HomeMy WebLinkAbout2011 - 01470 - duct work CITY OF ORONO PERMIT NO.: 2011-01470
2750 KELLEY PARKWAY
ORONO, MN 55356- DATE ISSUED: 11123/2011
(952) 249-4600 FAX: (952)249-4616
ADDRESS : 1299 WILDHURST TR
PIN : 07-117-23-31-0031
LEGAL DESC : TONKAVIEW GARDENS
: LOT 046 BLOCK 000
PERMIT TYPE : MECHANICAL(<$500)
PROPERTY TYPE : RESIDENTIAL
CONSTRUCTION TYPE : DUCT WORK
NOTE: RUNNING DUCTWORK FROM EXISTING FURNACE
APPLICANT MECHANICAL(<$500) 15.00
SCHIMMEL ETAL,PATTI STATE SURCHARGE MECH(<$500) 5.00
1299 WILDHURST TRAIL TOTAL 20.00
MOUND,MN 55364-
OWNER
SCHIMMEL ETAL,PATTI
1299 WILDHURST TRAIL
MOUND,MN 55364-
AGREEMENT AND SWORN STATEMENT
The work for which this permit is issued shall be performed according to
the approved plans and specifications,applicable City approvals,and the
State Building Code. This permit is for only the work described and does
not grant permission for additional or related work which requires separate
permits. All provisions of laws and ordinances goveming this type of work
shall be compied with whether or not specified herein.This permit will
expire and become null and void if construction authorized is not
commenced within 180 days of the date of issuance,or if construction is
suspended for a period of 180 days at any time after work has commenced.
The applicant is responsible for assuring all required inspections are
requested in conformance with the State Building Code.This permit may be
revoked at any time for due cause.
//' ( ( 9k1A-4-11
// //
Applicant Permitee Signature Date Issued Signature Date
SEPARATE PERMITS REQUIRED FOR WORK OTHER THAN DESCRIBED ABOVE.
. FOR ITY SE ONLY
City of Orono f
Og PO.Box 66 Date Received: f Permit# 2O f!- ('�/L/7
'� 2750 Kelley Parkway
tor
Crystal Bay,MN 55323Approved By: Amount$:02r
Phone(952)249-4600 Fax(952)249-4616
CITY OF ORONO-MECHANICAL PERMIT
(All Commercial permits must be approved by the Building Official or Inspector and/or Fire Marshall)
GENERAL INFORMATION
1. You may apply for mechanical permits by mail or in person at the City offices. Applications will
be reviewed and a permit will be issued within two working days.
2. Permit cards will be sent by return mail after a review is completed. PERMITS ARE NOT
VALID UNTIL YOU RECEIVE A PERMIT. WORK MUST NOT BEGIN UNTIL THE
PERMIT CARD IS POSTED ON THE JOB SITE.
3. Mechanical Designs-Complete calculations,details and specifications are required for each
heating,ventilation,humidification-dehumidification, and air conditioning installation including
heat loss/heat gain calculation,design temperatures, equipment ratings and identification as to
type,manufacturer and model. Data shall be presented on form provided.
4. When 4ny new construction or remodeling is involved, a separate building permit must be
obtaiuied.
5. All work must be done in accordance with the Uniform Mechanical Code/State Building Code
requirements.
6. All work must be inspected(rough-in and final). Call(952)249-4600.
(24-48 hour notice required)
7. House Heating Test Record must be submitted before final.
TYPE OF PERMIT
(Check All That Apply)
NI Residential ❑ Commercial(Approval Required)
❑ New ❑Additional ❑ Repairs ❑ Replace
Job Site/Owner Information:
Site Address: ) 2. 99 w 1J k uY S,-r
Owner: Ji /- ( Mailing Address: /c .- 1c
, 5-r to`-j (,o
City: 1.-.,;v��� L j?ct. Zip: S 6 0
Home Phone: 7 �} .�( -� 'S O(G�Alternate Phone: d 2c.)— 3617
Contractor Information:
Contractor: +i G iVi C.. O W t � Contact Person: T caf Sc t_,rvt%v-.
Address: State Bond#:
City: Zip: Expiration Date:
Phone: Alternate Phone: LCi - z �" G, I F
Insurance-Current:
1
a
Note: All Geothermal Systems will now require a Site Plan&Review by our Building Official.
IS THIS GEOTHERMAL? ❑ Yes WNo
HEATING SYSTEMS
Quantity:
Make:
Model:
Fuel:
Flue Size:
Input BTUs:
Output BTUs:
CFM:
COOLING SYSTEMS
Quantity:
Make:
Model:
Tons:
H.Power
FIREPLACES
❑ Gas Factory Fireplace Brand Name:
❑ Wood Burning Fireplace
❑ Wood Stove Model No.:
❑ Wood Stove with Flue/Masonry
VENTILATION
❑ No. Kitchen Exhaust duct recirculating cfm
❑ No. Bath Exhaust(must have duct outside) cfm
❑ No. Other Fans: Locations cfm
FUEL STORAGE (Must be approved by Fire Marshall if proposing to abandon tank in place.)
❑ Installation ❑ Removal
Fuel Oil: gallons E Underground ❑ Inside ❑ Outside
LP Gas: gallons
Other:
GAS LINE ONLY
❑ Outdoor Grill ❑ Other/List What&Where:
2
�C '� (A)0 C-- O- Z�`►� Esc„ u rig c C-2
:3�^w,"m ...�;a� a '.�.s . .a
Yes,this section applies
The replacement of a Residential fixture or appliance that meets all three of the following requirements:
1. Does not require modification to electrical or gas service.
2. Has a total cost of$500.00 or less;excluding the cost of the fixture or appliance: and
3. Is improved,installed or replaced by the homeowner or licensed contractor.
Skip next section,if this applies; Cost of Permit $ 15.00
State Surcharge $ 5.00
Mail-In Fee(If Applicable) $ 2.00
Total Permit Fee $
a. 2-. «;: V ,, F ,:rii- Av
,. s . a� `6 0 11
0 .11,6:0.1:05.20,01A
If above does not apply;follow guidelines below:
1. CONTRACT PRICE *is 1.25%of contract price with a(Minimum Fee of$50.00)
x.0125$
(contract price) (minimum$50.00)
2. STATE SURCHARGE
x .0005 S
(contract price)
3. POSTAGE&HANDLING(Only on Mail-In Applications) $ 2.00
4. TOTAL PERMIT FEE(Add Lines 1-3 Above) $
■ * CONTRACT PRICE or JOB COST means the actual or estimated dollar amount charged for the
permitted work including materials, labor, profit, and other fixed costs. It is the amount to be charged
to the customer for the work done. If any material, equipment, labor or installations are furnished by
the owner, tenant or any other party, the reasonable market value of such items must be added to the
estimated cost or contract price for permit fee purposes. In the event that there is a dispute on the
amount of the job cost, the City may request the submission of a signed copy of the actual contract.
p pp "rtrt` .�c a paa' i ,r '"
�L1m t9C ':
� a ; a,: u-'...
The undersigned hereby applies to the City for issuance of a Mechanical Permit, agrees to do all
work in strict accordance with the ordinances of the City and the regulations of the State of
Minnesota, and certifies that all statements made on this application are complete, true and
correct.
Applicant's Signature: / 6— - 4 - j'� �:' Date: / ( – 22
3
. ,
I I
fr" r'4 r LAti (.-,(,14 0.(
...f_ s•-.J ,L'
• \--ci-f-vtc- vl L,,,,p SJqt r
r
St t t t ,---
'--)
L&
_ . ...
_.
- 1-. N,.) .. _
C,
_1-: --1 1 --Z_
A t_ N.,.-- , , , ,1
, • /1
3'‘,(k ti 7 , ', '.: J ./.. 12 Tr)t) t,,,/ i 1 S -164 I—
,c‘ ,--c... _..---
,, ...._......
VA -.) ' '-c _, , ____..- ..... _ „ •-,„
_ . ..
t t I i
l iQ /
t---, 1 ' .... ,,, a
i 1
/ ,-` ''.+. 0,( il . e. .„ -.." •,,,1 4'. (,) i ,e\
...,
-,--., „-
-..-'
11
,C \'' - ,
r17-71 t ,..; •
C, '-'
-.) . . ,....
„.„---.
0 REScheck Software Version 4.4.1
Compliance Certificate
Project Title: Todd Schimmel
Energy Code: 2009 IECC
Location: Orono,Minnesota
Construction Type: Single Family
Project Type: Addition/Alteration
Heating Degree Days: 8037
Climate Zone: 6
Construction Site: Owner/Agent: Designer/Contractor:
1299 Wildhurst Trail todd Schimmel Harry Nasset
Orono,MN 55364 1299 Wildhurst Trail Design Services
Permit#612 282-6618 Orono,MN 55364 4154 Shoreline Drive
612 282-6618 Spring Park,MN 55384
952 401-8515
Compliance: Passes
Compliance:16.5%Better Than Code Maximum UA:109 Your UA:91
The%Better or Worse Than Code index reflects how close to compliance the house is based on code trade-off rules.
It DOES NOT provide an estimate of energy use or cost relative to a minimum-code home.
Gross Cavity Cont. Glazing UA
Assembly Area or R-Value R-Value or Door
Perimeter U-Factor
Ceiling 1:Raised or Energy Truss 270 48.8 31.8 3
Wall 1:Wood Frame, 16"o.c. 791 21.1 8.9 22
Window 1:Vinyl Frame:Double Pane with Low-E 83 0.350 29
Door 1:Solid 105 0.340 36
Basement Wall 1:Masonry Block with Empty Cells 32 15.1 6.7 1
Wall height:8.0'
Depth below grade:7.3'
Insulation depth:8.0' .
Compliance Statement: The proposed building design described here is consistent with the building plans,specifications,and other
calculations submitted with the permit application.The proposed building has been designed to meet the 2009 IECC requirements in
REScheck Version 4.4.1 and to comply with the mandatory requirements 'sted in the REScheck Inspection Checklist.
/Z7/1: -_,e__.V) e•.1" -d-2 <---- - /:_-2t4--;>------ - t I.A,x)
Name-Titl'e Signature Date
•
Project Title: Todd Schimmel Report date: 11/11/11
Data filename: Untitled.rck Page 1 of 4
CilREScheck Softwarection Version 4.4i.1
Ceilings: Inspe
Ceilings:
❑ Ceiling 1:Raised or Energy Truss,R-48.8 cavity+R-31.8 continuous insulation
Comments:
Insulation must achieve full height over the plate lines of exterior walls.
Above-Grade Walls:
❑ Wall 1:Wood Frame, 16"o.c.,R-21.1 cavity+R-8.9 continuous insulation
Continuous insulation specified for this above-grade wall has consistent R-value rating across full area of the wall.
Comments:
Basement Walls:
❑ Basement Wall 1:Masonry Block with Empty Cells,8.0'ht/7.3'bg/8.0'insul,R-15.1 cavity+R-6.7 continuous insulation
Comments:
Windows:
❑ Window 1:Vinyl Frame:Double Pane with Low-E,U-factor:0.350
For windows without labeled U-factors,describe features:
#Panes Frame Type Thermal Break? Yes No
Comments:
Doors:
❑ Door 1:Solid,U-factor:0.340
Comments:
Air Leakage:
❑ Joints(including rim joist junctions),attic access openings,penetrations,and all other such openings in the building envelope that are
sources of air leakage are sealed with caulk,gasketed,weatherstripped or otherwise sealed with an air barrier material,suitable film or
solid material.
❑ Air barrier and sealing exists on common walls between dwelling units,on exterior walls behind tubs/showers,and in openings between
window/door jambs and framing.
❑ Wood-burning fireplaces have gasketed doors and outdoor combustion air.
❑ Automatic or gravity dampers are installed on all outdoor air intakes and exhausts.
❑ Recessed lights in the building thermal envelope are 1)type IC rated and ASTM E283 labeled and 2)sealed with a gasket or caulk
between the housing and the interior wall or ceiling covering.
❑ Access doors separating conditioned from unconditioned space are weather-stripped and insulated(without insulation compression or
damage)to at least the level of insulation on the surrounding surfaces.Where loose fill insulation exists,a baffle or retainer is installed
to maintain insulation application.
Air Sealing and Insulation:
❑ Building envelope air tightness and insulation installation complies by either 1)a post rough-in blower door test result of less than 7
ACH at 33.5 psf OR 2)the following items have been satisfied:
(a)Air barriers and thermal barrier:Installed on outside of air-permeable insulation and breaks or joints in the air barrier are filled or
repaired.
(b)Ceiling/attic:Air barrier in any dropped ceiling/soffit is substantially aligned with insulation and any gaps are sealed.
(c)Above-grade walls:Insulation is installed in substantial contact and continuous alignment with the building envelope air barrier.
(d)Floors:Air barrier is installed at any exposed edge of insulation.
(e)Plumbing and wiring:Insulation is placed between outside and pipes.Batt insulation is cut to fit around wiring and plumbing,or
sprayed/blown insulation extends behind piping and wiring.
(f) Corners,headers,narrow framing cavities,and rim joists are insulated.
Project Title:Todd Schimmel Report date: 11/11/11
Data filename: Untitled.rck Page 2 of 4
(9)Shower/tub on exterior wall:Insulation exists between showers/tubs and exterior wall.
Sunrooms:
❑ Sunrooms that are thermally isolated from the building envelope have a maximum fenestration U-factor of 0.50 and the maximum
skylight U-factor of 0.75.New windows and doors separating the sunroom from conditioned space meet the building thermal envelope
requirements.
Materials Identification and Installation:
o Materials and equipment are installed in accordance with the manufacturer's installation instructions.
❑ Insulation is installed in substantial contact with the surface being insulated and in a manner that achieves the rated R-value.
• Materials and equipment are identified so that compliance can be determined.
• Manufacturer manuals for all installed heating and cooling equipment and service water heating equipment have been provided.
D Insulation R-values and glazing U-factors are clearly marked on the building plans or specifications.
Duct Insulation:
• Supply ducts in attics are insulated to a minimum of R-8.All other ducts in unconditioned spaces or outside the building envelope are
insulated to at least R-6.
Duct Construction and Testing:
❑ Building framing cavities are not used as supply ducts.
D All joints and seams of air ducts,air handlers,filter boxes,and building cavities used as return ducts are substantially airtight by means
of tapes,mastics,liquid sealants,gasketing or other approved closure systems.Tapes,mastics,and fasteners are rated UL 181A or
UL 181B and are labeled according to the duct construction.Metal duct connections with equipment and/or fittings are mechanically
fastened.Crimp joints for round metal ducts have a contact lap of at least 1 1/2 inches and are fastened with a minimum of three
equally spaced sheet-metal screws.
Exceptions:
Joint and seams covered with spray polyurethane foam.
Where a partially inaccessible duct connection exists,mechanical fasteners can be equally spaced on the exposed portion of the
joint so as to prevent a hinge effect.
Continuously welded and locking-type longitudinal joints and seams on ducts operating at less than 2 in.w.g.(500 Pa).
U All ducts and air handlers are located within conditioned space.
Heating and Cooling Equipment Sizing:
❑ Additional requirements for equipment sizing are included by an inspection for compliance with the International Residential Code.
D For systems serving multiple dwelling units documentation has been submitted demonstrating compliance with 2009 IECC Commercial
Building Mechanical and/or Service Water Heating(Sections 503 and 504).
Circulating Service Hot Water Systems:
• Circulating service hot water pipes are insulated to R-2.
• Circulating service hot water systems include an automatic or accessible manual switch to turn off the circulating pump when the
system is not in use.
Heating and Cooling Piping Insulation:
❑ HVAC piping conveying fluids above 105 degrees F or chilled fluids below 55 degrees F are insulated to R-3.
Swimming Pools:
o Heated swimming pools have an on/off heater switch.
D Pool heaters operating on natural gas or LPG have an electronic pilot light.
❑ Timer switches on pool heaters and pumps are present.
Exceptions:
Where public health standards require continuous pump operation.
Where pumps operate within solar-and/or waste-heat-recovery systems.
• Heated swimming pools have a cover on or at the water surface. For pools heated over 90 degrees F(32 degrees C)the cover has a
minimum insulation value of R-12.
Exceptions:
Covers are not required when 60%of the heating energy is from site-recovered energy or solar energy source.
Lighting Requirements:
❑ A minimum of 50 percent of the lamps in permanently installed lighting fixtures can be categorized as one of the following:
(a)Compact fluorescent
Project Title: Todd Schimmel Report date: 11/11/11
Data filename: Untitled.rck Page 3 of 4
(b)T-8 or smaller diameter linear fluorescent
(c)40 lumens per watt for lamp wattage<=15
(d)50 lumens per watt for lamp wattage>15 and<=40
(e)60 lumens per watt for lamp wattage>40
Other Requirements:
❑ Snow-and ice-melting systems with energy supplied from the service to a building shall include automatic controls capable of shutting
off the system when a)the pavement temperature is above 50 degrees F,b)no precipitation is falling,and c)the outdoor temperature is
above 40 degrees F(a manual shutoff control is also permitted to satisfy requirement'c').
Certificate:
D A permanent certificate is provided on or in the electrical distribution panel listing the predominant insulation R-values;window
U-factors;type and efficiency of space-conditioning and water heating equipment.The certificate does not cover or obstruct the visibility
of the circuit directory label,service disconnect label or other required labels.
NOTES TO FIELD:(Building Department Use Only)
Project Title:Todd Schimmel Report date: 11/11/11
Data filename: Untitled.rck Page 4 of 4
2009 IEencyCC Energy
EfficiCertificate
Insulation Rating R-Value
Ceiling/Roof 80.60
Wall 29.98
Floor/Foundation 21.84
Ductwork(unconditioned spaces):
Glass& Door Rating U-Factor SHGC
Window 0.35
Door 0.34 NA
Heating &Cooling Equipment Efficiency
Heating System:
Cooling System:
Water Heater:
Name: Date:
Comments:
& // j 5` D E TIME
CITY OF ORONO CALLED IN
INSPECTION NOTICE SCHEDULED '
PERMIT NO.ao//—v 59 /COMPLETED
ADDRESS/"' 99 �d-dh�-t
ka- 7 '
OWNER ri-C TELEPHONE NO. 6/2- 735 3357
CONTRACTOR A,�
DESCRIPTION kra-e AfeJLJ
❑ FOOTING ❑ PLUMBING FINAL ❑ EXCAV/GRADING/FILLING
Q 0 POURED WALL ❑ MECHANICAL RI 0 LAKESHORE/WETLANDS
ti 0 FRAMING ❑ MECHANICAL FINAL
❑ TREE REMOVAL
• ❑ INSULATION 0 WOOD BURNER/FIREPLACE 0 SITE INSPECTION
Q 0 RADON SLAB 0 WATER HOOK-UP ❑ PROGRESS
❑ FINAL ❑ SEWER HOOK-UP ❑ COMPLAINT
v ❑ DEMO-SITE ❑ SEPTIC MAINT. ❑ FOLLOW-UP
? ❑ DEMO-FINAL ❑ SEPTIC INSTALL 0 HARD COVER REMOVAL
v ❑ PLUMBING RI ❑ SEPTIC FINAL ❑ FOUNDATION/REMOVAL
OWNER/CONTRACTOR TO MEET YOU:_YES_NO
o COMMENTS:
W
CC
O
CC
O
LL
W
CC
coW
W
Cc
IK SATISFACTORY:PROCEED ❑ PROJECT COMPLETE
CC
❑CORRECT WORK&PROCEED ❑ ISSUE CERTIFICATE OF OCCUPANCY
▪ ❑CORRECT WORK,CALL FOR REINSPECTION TEMPORARY
U BEFORE COVERING PERMANENT
❑CORRECT UNSAFE CONDITION WITHIN HOURS. ❑ PHOTO TAKEN
INSPECTOR WILL RETURN
CI CITATION ISSUED
CISTOP ORDER POSTED.CALL INSPECTOR
❑ INSPECTION REQUIRED.CALL TO ARRANGE ACCESS.
Call for the next inspection 24 hours in advance. (952) 249-4600
Owner/Contractor ons•e: i`.�
Inspector. ril7 7
White Copy/Inspector's File Canary Copy/Site Notice