001 08:14am From—CITY OF ORONO +9522494616 T-049 P.006/007 F-642
� 1
Total Fee: $ "I p Date Received: 146
• Entered By: ( Permit#.
14 koG 7161
CITY OF ORONO - B PERNUT APPLICATION
All information must be submitted in full before plan review will be started.
(please prim-all information)
THE APPLICANT IS: (circle one) GWNER OR �ONLTCT_0I �
JOB SITE ADDRESS: � ZIP:
NAME OF OWNER: t PHONED)
—] (work)
MAILLVG ADDRESS:' L 'CITY: O QLD ZIP
CONTRACTOR: . PHONE: CI z'
CONTACT PERSON: OBILE/PAGER:
MAILING ADDRESS: I ja _ CITY: Lilln Val: `t?ZIP::L�
STATE LICENSE: #
ARCHITECT/ENGINEER: PHONE- IL
6
MAILING ADDRESS:' CITY: ZIP:
NANIE: S usa N 141 sv� 4�6_1b" REGISTRATION#
TYPE OF WORK: New Addition Accessory Structure
Move Remodel/Alteration Land Alteration
OPOSED WORK(describe in d tail): I i ll t
P
STORIES: SQ.FEET OF EACH FLOOR: ^' 7 .Svo
NO. OF BEDROOMS: GARAGE STALLS: ATT. DET.
ESTIMATED CONSTRUCTION VALUATION(excluding land): $ #sbs- 0aa
I hereby apply for a building permit and I acknowledge that the information above is complete and
accurate; that the work will be in conformance with the ordinances and codes of the City and with
the State Building Code; that I understand this is not a permit and work is not to start without a
permit; and that the work will be in acc rdance WiAh the approved plan.
APPLICANT'S SIGNATURE: DATE: 16 - Z'4-GI,
NOTE! Parade of Homes events require separate permit approval by Police Department and
City Council 60 days prior to the event. Non permitted events will not be allowed.
5
CHECK OFF LIST FOR ISSUANCE OF PERMITS
FOR OFFICE USE ONLY
ADDRESS OR LEGAL: 6rd ls- OC,N C w%(ST A%/ R D Ao
PID:
DESCRIPTION OF WORK: O r-f►cis iZ.�-�vw
ZONING REVIEW BY: DATE APPROVED:
BUILDING REVIEW BY: DATE APPROVED;
FEES TO BE CHARGED: Misc. Fees Calculated By:
PERMIT Yes No
PLAN REVIEW Yes 4/' No SEWER CONNECTION
STATE SURCHARGE Yes—� No WATER CONNECTION
INVESTIGATION FEE Yes No PARK FEE
SAC Yes No SITEINSPECTION
Number of SAC-Units OTHER (specify)
ZONING CHECK LIST Zoning District: No C lft&,eVGe
Fire Department: Post Office: School District:
Lot Area: Sq.ft. Acres Width Depth
Survey Submitted: Yes No Date of Survey:
Proposed Setbacks:
Front(Lake): Ri t Side:
Rear(Street): Le Side:
Adjacent Structures: Wetland:
Building Height: Def. Hgt. Peak Hgt.
Lot Coverage:
Grading: Staff Approval Date: By: Council Approval Date:
Septic: Staff Approval Date: By:
Zoning File: # Resolution: # Resolution Date:
Shoreland District:
Avg. Setback: Bluff Se ack: Lot Coverage:
Existing Proposed
Hardcover: 0-75'
75-250'
250-500'
500-1000'
Hardcover Variance Required: Yes N Date of Council Approval:
REMARKS Cm house):
7
WELDING REVIEW CHECK LIST
UBC: & CONSTRUCTION TYP • 44ty
Sq Footage $Per Sq Ftg
Basement, x —
1st Floor x =
2nd Floor x =
Garage x _
x =
TOTAL
Estimated Construction Value: $ 56S Coo
Inspections Required: Work Requiring Separate F ermits:
Site Plumbing Fire
Hardcover Removal Mechanical Water Connection
• Footing Septic Sewer Connection
_X Framing Fireplace Lawn Irrigation
_ Insulation (Masonry) Other
Wall Board (Mfg.) Well(State Permit)
Final Grading/Filling Electrical(State Permit)
Other
REN ARKS(IN HOUSE):
REVIEW BY OTHERS: DA ----- --
Access: Existing New 7
Access Approval: Date By:
REMARKS (TO BE NOTED ON PERMIT):
8
I
Oct723-2001 08:15am From-CITY OF ORONO +9522494616 T-049 P.00T/OOT F-642
Sec.13.04 RIGHTS OF SUBJECTS OF DATA
Subd. 1. Type of data. The rights of individual on wham the darn is stored or w be stored shall be as set forth in this section.
Subd.2_ Information required to be given individual. -%a individual asked to supply private or confidential data concerning himself
shall be informed of (a)the purpose sad intended use of die requenid dare within the sollec&g state agency,political subdivision,or satewide
system:(b)whetter he may refuse or is legally required to supply d-e requested darn:(e)any known consequence arisinS from his supplying or
refusing ro supply private or confidential dam:and(d)die identity of ether persons or entities authorised by state or federal law to receive the dam.
This requirement shall not apply when an individual is asked to supply investigative data,pursuant to section 13.82,subdivision S.to a law
enforcement officer.
The commissionersrf_revenue may olaeo tha-mdet reniti*rrd under[hit subdivisinntilthe indMdual lnenme nY or vroa;•ty tax regindd
inctrucrions instead of on those forms.
Subd.3. Access to data by individual. Upon request.a a responsible authority,an individual shall be informed whether he is the
subject of stored data on individuals,and whether it is classified as public,private or confidential. Upon his titt'dher toques;,an individual who
is the subject of stored private or public dam on individuals shall be shown the data without any charge to him aal,if he desires,shall be informed
of the content and meaning of that dam. After an individual has boon shown the private dam ted informed of its meaning,rhe dares treed not be
disclosed to him for six months thereafter unless a dispute or action pursuant to this section is pending or additional dam on tha individual has been
collected or created. The responsible authority shall provide copies of the private or public dam upon request by tbo individual subject of the dare.
The responsible authority may require the requesting person to pay the actual costs of making.cartiWag,and compiling the copies.
The responsible authority shall comply immediately,if possible.with any request made putsuanr to this subdivision,or within five days
of the dace of the request,excluding Saturdays,Sundays and legal holidays,,if immediate compliance is not possible. If he cannot comply with
the request within that time,be shall so inform the individual,and may have an additional five days within which to comply with the request.
excluding Saturdays,Sundays and legal holidays.
Subd.4. Procedure when data Is not accurate or complete. An individual may contest the accuracy or completeness of public or
private dam concerning himself. To exercise This right,an individual shall notify in writing the responsible authority describing the nature of the
disagreement The responsible authority shall within 30 days either: (a)correct roe data found to be iciac==or incomplete and anompt to notify
past recipients of inaccurate or incomplete data,intruding recipients named by the individual.or(b)notify die individual that he believes the dam
to be correct. Dara in dispute shall be disclosed only if the indivich al's statement of disagreement is included with the disclosed dam.
The determination of die responsible authority may be appealed pursuant to tic pmvisiotns of the administrative procedure act relating
to contested cases.
DATA PRIVACY ADYISARY
In accordance with M.S. 13.04, Subd. 2, "Rights of subjects of data", we would like to inform you that your
request for a permit or license from the City of Oronc or any of its departments may require you to furnish certain
private or confidential information.
You are notified that:
l. The information you furnish will be used to determine your qualification for the permit or license
requested.
2. You may refuse to supply data, but refusal may require that the City deny the permit or license.
3. The information may be shared with other local, state or federal agencies to the extent necessary to
process the permit or license.
4. If your requested permit or license requices Council action to approve, some information may become
public.
5. You have certain rights under M.S. 13.04(available upon request) to review private data on yourself.
6. Your full name is required to process this application or permit.
XrsL Last
.Address
\ J�
Pd 0/1 PM
1
City State zip Phone
I underst m ri is stated above.
Sigtnature �
6
ORONO L-00 ' k
E.2
0
ORONO DISTRICT OFFICE
As of September 27,2001 Commission No. 01 088
GENERALS _
Name I Address City State Zip Tel I Fax
LS Black 1959 Sloan Place St. Paul MN 55117;651-774-8445 651-774-9695
Constructors, Inc.
Environ Con, Inc. 500 Apollo Avenue St.Cloud MN 56304 320-253-1106 320-253-9047
NE
McFarland Const 50 Ninth Avenue S. Hopkins MN 55343 952-936-7662 952-936-7664
PMI Const 2310 W. County New Brighton MN 55112 651-636-1499 651-636-1699
Road D, Ste 105
BNM Construction, 9766 Pierce St NE Blaine MN 55434 612-780-4535 612-792-0864
Inc.
Gen-Con 614 North Broadway Jordan MN 55352 952-492-1111 952-492-7780
The Builders, Inc. 8100 Wayzata Bbd. Minneapolis MN 55426 763-545-3217 763-545-3209
Oakwood Bldrs 12901 Pioneer Trail Eden Prairie MN 55347 952-941-9730 952-941-7715
Merrimac Const 14533 Highway 65 Anoka MN 55304 763-4346857 763-434-6568
NE
Dew Corporation 2125 Century N.St. Paul MN 55109 651-777--4900 651-777-4994
Avenue
Maertens Brenny 8251 Main Street NE Minneapolis MN 55432 612-786-4779 612-786-6973
JS Cates Const 2400 Cates Ranch Hamel MN 55340 763-478-8961 763-478-8794
Drive
ELECTRIC
Name Address City State Zip Tel Fax
Metro Electric 2825 North Second Minneapolis MN 55411 612-588-6658 612-588-6748
Street
Baker Electric 234 Water Street Excelsor MN 55331 952-474-3072 952-474-0875
Kilmer Electric 51241 Lakeland Crystal MN 55429 763-425--2525 763-424-1258
Avenue N
Phasor Electric 15300-25th Avenue Plymouth MN 55447 763-557-9702 763-557-1295
N, Ste 400
Dymanyk Electric, 1915 NE Broadway Minneapolis MN 55413 612-379-4112 1612-379-0459
Inc. Street
AJ Moore Electric 413 North Third Delano IMN 1 55328 763-972-5961 763-972-5867
Street
MECHANICALS
Name Address City State Zip Tel Fax
Kumar Mechanical, 877 SW 3rd St,Ste 1 New Brighton MN` 55112 651-636-6564 651-636-2093
Inc.
Master Mechanical, 1027 Gemini Road Eagan MN 55121 651-905-1600 651-905-1601
Inc.
Rouse Mechanical, 7320 Oxford St St. Louis Park MN 55440 952-933-5300 952-933-1688
Inc.
Conrad Mechanical 509-1st Avenue NE Minneapolis MN 55413 612-379-8200 612-379-0268
Northwest 110 Sycamore St St. Paul MN 55117 651-310-0102 651-310-0403
Sheetmetal of St.
Paul
` 0 WOLD ARCHITECTS
r AND ENGINEERS
305 ST. PETER STREET
ST. PAIL., MN 55102
651.227.7773
TO: Prospective Bidders FAX 6 51.2 2 3.5 6 4 6
25 SOUTH GROVE AVENUE
FROM: Wold Architects and Engineers SUITE 500
ELGIN, IL 60120
847.608.2600
DATE: September 26,2001 FAX 847.608.2654
WWW.WOI.DAE.COM
COMM.No: 01088 MAIL a WOLDAE.COM
SUBJECT: Addendum No. 1 for Bidding Documents for the: DISTRICT OFFICE
EXPANSION
Orono,Minnesota
BIDS DUE OCTOBER 4,2001 AT 2:00 P.M.
This addendum forms a part of the Contract Documents dated September 11, 2001.
Acknowledge receipt of this Addendum on the space provided on the Bid Form.
Failure to do so may result in disqualification of Bid.
This Addendum consists of three(3)typed sheets and attachments:
Specification Sections: 08700-9, 16478; Details of Construction: 8/4-3, 2/5-1. 8/6-1;
Drawings R1/A1.1,R2/A1.1, R1/M2.3.
NOTICE: A PRE-BID WALKTHROUGH WILL BE AVAILIABLE ON SITE
TUESDAY,OCTOBER 2,AT 1:00 PM.
PROJECT MANUAL
1. SECTION 08700 HARDWARE. Paragraph 3.04 HARDWARE SCHEDULE
issued this addendum.
2. SECTION 16478 TRANSIENT VOLTAGE SURGE SUPPRESSION.
Reissued this addendum.
PRIOR APPROVALS
The following sche iule amends designated specification sections to list additional
acceptable manufact,Irers. Use of any product by any of these manufacturers will be
permitted only if of,,r review of shop drawings or detailed product data per Section
01300, Architect determines that proposed materials or equipment are equivalent in
performance, construction and appearance to product(s) specified.
Where anticipated product substitutions would alter the design or space requirements
indicated on the Drawings, pay for cost of design and construction revisions including
the cost of associated work by other contractors.
Pagel of 3
o
(PRIOR APPROVALS—Continued)
For complete requirements, see Specification Section 01630 = Substitutions and
Product Options.
Section No. Item Type Acceptable Manufacturer
08200 2.0I.A.I Wood Doors Oshkosh
15440 P-2H ADA Lavatory Plumberex Specialty Products
15862 2.02 Variable Frequency Yaskawa
Drive
15910 2.01 Dampers Pottorff
15910 2.02 Fire and Smoke Dampers Pottorff
DETAILS OF CONSTRUCTION
1. DETAIL 8/4-3 FLOORS/WALLS. Revised this addendum.
2. DETAIL 2/5-1 DOOR/OPENING SCHEDULE. Reissued this addendum.
3. DETAIL 8/6-1 STAIR/RAILING. Issued this Addendum.
DRAWINGS
1. DRAWING A0.1 DEMOLITION PLANS
A. Add Keynote 55: Demolish Ceiling
B. Drawing H6/A0.1 Main Level Demolition Plan: Add Keynote 55 to rooms
A127,A131,A132,and A133.(See A1.1 for locations of rooms).
2. DRAWING A1.1 FLOOR PLANS
A. Revise Drawing H1/A1.1 Main Level Floor Plan per attached R1/A1.1.
B. Revise Drawing H6/A1.1 Upper Level Floor Plan per attached R2/A1.1.
3. DRAWING S1 TITLE SHEET
A. Add the following section:
"Composite Steel Deck
Weld composite steel deck to supports with 5/8"diameter puddle welds at
12"o.c. Screw side laps at 36"max o.c.with#10 Tek screws. Deck flutes
and ribs must line up from one span of deck to the next."
4. DRAWING M1.1 MECHANICAL PLAN LOWER LEVEL
A. Add the following to key note#4:
"Support all piping on field fabricated supports securely anchored to floor.
Do not support piping from structure above. The inlet is to allow the steam
piping to be completed and operational prior to new floor construction.
Provide plywood protection of all piping during the course of construction."
Page 2 of 3
DO 5. DRAWING M2.3 MECHANICAL SCHEDULES
A. Delete VAV Terminal Unit Schedule with RI/M2.3
6. DRAWING E2.1 FLOOR PLAN POWER AND SYSTEMS—SCHEDULES
A. Motor and Equipment Schedule: Revise motor#6, RE-1 to be controlled by
VFD supplied by Division 15. Division 16 to install VFD in mezzanine and
connect complete.
END OF ADDENDUM#1
Page 3 of 3
3.04 HARDWARE SCHEDULE
Hardware Group 1
Butts
Classroom Lock L9070
Stop
Hardware Group 2
Butts
Classroom Lock L9070
Closers—Stop 4111 CUSH
Kick Plate
Gasketing
Hardware Group 3
Butts
Storeroom Lock L9080
Stop
Hardware Group 4
Butts
Storeroom Lock L9080
Closer
Gasketing
Stop
Hardware Group 5
Butts
Privacy Lock L9040
Stop
Hardware Group 6
Butts
Exit Device 99L-F
Removable Core Cylinder
Closer
Kick Plate
Gasketing
Stop
END OF SECTION 08700
08700-1 No. 01088
SECTION 16478
TRANSIENT VOLTAGE SURGE SUPPRESSION
PART 1: GENERAL
1.01 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
Specification Sections, apply to this Section.
B. Requirements of the following Division 16 Sections apply to this Section:
1. Section 16010: 'Basic Electrical Requirements".
2. Section 16050: 'Basic Electrical Materials and Methods".
3. Section 16110: "Raceways".
4. Section 16120: "Conductors and Cables".
5. Section 16452: "Grounding".
6. Section 16470: "Panelboards".
C. Related Sections:
1. Section 16195: "Electrical Identification"for labeling materials.
2. Section 16475: "Overcurrent Protective Devices" for circuit breakers, fusible switches, fuses, and other
devices used in panelboards.
1.02 SUMMARY
A. This Section includes Transient Voltage Surge Suppression (TVSS) equipment of parallel design for power
distribution systems rated 600 V and less. Extent of TVSS work is indicated by drawings and schedules, and as
specified herein. It includes requirements for equipment for this project including,but not limited to,the following:
1. Branch Circuit Panelboards.
1.03 DEFINITIONS
A. "Transient Voltage Surge Suppression": Devices used for the protection of all AC electrical circuits from the
effects of lightning induced currents, substation switching transients and internally generated transients resulting
from inductive and/or capacitive load switching and high frequency electrical line noise filtering. It protects for
surge currents in both directions.
1.04 SUBMITTALS
A. General: Submit the following in accordance with the Conditions of the Contract and Division 1 Specification
Sections:
1. Product Data: Submit product data for each type of TVSS assembly, accessory item, and component
specified.
16478-1 No. 01088
2. Shop Drawings: Submit shop drawings from manufacturers of TVSS equipment including dimensioned plans,
sections,and elevations. Show tabulations of installed devices,major features,and voltage rating. Include the
following:
a. Enclosure type with details.
b. Bus configuration and current ratings.
C. Short-circuit current rating of assembly.
d. Features, characteristics, ratings, and factory settings of individual protective devices and auxiliary
components.
e. Wiring Diagrams: Details of schematic diagram including control wiring and differentiating between
manufacturer-and field-installed wiring.
f. Dimensional drawing of each surge suppression device type indicating mounting arrangements.
g. UL 1449-1998 clamp voltage documentation.
3. Maintenance Data: Submit maintenance data for switchboard and panelboard components, for inclusion in
Operating, Maintenance and Warranty Data Manual specified in Division 1 and in Section 16010, "Basic
Electrical Requirements." Include manufacturer's written instructions for testing.
4. Qualification Data: Submit for firms and persons specified in"Quality Assurance"Article.
5. Field Test Reports: Indicate and interpret test results for compliance performance requirements.
1.05 QUALITY ASSURANCE
A. Codes and Standards:
1. Electrical Component Standard: Comply with NFPA 70, "National Electrical Code" for components and
installation.
2. UL Standards: Comply with UL 1449(2nd Edition),UL 1283 and(UL 67 only for internal panelboard units).
3. Listing and Labeling: Provide products specified in this Section that are "Listed"and"Labeled".
a. The Terms"Listed" and"Labeled": As defined in the National Electrical Code,Article 100.
4. FCC Emission Standard,Part 15, Subpart J for Class A applications.
5. Federal Information Processing Standards Publication 94,FIPS pub 94.
6. American National Standards Institute and Institute of Electrical and Electronic Engineers (ANSI/IEEE
C62.41-1991 Categories A,B and C,and C62.45-1992).
7. Canadian Standards Association(CSA).
B. Exceptions: List any exceptions,included with the Bid,to any part of these specifications.
1.06 DELIVERY,STORAGE AND HANDLING
A. Deliver transient voltage surge suppression equipment in factory fabricated containers or wrappings,which properly
protect equipment from damage or construction dust.
B. Store in original packaging. Store inside well-ventilated area protected from weather, moisture, soiling, extreme
temperatures,humidity,and laid off ground.
C. Handle carefully to prevent damage. Follow manufacturer's written instructions for handling, storing and
installation. Do not install damaged equipment;replace with new.
16478-2 No. 01088
PART 2: PRODUCTS
2.01 MANUFACTURERS
A: Manufacturers: Subject to compliance with requirements,provide products by one of the following:
1. Current Technology,Inc.
2. LEA International,Inc.
3. Liebert Corp.
4. Cutler-Hammer.
5. United Power.
6. APT,Inc.
2.02 REQUIREMENTS,GENERAL
A. Environmental:
1. Operating Temperature: -40°C to+60°C.
2. Relative Humidity: 5 to 95%.
3. Operating altitude: 0 to 12,000 feet.
4. Audible Noise: Less than 35 DBA at 3 feet.
B. Cabinet:
1. Provide a NEMA 1 cabinet with front accessible lockable hinged door(or screw-attached door)and for surface
wall or equipment or building structure mounting as indicated. Provide over-current protection within TVSS
cabinet.
C. Monitoring:
1. Provide cabinet with LED visual status monitoring for indication of system operation noting that system is
operating properly and visual LED status monitoring indication noting that the system has a fault. Provide
cabinet with audible status monitoring that will alarm on a system failure in the event the protection has failed.
Provide audible alarm silence push-button.
D. Description: IEEE C62.41, selected to meet requirements for category indicated.
1. Exposure: Low.
2. Exposure: Medium.
E. Impulse sparkover voltage coordinated with system circuit voltage.
F. Factory mounted assembly with UL-recognized mounting devices.
2.03 EXTERNALLY MOUNTED PANELBOARD TVSS
A. General: Design for non-linear loads that provide transient voltage surge suppression (TVSS) and high-frequency
electrical line-noise filtering for Medium to Low Exposure levels at secondary distribution and branch circuit
panelboards that are externally mounted adjacent panelboard.
1. Include coordination of TVSS equipment manufacturer installation with panelboard manufacturer.
2. Refer to drawings and/or panelboard schedules and to Section 16470 "Panelboards" for panelboards
designated to be protected with TVSS.
3. Mount adjacent to panelboard as close as feasible, keeping feeder length as short as feasible; twist feeder
conductors to reduce impedance.
B. Operating Voltage: Refer to drawings and panelboard schedules for voltage and configuration.
16478-3 No. 01088
C. Maximum Continuous Operating Voltage (MCOV) of Suppression Components: Provide suppression components
utilized for panelboards that are rated not less than 115%of nominal system operating voltage of the panelboard.
D. Tested Single-Pulse Surge Current Capacity: Submit to the Engineer along with the shop drawings for compliance.
Provide test data indicated that the tested single-pulse surge current capacity, in amperes, based on the current
waveform of ANSI/IEEE C62.41-1991 for category B3 Medium Exposure Waveform(6KV, 3KA, 8x20 micro-sec
waveform), is not less than the following:
Mode of Protection: Tested Single-Pulse Surge Current(AMPS):
Distribution Panelboards Branch Circuit Panelboards
L-N(Each Phase) 80,000 50,000
L-G(Each Phase) 80,000 50,000
N-G 80,000 50,000
E. UL 1449 (ANSI C62.41-1991 Cat. B3) Performance Ratings: Provide published performance rating literature,
based on UL 1449 listed clamping voltage suppression ratings, for the entire system as follows:
Nominal System Voltage: Mode of Protection(Volts):
Distribution Panelboards Branch Circuit Panelboards
120/208 L-N: 500 LN: 400 to 600
L-G: 500 L-G: 400 to 600
N-G: 500* N-G: 400 to 600
F. Provide suppression elements between all phases of phase-to-phase (on delta systems) and for 3 phase, 4-wire plus
ground (on grounded wye) configurations between each phase conductor and the system neutral, between each
phase conductor and the system ground and between the neutral and the system ground. UL clamping levels shall
be the same for all modes noted herein.
G. Provide visible indication of proper suppressor,connection and operation.
H. Provide the suppressor to exhibit Sine Wave Tracking circuitry that has field replaceable circuitry without
disturbing the conduit,enclosure,or cover.
I. Provide a TVSS clamping response time of 1 nanosecond or less. Provide high frequency noise filtering for UL
1283.
J. Provide suppressors consisting of solid-state components that operate bi-directionally.
K. Provide the surge suppression panel with a surface or recessed cover, and mounting as indicated.
L. Provide the surge suppressor with its own disconnect switch or C.B. (unless indicated in the schedules for dedicated
3P circuit breakers) that meets the proper A.I.C. of the panelboard; tap bus of panelboard. If fuses are used for
over-current protection, use fuses that allow the maximum rated transient surge current to pass through the
suppressor a minimum of 1,000 times without fuse operation. Indicate if the system required an external O.C.
device to maintain the systems UL 1449 Listing.
M. Provide the suppressor with a warranty guarantee for a period of 10 years from the date of final acceptance based on
the Architect's final certificate of completion, for all materials (except if determined to be caused by abuse), at no
charge to the Owner.
164784 No. 01088
N. Manufacturers: Subject to compliance with requirements,provide products by one of the following:
a. Current Technology,Inc. TGGO Series
b. LEA International,CF Series.
C. Liebert/Control Concepts,Accuvar III Series
d. Cutler-Hammer,Clipper Series.
e. United Power,Approved Equal.
PART 3: EXECUTION
3.01 INSTALLATION
A. General: Install surge suppression/filter assemblies and accessory items in accordance with these specifications,
applicable codes and standards and in accordance with manufacturers'written installation instructions.
B. Mounting: Mount externally mounted units as close as feasible to switchboard(s) and/or panelboard(s), except as
indicated. (Field verify the best location to provide the shortest conductor lead length):
1. Mount plumb and rigid without distortion of box. Mount flush panels uniformly flush with wall finish.
2. Install on load side of service entrance switchboard or panelboard. Tap the bus and provide disconnect switch
or 3 pole circuit breaker of size as required by the TVSS manufacturer as required to meet NEC if not internal
to unit. Meet requirements of fusing as noted above.
3. Conductor Lengths: Provide externally mounted assembly using switchboard type low impedance conductors
between suppressor and point of attachment and straight and short as possible. Do not exceed 10'-0" of lead
length of conductors without written permission of Engineer for switchboard installation or 24"for panelboard
installations.
3.02 IDENTIFICATION
A. Identify field-installed wiring and components in accordance with Section 16195, "Electrical Identification".
3.03 GROUNDING
A. Panelboard Connections: Make suppressors grounding connections to the panelboard ground bus.
3.04 CONNECTIONS
A. Tighten electrical connectors and terminals, including grounding connections, in accordance with manufacturer's
published torque- tightening values. Where manufacturer's torque values are not indicated, use those specified in
UL 486A and UL 486B.
3.05 FIELD QUALITY CONTROL
A. Quality Control Program: Conform to the following:
1. Procedures: Manufacturer's representative shall visit the site, verify installation, and submit to Engineer or
Architect, a letter stating that the equipment and installation meets the intent of the Contract Documents and
the warranties and guaranties are in effect.
2. Protective Device Ratings and Settings: Verify indicated ratings and settings to be appropriate for final system
configuration and parameters. Where discrepancies are found, recommend final protective device ratings and
settings.
16478-5 No. 01088
B. Visual and Mechanical Inspection: Include the following inspections and related work:
1. Inspect for defects and physical damage.
2. Exercise and perform operational tests of all mechanical components and other operable devices in accordance
with manufacturer's instruction manual.
3. Check mounting,area clearances,and alignment and fit of components.
4. Check tightness of bolted electrical connections, including grounding connections. Refer to manufacturers
written instructions for proper torque values.
5. Perform visual and mechanical inspection and related work.
C. Electrical tests: Prepare for acceptance tests and include the following items performed in accordance with
manufacturer's written instructions:
1. Insulation resistance test of each component,connecting supply,and portions of control wiring that disconnect
from solid-state devices through normal disconnecting features.
2. Ground resistance test on equipment ground connections.
3. Continuity tests of each circuit.
D. Re-test: Correct deficiencies identified by tests and observations and provide re-testing. Verify by the system tests
that the total assembly meets specified requirements.
3.06 CLEANING
A. Upon completion of installation, inspect interior and exterior of switchboards and panelboards. Remove paint
splatters and other spots,dirt, and debris. Touch up scratches and mars of finish to match original finish.
END OF SECTION 16478
16478-6 No. 01088
DETAIL OF • •
WOM ARCHITECT'S AND ENGINEERS
E.2
305 ST.PEM STREET'ST.PAUL,NN 55102
FAX: 651.223.5646 TEL: 651.227.7773
L025 SOUTH GROVE AVEVUE,SUM 500
ELGIN,IL 60120
FAX: 847.608.2654 TEL: 847.608.2600
EXISTING WALL
"
2
1 FURRING/ CHANNELS
5/8"/ GYP
BD
ix
WA DETAIL
AI
A
L DE L
1
3-3
SILL BELOW
ALUMINUM WINDOW
SEALANT
5TL TUBE- SEE STRUGT
5TL STUD FRAMING-
WELD TO TUBE
EXISTING WALL
5/8" GYP BD ON
6" MTL STUDS
® ib" O.G.
COLUMN DETAIL
SUBJECT: FLOORS / HALLS
DATE: 9/11/01 COMMISSION NO: 01088 8
REVISIONS A ADDENDUM #1 REV. DATE 9/26/01
5:�YSD278 W 5_ORONO�Ol08b�DETP.IL4f 300B.DYK
SEAT 0 9/27/2001 0 10+49:58-VDI
DETAIL
• WOLD ARCHITECTS AND ENGINEERS
305 ST.PETER STREET
O ST.PAUL,MN 55102
FAX: 651.223.5646 TEL: 651.227.7773
25 SOUTH GROVE AVENUE,SUITE 500
ELGIN,H.60120
FAX: 847.608.2654 TEL: 847.608.2600
DOOR DOOR LAB FRAME GL MOUNTING CONDITIONHDW REMARKS
NUM TYPE WIDTH HEIGHT MATL EL ELEV EPT MATL HEAD JAMB SILL GRP (SP)
A102 N 3-0 7-0 WD 20/4514 H.M. 4/5-4 5/5-4 IB/54 2
A103 F 3-0 7-0 WD 2 H.M. IA/5-4 IA/5-4 IB/5-4 1
A104L - 8-0 3-8 - - 3 H.M. lA/54 IA/54 IA/54
A105 F 3-0 7-0 WD 2 H.M. lA/54 lA/54 IB/54 1
A106 F 3-0 7-0 WD 4 H.M. 1A/54 IA/54 1B/54 1
A107 F 3-0 7-0 WD 2 H.M. IA/5-4 IA/54 1B/54 1
A108 F 3-0 7-0 WD 2 H.M. IA/5-4 IA/5-4 IB/5-4 1
A109 F 3-0 7-0 WD 2 H.M. IA/5-4 IA/5-4 iB/54 1
A110 F 3-0 7-0 WD 1 H.M. IA/5-4 IA/5-4 - 3
Alll F 3-0 7-0 WD 2 H.M. IA/5-4 M/54 1B/54 1
Al 12 F 3-0 7-0 WD I H.M. IA/5-4 IA/5-4 - 3
Al 13 F 3-0 7-0 WD 2 H.M. IA/5-4 IA/5-4 IB/54 1
Al 14 N 3-0 7-0 WD 1 H.M. IA/5-4 IA/5-4 - 1
Al 16 F 3-0 7-0 WD 2 H.M. IA/5-4 IA/5-4 1B/54 1
Al 17 F 3-0 7-0 WD 2 H.M. 1A/5-4 IA/5-4 1B/54 1
Al 18 N 3-0 7-0 WD 20 1 H.M. 1A/54 IA/54 2
Al 19 F 3-0 7-0 WD - 1 H.M. IA/5-4 IA/54 3
A120 F 3-0 7-0 WD 20 1 H.M. IA/5-4 IA/5-4 5
A121 F 3-0 7-0 WD 20 1 H.M. IA/54 IA/5-4 5
A122A F 3-0 7-0 WD - 5 H.M. IA/5-4 IA/5-4 1B/54 6
A122B F 3-0 7-0 WD 5 H.M. IA/5-4 IA/5-4 1B/5-4 6
A124A F 3-0 7-0 WD - 5 H.M. IA/5-4 1A/5-4 IB/5-4 6
A124B F 3-0 7-0 WD 5 H.M. IA/5-4 IA/5-4 1B/5-4 6
A125 F 3-0 7-0 WD 1 H.M. IA/5-4 2/5-4 1
A126 F 3-0 7-0 WD 1 H.M. IA/5-4 lA/54 1
A130 F 3-0 7-0 WD 1 H.M. 3A/5-4 3B/54 1
A131 F 3-0 7-0 WD 20 1 H.M. 3A/54 3B/5-4 - 1
A132 F 3-0 7-0 JWD 1 H.M. IA/5-4 1A/54 - 3
A133 F 3-0 7-0 JWD - 1 H.M. IA/54 IA/5-4 - 3
A202 F 3-0 7-0 1 WD 1 I 1H.M. I 13A/5-4 3B/5-4 - 14
A203 IF 3-0 7-0 1 WD 1 1 1H.M. I 13A/5-4 3B/5-4 14
Printed 9/27/01
SUBJECT DOOR/OPENING SCHEDULE
DATE: 9/11/01 COMMISSION NO: 01088 2
REVISIONS: REV DATE: 5-1
DETAIL OF • •
WOLD ARCMEM AND ENGINEERS
305 SL.PE'T'ER MEET
ST.PAUL,MN 55102
EW 02�:L 0 FAX: 651.223.5646 TEL: 651.227.7773
25 SOL"LFI GROVE AVIENU,SUITE 500
ELGIN,IL 60120
PAX: 817.608.2654 TEL: 847.608.2600
ALL METAL TO BE PRIMED, EXPOSED
METAL TO BE PAINTED.
ALL EXPOSED WELDS TO BE GROUND
SMOOTH.
SERIES GHB " x 1 4" HEAVY 2 / E WELD
5TL GRATING
WELD GRATE TO ANGLE
G E
N
GONTI
UOUS 4X 4"X 3/8 ANGLE WITH
1/2 EXP. T T
BOL 5 A 2'-0" O.G.
3" x 3" x 1/4" x 8" LONG ANGLES
® 3'-0" O.G. MAX
3/16
REMOVE WALL AS NEEDED TO
WELD ANGLE TO EXIST BEAM -
GROUT WALL 50LID AROUND ANGLE
EXISTING WALL AND BEAM
FLOOR GRATING
1 1/2" = 1'-O"
SUBJECT: STAIR / RAILING
DATE: 9/11/01 COMMISSION NO: 01088 8
REVISIONS A REV. DATE
51U5D278 W5_0R0N0\01088\DETAILY51008DW
SEAT 0 9/27/2001-11:40,55 0 VDI
DETAIL OF CONSTRUCTION
WOLD ARMITECrS AND ENGINEERS
O305 ST.PETER STREETST.PAUL,MN 55102
FA)r-. 651.223.5646 m. 651.227.7773
25 SOUTH GROVE AVENUE,SUM 500
ELGIN,rL 60120
FAX 847.608.2654 TEL: 847.608.2600
0
1-2
UTOILET VTOILET
ii
A120 FA121]
9-0
.........................................
.................
..........................................
..............
.........................
GORRIDOR
A122A
A122
A
XI
10
4-3
22A
..........
A
x
O............
REMOVE FLOOR
RECEPTION 5
.......... AS NEEDED FOR TRENCH
A101
(SEE MEGH) PATCH
INC . ... ... .... ... ...
.... ......
WITH GONGRETE AND
)
2 MATCH ADJACENT FINISH
... ... ... .....
AiO4L
Lr)
WORK ROOM
4-3 A104
9-0
SUBJECT: REV15ION5 TO H1/A1.1
DATE: 9111/01 COMMISSION NO: 01088
REVISIONS Al REV. DATE 9/26/01
5.VSD27BW5_OROND�OKJBB�ARGHWI-II7WC
5EAT 0 9/27/2001 0 12!56,59 0 VDI
Department of Administration
LETTER OF AGREEMENT
DELEGATION OF STATE BUILDING CODE ADMINISTRATION
FOR PUBLIC BUILDINGS AND STATE LICENSED FACILITIES
MINNESOTA STATE STATUTE 16B.61 Subd.la
MUNICIPALITY, circle one(city,county,township)
Oman, Lyle Edward
City of Orono Date: 9/26/01
Box 66g�
Crystal Bay MN 55323
PROJECT: Orono - ISD #0278/Dist. Office Remodel
LOCATION: City of Orono
COUNTY: Hennepin
DESCRIPTION: Interior Remodel & Renovation
ADDRESS: 685 old Crystal Bay Road North
*****************************************
* ASSIGNED PROJECT NUMBER: 20010435 Date Received: 9/26/01
*****************************************
This letter shall serve as a contractual agreement pursuant to Minnesota Statute
16B.61 Subd.l a, between City of Orono and the
Commissioner of Administration for transfer of State Building Code
administration from the Minnesota Department of Administration to the
municipality for the "Public Building" or "State Licensed Facility" project
described in this agreement.
THIS AGREEMENT MUST BE RETURNED WITHIN 15 WORKING DAYS.
Building Codes and Standards Division,408 Metro Square Building, 121 7th Place East,St.Paul,MN 55101-2181
Voice: 651.296.4639,Fax: 651.297.1973;TTY: 1.800.627.3529 and ask for 296.9929
Department of Administration
Project: Orono - ISD#0278/Dist. Office Remodel Project#: 20010435
Description: Interior Remodel &Renovation
Location: City of Orono
1. Duties of Municipality. Please check the duties you are willing to contract(a,b or c).a or b must be initialed
by State Building Official.
a. Attend to all aspects of State Building Code administration,including:
1. Preliminary plan review with Building Codes and Standards Division Plan Review Staff when
required as checked by the Division.
2. Plan Review of building and grounds with written municipal plan review comments and designers
responses.
3. Interpretation,application,and enforcement of all code provisions.
4. Issuance of all permits and maintenance of all records.
5. Documentation on file of all equivalences and modifications to code as
required by UBC 104.2.7 and 104.2.8.
6. Adherence to all applicable written Division Plan Review Policies.See
www.state.mn.us/ebranch/admin/buildingcodes or contact the Division for list and copy of policies.
7. Issuance of certificate of occupancy with a copy informing the State Building Official when
services are completed.
b. Attend only to all required inspections including:
1. Issuance of all permits and maintenance of all records.
2. Perform all required inspections.
3. Issuance of certificate of occupancy with a copy informing the State Building Official when
services are completed.
c. Municipality will not be administering the building code for this project.
2. All costs of building code administration shall be as prescribed by Minnesota Statute 16B.61 Subd.Ia.
IN WITNESS WHEREOF,the parties have caused this agreement to be duly executed intending to be bound
thereby.
APPROVED: APPROVED:
IzRk QW411-- !a-r -o1
BUILD&G OFFICIAL DATE STATE BUILDING OFFICIAL DATE
APPROVED:
PaFormAG Page: 2
MUNICIPAL MANAGER/ADMINISTRATOR DATE
Building Codes and Standards Division,408 Metro Square Building, 1217th Place East,St.Paul,MN 55101-2181
Voice:651.296.4639,Fax:651.297.1973;TTY: 1.800.627.3529 and ask for 296.9929
,:35 FAX 651 223 5646 _ ROLD ARCHITECTS 1a002/002
'1
INITIAL APPLICATION FOR PLAN RE
VIE
4H but this application and return it to the Building Codes and Standards Division,approximatcl four(4)
weeks prior to.your expected plan review submittal. Failure to submit this form may result in up to a three(3)
week
delay-in the processing of the plan review appiication. This initial application will help us expeclite your
rev�e�x►.
?. l+*gjectTitie �,��.j .�r A t;ort7erdotionVn2uation
1' SIxAd'disss � 0110 `.�``�VV� I'D Townslrio
E CirYl Stade,Zip �+rlirl is j rCowry
i
Owner's Contact Per..an
1 Owner Address
�►t+� - • o,;�Ptro,x (�tSZ:) y"19r . ��•�
City.5taee,Zip State Agency(WAppliaable)
1 i I
'Owls"Firm
Firm Conine!Person
� '_ i Firm Address �,r�� �l
� fir -. I Phone
. j i City,Ststw Zip F t'j �
a. �''�M• to2. c Gyp
T ZZ3lt;�
10 Public(state)building paid for by the state or other state agency as a: D.State Cotlege D Zoo i ❑T .O.T. M D-N.R
.� O Statq Uaiversity O National Guard U State Hospital• O Stale Home. O Capita]Complex
Q Atb=specify
.$1 PubUc achooi distrigt building of$100,009 or more In construction cost.
Vt r O State Licensed Facijity licensed as a: Gl Hospital Q Nursing Home O Correctional Facility
. = O Supervisgd Living Facility 0 Free-standing Outpatienr$apgical Center
�Pe? : Q 00:ipr;specify
i ;fl New Building Construction C1 Addition �emodelirlg � O Otllei:Specify. i
USC Oempaocy Ciassificatiou(s): UBC Type of Construction:
=ka� :Project Dqscriptioa: 1641o� y''1G�D
C5l 10• 1St• [Cp ..
Total Projeeftd Construction Valuation'
Upo1
n recei�+' the completed initial application we will confirm that we are
the propor jurisdiction fo=the
Pro�je�t,i assign it a projecenumber for tracking and determine if the city./mu nicipnlity will do the plias raview,
thc(irispections,both or neither. we will notify you of the pro3ect number,where to submit your documents for
review aad.lioiv the inspections will be handled. if delegated to the city/mvmicipality,you will only Abed to
follow their piocedures and fee schedule. If your submittal is to the•BCSD, our standard npplieation process
wild Reed to�c followed. �
;I Hereby ac ow hat t 1 a is tion is not a Building Permit,nor does itautho)*e the start ofconsr,•rrcdon.
Apli t S se ; Pate
B 1 g Codes spd 5taridards Division,408 Metro Square Isuildbig, 121 7"Place East,St.Paul,MN 55101-2131
Voice:651.296.4639: F=6$1297.1973; TTY: 1.800.627.3529 and ask for 296.9929
I '
J
CITY OF ORONO CALLED IN DATE TIME
INSPECTION TIC SCHEDULED
PERMIT N0. Jam' COMPLETED =
ADDRESS �; -
OWNER rr __ CONTR.
TELEPHONE NO. W �oZ LP $S 6So
DESCRI ON /�C/Yh�1kV
FOOTING 11 MECHANICAL RI 18 EXCAWGRADING/FILLING
Q 02 FRAMING 13 MECHANICAL FINAL 19 LAKESHORE/WETLANDS
y 03 INSULATION 24/25 WOOD BURNER/FIREPLACE 34 TREE REMOVAL
Z 04 WALL BD. 12 WATER HOOK-UP 17 SITE INSPECTION
Q 05 FINAL 14 SEWER HOOK-UP 06 PROGRESS
07 DEMO-SITE 27 SEPTIC MAINT. 21 COMPLAINT
v 07 DEMO-FINAL 15 SEPTIC INSTALL. 22 FOLLOW-UP
09 PLUMBING RI 23 SEPTIC FINAL 35 HARD COVER REMOVAL
v 10 PLUMBING FINAL 36 FOUNDATION/REMOVAL
OWNER/CONTRACTOR TO ME OU:_YES 0
COMMENTS:
ccW
a
W
cc
Q
2
W
z
W
cc
j QwO1FIRECT
d
WRK SATISFACTORY:PROCEED ❑ PROJECTCOMPLETE
W WORK&PROCEED C1ISSUE CERTIFICATE OF OCCUPANCY
Q ❑CORRECT WORK,CALL FOR REINSPECTION TEMPORARY
C1 BEFORE COVERING PERMANENT
❑CORRECT UNSAFE CONDITION WITHIN HOURS. ❑ PHOTO TAKEN
INSPECTOR WILL RETURN ❑CITATION ISSUED
❑STOP ORDER POSTED.CALL INSPECTOR
❑ INSPECTION REQUIRED.CALLTO ARRANGE ACCESS.
Call for the next inspection 24 hours in advance. (952) 249-4600
OwnedCogtr Geste:
Inspector.
White Copy/Inspector's File Canary Copy/Site Notice
DATE TIME
CITY OF ORONO CALLED IN C
INSPECTION NOT E SCHEDULED I
PERMIT NO. bLIS L-11 COMPLETED
ADDRESS �[�J () icy CSN S fns
OWNER CONTR. o (� 21/IZOW 61dr
TELEPHONE NO. L� _6 95—,�53t
DESCRIPTION- 7r�
01 FOOTING 11 MECHANICAL RI 18 EXCAWGRADING/FILLING
Q 02 FRAMING 13 MECHANICAL FINAL 19 LAKESHORE/WETLANDS
y 03 INSULATION 24/25 WOOD BURNER/FIREPLACE 34 TREE REMOVAL
Z 04 WALL BD. 12 WATER HOOK-UP 17 SITE INSPECTION
Q 05 FINAL 14 SEWER HOOK-UP 06 PROGRESS
07 DEMO-SITE 27 SEPTIC MAINT. 21 COMPLAINT
v 07 DEMO-FINAL 15 SEPTIC INSTALL. 22 FOLLOW-UP
? 09 PLUMBING RI 23 SEPTIC FINAL 35 HARD COVER REMOVAL
v 10 PLUMBING FINAL 36 FOUNDATION/REMOVAL
OWNER/CONTRACTOR TO MEET YOU YES—NO
COMMENTS:
W
J
O /
0
LL
W
cc
Q
Z
W
z
W
cc
0 3,
d
W O'WORKSATISFACTORY.PROCEED ❑ PROJECTCOMPLETE
W !❑CORRECT WORK&PROCEED ❑ ISSUE CERTIFICATE OF OCCUPANCY
❑CORRECT WORK,CALL FOR REINSPECTION TEMPORARY
BEFORECOVERING PERMANENT
❑CORRECT UNSAFE CONDITION WITHIN HOURS. ❑ PHOTO TAKEN
INSPECTOR WILL RETURN ❑CITATION ISSUED
❑STOP ORDER POSTED.CALL INSPECTOR
❑INSPECTION REQUIRED.CALL TO ARRANGE ACCESS.
Call for the next inspection 24 hours in advance. (952) 249-4600
Owner/contr for on site:
n
Inspector. 1
White Copylinspector's File Canary Copy/Site Notice
v\�Q'{/` DATE TIME
CITY OF ORONO CALLED IN
INSPECTION NOTICE SCHEDULED
PERMIT NO. COMPLETED K
ADDRESS �v D�o� K V e .
OWNER 1920ANQ IC-A00(_ CONTR. ���
TELEPHONE NO. 431 ' 4( D lJ 9 6e-7 _ /-�la-,
DESCRIPTION
01 FOOTING 11 ME6fiANICALRI 18 EXCAV/GRADING/FILLING
Q 02 FRAMING 13 MECHANICAL FINAL 19 LAKESHORE/WETLANDS
LI03 INSULATION 24/25 WOOD BURNER/FIREPLACE 34 TREE REMOVAL
Z 04 WALL BD. 12 WATER HOOK-UP 17 SITE INSPECTION
Q 05 FINAL 14 SEWER HOOK-UP 06 PROGRESS
07 DEMO-SITE 27 SEPTIC MAINT. 21 COMPLAINT
07 DEMO-FINAL 15 SEPTIC INSTALL. 22 FOLLOW-UP
09 PLUMBING RI 23 SEPTIC FINAL 35 HARD COVER REMOVAL
v 10 PLUMBING FINAL 36 FOUNDATION/REMOVAL
Z OWNERICONTRACTOR TO MEET YOU:_YES_NO
COMMENTS:
a
0
0
2
W
cc
e
z
W
W
cc
J
d
U ORKSATISFACTORY:PROCEED ❑PROJECT COMPLETE
❑CORRECT WORK&PROCEED ❑ISSUE CERTIFICATE OF OCCUPANCY
C ❑CORRECT WORK,CALL FOR REINSPECTION TEMPORARY
V BEFORECOVERING PERMANENT
❑CORRECT UNSAFE CONDITION WITHIN HOURS. ❑PHOTO TAKEN
INSPECTOR WILL RETURN ❑CITATION ISSUED
❑STOP ORDER POSTED.CALL INSPECTOR
❑INSPECTION REQUIRED.CALLTO ARRANGE ACCESS.
Call for the next inspection 24 hours in advance. (952) 249-4600
Owner/Contractor 0 it
Inspector.
White Copy/Inspector's File Canary Copy/Site Notice
DATE TIME
CITY OF ORONO CALLED IN
INSPECTION N076E SCHEDULED
PERMIT NO. S� COMPLETED
ADDRESS S '
OWNERS <- CONTR.
TELEPHONE NO.
DESCRIPTION
Qj 01 FO ING 11 MECHANICAL RI 18 EXCAV/GRADING/FILLING
13 MECHANICAL FINAL 19 LAKES HORE/WETLANDS
Q 03 INSULATION 24/25 WOOD BURNER/FIREPLACE 34 TREE REMOVAL
-f 04 WALL BD. 12 WATER HOOK-UP 17 SITE INSPECTION
Q 05 FINAL 14 SEWER HOOK-UP 06 PROGRESS
07 DEMO-SITE 27 SEPTIC MAINT. 21 COMPLAINT
07 DEMO-FINAL 15 SEPTIC INSTALL. 22 FOLLOW-UP
Q
i09 PLUMBING RI 23 SEPTIC FINAL 35 HARD COVER REMOVAL
J 10 PLUMBING FINAL 36 FOUNDATION/REMOVAL
OWNERICONTRACTOR TO MEET YOU: YES NO
S' COMMENTS:
LU
Q.
cc G
d
O
cc
O
W
CC
Q
Z
W
W
cc
WyJjWORK SATISFACTORY:PROCEED ❑ PROJECT COMPLETE
//[I CORRECT WORK&PROCEED
W ❑ ISSUE CERTIFICATE OF OCCUPANCY
O ❑CORRECT WORK,CALL FOR REINSPECTION TEMPORARY
C) BEFORE COVERING PERMANENT
❑CORRECT UNSAFE CONDITION WITHIN HOURS.
❑ PHOTO TAKEN
INSPECTOR WILL RETURN
❑STOP ORDER POSTED.CALL INSPECTOR ❑CITATION ISSUED
❑ INSPECTION REQUIRED.CALL TO ARRANGE ACCESS.
Call for the next inspection 24 hours in advance.473-7357
OwnerlContl' r on site:
Inspector. �����
White Copyllnspector's File Canary Copy/Site Notice
DATE TIME
CITY OF ORONO t7 qV!CALLED IN —
INSPECTION NOTICE (( 1 SCHEDULED �1 4 0;2_
PERMIT NO. COMPLETED
ADDRESS lea
OWNER J61116w CONTR.
TELEPHONE N0.
DESCRIPTION
t4 01 FOOTING 11 MECHANICAL RI 18 EXCAWGRADING/FILLING
Q 02 FRAMING 13 MECHANICAL FINAL 19 LAKESHORE/WETLANDS
" 03 INSULATION 24/25 WOOD BURNER/FIREPLACE 34 TREE REMOVAL
Q
Z 04 12 WATER HOOK-UP 17 SITE INSPECTION
05 FINAL 14 SEWER HOOK-UP 06 PROGRESS
MO-SITE 27 SEPTIC MAINT. 21 COMPLAINT
v 07 DEMO-FINAL 15 SEPTIC INSTALL. 22 FOLLOW-UP
09 PLUMBING RI 23 SEPTIC FINAL 35 HARD COVER REMOVAL
J 10 PLUMBING FINAL 36 FOUNDATION/REMOVAL
OWNERICONTRACTOR TO MEET YOU:_YES_NO
Zt
o COMMENTS:
W
C
c
J
O
a
cc
O
LL
w
C
Q
Z
W
Z
W
rr-
Z1
O �, �
�
WQ Cp.WORK SATISFACTORY:PROCEED 21PROJECT COMPLETE
W ❑CORRECT WORK&PROCEED 01SSUE CERTIFICATE OF OCCUPANCY
Q ❑CORRECT WORK,CALL FOR REINSPECTION TEMPORARY
BEFORE COVERING
PERMANENT
❑CORRECT UNSAFE CONDITION WITHIN HOURS. ❑ PHOTO TAKEN
INSPECTOR WILL RETURN
ElSTOP ORDER POSTED.CALL INSPECTOR ❑CITATION ISSUED
❑INSPECTION REQUIRED.CALL TO ARRANGE ACCESS.
Call for the next inspection 24 hours in advance. (952) 249-4600
Owner/Contracto
Inspector.
White Copy/Inspector's File Canary Copy/Site Notice