HomeMy WebLinkAboutfire system plan � BOSCH
D9412GV3 Battery Calculator Date:7l1/2010
Calculations for 12 VDC Devices only
Instructions:Add appropriate information in shaded data fields
Device Quantity of Standby mA Alarm mA Total Device Total Device
Descri tion Devices Per Device Per Device Standb mA Alarm mA
Bosch D9412GV31D7412GV3 1 225 300 225 300
D113 Batte Lead Su ervision Module 0 31 31 0 0
D125B Two wire Smoke Detector Interface Module 0 22 150 0 0
D127 Reversin Rela 0 5 55 0 0
D129 Class A Interface Module 0 22 23 0 0
D130 Rela Module 0 0 50 0 0
D185 Reverse Polarit Si nalin Module 0 245 300 0 0
D192C NAC Su erviso Module Class B 0 25 50 0 0
D192G NAC Su erviso Module Class B 1 35 100 35 100
D1255 AI ha Numeric Ke ad 0 106 206 0 0
D1256 Fire Command Center 1 106 206 106 206
D1257 Fire Annunciator 0 106 206 0 0
D1260 AI ha Numeric Ke ad 0 200 250 0 0
D275 Power Su ervision Rela 0 30 30 0 0
D720 LED Command Center 0 20 100 0 0
D8125 Po ex Module 0 50 50 0 0
D8125Mux Module 1 128 128 128 128
D8128D Octo o it 2 25 50 50 100
D8129 Octal Rela Module 0 20 200 0 0
D8130 Releasin Module 0 7 60 0 0
D928 Dual Phone Line Switcher 0 18 100 0 0
D9127T/U Po it 0 0.5 0.8 0 0
D9131A Printer Interface Module 0 21 23 0 0
D92106 Access Interface Module 0 110 110 0 0
DS7432 8 In ut Remote Module 0 10 10 0 0
DS7457i Mux Sin le Point In ut Module 9 0.5 0.5 4.5 4.5
DS7460i Mux Dual Point In ut Module 0 1 1 0 0
DS7465i Mux Sin le In/Out ut Module 0 1 1 0 0
DX4010i Serial Interface Module 0 50 55 0 0
DX4020 Ethernet Interface Module 1 135 135 135 135
SDI S litter ICP-SDI-9114 1 30 30 0 0
D7050 Photoelectric Smoke Detector 15 0.55 0.55 0 0
S stem Sensor 5601P Heat Detector 6 0 0 0 0
FMM-100SATK Pull Station 3 0 0 0 0
Add other devices 0 0 0
Add other devices 0 0 0
Add other devices 0 0 0
Total D9412GV2 S stem Current mA 683.5 973.5
Auxilia Alarm Devices 12VDC Horns/Strobes etc...
Add other devices 0 0 0
Add other devices 0 0 0
Add other devices 0 0 0
Add other devices 0 0 0
Add other devices 0 0 0
Add other devices 0 0 0
0 0 0
Summa Section 12VDC Standb Calculation
Standb Hrs.Re uired 24
Alarm Soundin Minutes 5
Total S stem Standb mA 0.6835
Total S stem Alarm mA 0.974
Total S stem Standb A/H 16.40
Total S stem Alarm A/H 0.081125
Min.A/H Batte Re uired 18.13
Battery Calculation Worksheet
Number of Stand-b Alarm
Device Devices Current per Device Current Current
For each device use this formula: This column x This column = Equals Current per number of devices.
AL602ULADA 1 Stand-by: 90mA 90mA
(Current draw from battery) A1arm: 175mA 175mA
A AL602 Current 90mA 175mA
Auxiliary Devices Refer to device manual for current ratings.
1n! E(oc�c �ac a/Sc > Alarm/Stand-by $Z mA p mA $Z mA
1•/ cE � 30� � Alarm/Stand-by /OZ � d mA G�p�mA
- @ � Z Alarm/Stand-by /y�'mA p mA �91p mA
B Auziliary Devices Current(must not exceed 1 amp)
Refer to device manual for current ratings.
WfF c� �° / � Z Alarm: �97 mA OmA 3qc{mA
ST� /Sc,� !.� Alarm: s7 mA OmA Z�g mA
� -/ / Alarm: /S Z mA omA /8"Z mA
Alarm: mA OmA mA
C Notification Appliances Current must not exceed 6.5 amp(6500mA) OmA mA
D Total alarm current 90 � �.���'
E Total current ratings converted to amperes(line D x .001) ��c,�o A �.'7bS A
F Number of standby hours (24 for NFPA 72, Chapter 1, 1-5.2.5). ZC.{ H
G Multiply lines E and F. Total stand-by AH Z �� AH
H Alarm sounding period in hours. •
(For example, 5 minutes= .0833 hours.) .v�33 H
I Multiply lines E and H. Total alarm AH ��y, �
J Add lines G and I. Total stand-by and alarm AH °�.3p"� AH
Multiply line J by 1.30.
K (30%extra insurance to meet desired performance) 3,v �
Total ampere -hours required
Units are capable of recharging 40AH battery max. If total ampere -hour required exceeds 40AH,
decrease AiJX current to provide enough stand-by time for the application.
AL602ULADA
-9-
i �
. � � • • '
' ��� BOSCH
�
Invented for life
D9412GV3 Control Panel
► Fully integrated intrusion,fire,and access control
allows users to interface with one system instead of
' ��--� three
' r ► Conettix IP-based communication options provide
_ high-speed,secure alarm transport and control through
connection of up to two wired (DX4020)and/or
�; � wireless(ITS-DX4020-G) network interfaces
i, .„�,3'
.. . , ,. . __ ► Eight programmable areas with perimeter and interior
� �� •- partitioning
�+� � q
�� � ► 246 points with flexible configuration options to meet
n� � � � � � multiple installation requirements
� i "� ► Commercial Wireless allows up to 238 RF points
�l ,� � ► Your choice of vacuum fluorescent or ATM style user
interface keypads
The D9412GV3 Control Panel delivers a powerful new System Response
solution for intrusion,access control,and fire alarm system • High-performance micro-controller provides
applications. The control panel includes a communicator industry-leading system response
that sends events to selected public switched telephone • 31 custom point indexes, including fire supervisory
• Selectable point response time
network(PSTN),IP network,or general packet radio service . Cross point capability
(GPRS) destinations through four programmable route . Fire alarm verification
groups.The control panel provides up to 246 individually . Fire inspector's local test
identified points. Each point: • Watch mode
• Accommodates normally-open (NO) and • Scheduled events (skeds) arm, disarm, bypass and
normally-closed (NC) devices with end-of-line (EOL) unbypass points,control relays,control authority levels,
resistor supervision
and control door access
• Is programmable for fire, fire supervisory, or intrusion User Interface
applications. • Supervision of up to eight keypads (up to 32
With the D9412GV3 you can: unsupervised keypads can be used)
• Monitor alarm points for intruder or fire alarms while • Custom keypad text is fully programmable, including
o eratin user ke remote programmingt
p g ypads and other outputs . Full function command menu including custom
• Program all system functions on-site through a D5200 functions
Programmer; locally or remotely through Remote . quthority by area and 16-character name for each user
Programming Software (RPS). 14 custom authority levels control user's authority to
• Add up to eight doors of access control using the • change, add, or delete passcodes or access control
optional D92106LC Access Control Interface Module. credentials; to disarm or bypass points; and to start
system tests
Functions
Programmable Outputs
• 2 A alarm power at 12 VDC
• 1.4 A auxiliary power at 12 VDC
• Four alarm-output patterns
• Programmable bell test
www.boschsecurity.com
� +
�•� • • '
Area Configurations Door-Activated Custom Function
Area programming offers a wide selection of different A custom function activates when user credentials are
system configurations. Each area is assigned an account presented to a D92106 door controller's reader.The
number to define annunciation, control, and reporting custom function behaves as though the user performed a
functions. Multiple areas can be linked to a shared area function at the keypad associated with the door controller.
which is automatically controlled (hallway or lobby).Area passcodes
arming can be conditional on other areas (master or User passcodes contain three to six digits.Assign each user
associate). Any area can be configured for perimeter and one of 14 customized authority levels in each area. Restrict
interior arming, not requiring a separate area for this passcodes to operate only during certain times.
function.
The Two Man Rule and Early Ambush options require two
Two Man Rule passcodes, providing additional security in financial
Two Man Rule provides added security by requiring: establishments such as banks.
• Two people present at opening Communications
• Two unique passcodes on the same keypad to disarm
an area The D9412GV3 Control Panel prioritizes and sends reports
Without the second passcode, the system denies entry. in Contact ID or Modem Illaz communications formats to
Early Ambush four route groups. Each group has a programmable primary
Early Ambush requires two passcode entries on the same and backup destination.
keypad. Enter the same passcode twice or have two unique The D9412GV3 provides flexible communications for most
passcodes, depending on the configuration.The first entry central stations with reporting capabilities such as:
disarms the area and the second entry stops a timer • Individual point numbers
programmed to send a duress event. If the second entry • Opening or closing reports by user and area number
does not occur within the programmed time,the system • Remote programming attempts
generates a duress event. Early Ambush allows users to • Diagnostic reports
The D9412GV3 uses the DX4020 Ethernet Network
inspect the premises and use the system to confirm that the Interface Module and/or the ITS-DX4020-G GPRS/GSM
area is safe to enter, providing added security.
Communicator to communicate with the Conettix D6600
Easy Exit Control and D6100i Communications Receiver/Gateways. Using
The D9412GV3 Control Panel changes from one armed state Conettix IP communication offers a secure path that
to another armed state without disarming. For example, if includes anti-replay/anti-substitution features and provides
you change the state from MasterArm to PerimeterArm,the enhanced security with encryption. Both the DX4020 and
control panel complies and reports the change. Easy Exit ITS-DX4020-G can be used for remote programming.
Control reduces the number of keystrokes, simplifying Security and Fire Detection
system operation. The D9412GV3 Control Panel provides eight on-board
Programmable Passcode-controlled Menu List points, and up to 238 additional off-board points
The system prompts users to enter a passcode prior to (depending on model and expansion interfaces).You can
viewing the keypad menu. The keypad display shows the program individual points to monitor all types of burglar
user the menu options allowed according to the user's alarms,fire alarms, and supervision devices.
authority level. Passcode-controlled menus provide users Commercial Wireless
only with the options and information pertinent to them, The Commercial Wireless platform, powered by Inovonics
simplifying system operation.
wireless mesh network technology,ensures superior range,
Passcode Follows Scope reliability, and scalability for commercial applications.
Use Passcode Follows Scope to restrict passcode arming Using a wide range of transmitters and repeaters, this
and disarming to the keypad's immediate local area,even if proven technology provides flexibility and performance to
the keypad can report events from other areas. Passcode meet the most stringent requirements.This exclusive
Follows Scope simplifies the arming and disarming protocol is available only on Commercial Wireless products.
procedure without limiting any other keypad capabilities.
Invisible Walk Test
A menu item allows the user to test invisible 24-hour points
within the scope of the keypad without sending a report to
the central station.
� •�•
�•� . . �
The Commercial Wireless platform sends redundant When resetting alarms or arming or disarming a system,the
information on several multi-frequency channels within the user is identified by name and number.
FCC Part 15 900 MHz band, providing superior range and ROM Updates
reliability. In comparison, systems that use a single An on-site flash update key provides for easy feature
frequency technology can only send information on one enhancements without replacing ROM chips.
narrow band channel.Any interference within the band can
cause missed signals. With wireless registration, it is easy
to add this technology to any application. Certifications and Approvals
Event Log
The event log stores up to 1,000 local and transmitted The D9412GV3 has been designed to comply with the
events.The event log includes time,date,event,area,point, following:
and user number. View the event log from a keypad or use USA UL AMCX:Central Station Alarm Units
RPS to remotely retrieve event information. RPS operators (UL1610,UL1635),
can retrieve events periodical ly using one phone call,rather AMTB:Control Panels,SIA False Alarm
than receiving several calls each day.When the event log Reduction(ANSI/SIACP-01-2000),
reaches a programmed threshold of stored events, it can AOTX:Local Alarm Units(UL464,UL609),
send an optional report to a receiver. APAW:Police Station Alarm Units
(UL365,UL464),
Access Control APOU:ProprietaryAlarm Units(UL1076),
The D9412GV3 provides custom door strike, point shunt NBSX:Household BurglarAlarm System Units
and auto disarming response by area.There are 14 (UL1023),
UOJZ:Control Units,System
panel-wide access levels with both manual and scheduled (UL864,9thedition),
control. UTOU:Control Units and Accessories-
Store,view, or print access events such as: Household System Type(UL985)
• Access granted
fCC
• No entry
• Request-to-enter
• Request-to-exit Installation/Configuration Notes
Scheduled Events(Skeds) Compatible Products
The internal clock and calendar start individually scheduled
events (skeds). Skeds perform functions such as arm or Keypads D1260SeriesKeypads
disarm, relay control, or point bypassing.The D9412GV3 (D1260,D1260W,D1260R,D1260BLK,
Control Panel offers:
D1260B)
D720 Series Keypads
• 40 scheduled events with up to 25 different functions (D720,D720W,D720R,D720B)
• Eight opening windows and eight closing windows D1255SeriesKeypads
• Eight user windows
• Day-of-week, date-of-month, or holiday only schedules (D1255,D1255W,D1255B,D1255RB)
• Four holiday schedules of 366 days each (leap year) D1256RBFireKeypads
Fire Test D1257RB Remote Fire Alarm
When a user activates Fire Test Mode, the control panel Annunciators
suppresses all reports to the central station.The keypad D279AIndependentZoneControl
and annunciator show all testing data.An automatic sensor Detectors D278S four-wireAddressable DetectorBase,
reset feature saves time;you do not need to reset the 12 VDC
sensors manually.At the end of test,the keypad shows the D285/THPhotoelectricSmokeDetectorHeads
number of untested points. D298SAddressableDetectorBase,24VDC
Programming, Diagnostics and Controls D7050 Series Addressable Photoelectric Smoke
Installers can program on-site with a D5200 Programmer, andSmokeHeatDetectorHeads
Direct-connect, or remotely through RPS.A programmable F220-B6PM/SAddressableDetectorBaseswith
system passcode prevents unauthorized remote POPITs
programming. MX775i Addressable PIR Detector
D9412GV3 Control Panels accommodate up to four MX794iLongRangeMultiplexPlRDetector
separate destinations for primary, alternate, and backup MX934iAddressablePlRDetector
receivers for automatic test reports. MX938i Addressable PIR Detector
ZX776Z PIR Detector
www.boschsecurity.com
.�• ,
� �•� . . -
ZX794Z Long Range PIR Detector Readers ARD-R10 iCLASS Mullion Reader
ZX835 TriTech Microwave/PIR Detector ARD-R40 iCLASS Switchplate Reader
ZX935Z PIR Detector ARD-RK40-09 iCLASS PIN Reader
ZX938Z PIR Detector ARD-VSMART iCLASS Reader
ZX970 PIR/Microwave Detector D8223 Prox Pro Reader
Bosch conventional detectors,including Blue Line, D8224 Mullion Reader
seismic,PIR,TriTech PIR M icrowave,photoelectric, D8224-SP Switch Plate Reader
heat,and smoke.
D8225 Mini Mullion Reader
Enclosures D8103 Universal Enclosure D8301W Low-profile Proximity Readers
D8108A Attack-resistant Enclosure
D8109 Fire Enclosure Commercial Wireless ISW-D8125CW Commercial Wireless Interface
Products ISW-EN7280 Serial Receiver
Magnetic Contacts Bosch magnetic contacts include recessed, ISW-EN4200 Serial Receiver
terminal connection,miniature,overhead door, ISW-EN4204R LED Receiver
and surface mount.
ISW-EN4216R LCD Receiver
Modules Conettix ITS-DX4020-G GPRS/GSM Integrated ISW-EN4016SK Survey Receiver
Communicator
ISW-EN5040-T High-power Repeater
Conettix DX4020 Network Interface Module
ISW-EN1210 Universal Transmitter(Single-input)
Conettix DX4010V2 USB/Serial Interface Module ISW-EN1210EOL Universal Transmitter with EOL
Conettix C900V2 Dialer Capture Module Resistor
D113 Battery Lead Supervision Module ISW-EN1210SK Survey Transmitter
D125B Dual Class B Initiating Module ISW-EN1210W Door-Window Transmitter with
D127 Reversing Relay Module Reed Switch
D129 Class A Initiating Module ISW-EN1215EOL Universal Transmitter with Wall
D130 Auxiliary Relay Module Tamper and EOL Resistor
D185 Reverse Polarity Signaling Module ISW-EN1215WEOL Door-WindowTransmitterwith
Wall Tamper,Reed Switch,and EOL Resistor
D192G Notification Appliance Circuit Module ISW-EN1223D Water-resistant Pendant
D928 Phone Line Switcher Transmitter(Double-button)
D5060 MUX Programmer ISW-EN1223S Water-resistant Pendant
D8125 POPEX Point Expander Transmitter(Single-button)
D8128D OctoPOPIT Eight-point Expander ISW-EN1223SK Survey Pendant Transmitter
D8125MUX Point Expander ISW-EN1233D Necklace Pendant Transmitter
D81251NV Wireless Interface Module
(Double-button)
D8129 Octo-relay Module ISW-EN1233S Necklace Pendant Transmitter
(Single-button)
D8130 Door Release Module ISW-EN1235D Beltclip Pendant Transmitter
D9127 Series POPIT Modules (Double-button)
D9131A Parallel Printer Interface Module ISW-EN1235S Beltclip Pendant Transmitter
D9210BLC Access Control Interface Module (Single-button)
DS7432 Eight-input Remote Module ISW-EN1235DF Fixed-location Transmitter
DS7457i Series Single-zone Multiplex Input (Double-button)
Modules ISW-EN1235SF Fixed-location Transmitter
DS7460i Two-input Module (Double-button)
DS7461i Single-input Multiplex Module ISW-EN1242 Smoke Detector-Transmitter
DS7465i Input and Output Module ISW-EN1247 Glass-break SensorTransmitter
ICP-SDI-9114 SDI Splitter ISW-EN1249 Billtrap Transmitter
ISW-EN1260 PIR Motion Sensor Transmitter
Programming D5200 Series Programmers (Commercialand High-end DomesticApplications)
RPS or RPS-LITE Remote Programming Software ISW-EN1261HT PIR Motion Sensor Transmitter
(High-traffic Areas)
,«,
�•� . . -
ISW-EN1262 PIR Motion Sensor Transmitter Parallel Printers: 3
(Residential and Low-traffic Commercial Points: 246(8 on-board,up to 238 off-board)
Applications)
ISW-EN1265 PIR Motion Sensor Transmitter Programmable Relay Outputs: 131
(Ceiling-mount Applications) RF Points: 238
SKEDs: 64
Power Requirements
Parts Included
Current Draw(Maximum): 300 mA
The D9412GV3 includes the following parts:
Output(Alarm): 2 A at 12 VDC
Quant. Component Output(Auxiliary,Continuous 1.4 A at 12 VDC nominal
1 D9412GV3 Board Power,and Switched Auxiliary
combined):
1 Mounting Skirt
1 Faceplate with D9412GV3 Label Voltage(Operating): 12 VDC nominal
Voltage(AC): 16.5 VAC 40 VA plug-in transformer
The available kits come with the parts indicated in the following table: (D1640)
K�u Trademarks
Components -A -B -C Trademark names are used throughout this document. In
D9412GV3 Board 1 1 1 most cases, these designations are claimed as trademarks
D101FLockandKeySet 1 or registered trademarks in one or more countries by their
D122 Dual Battery Harness 1 respective owners. Rather than placing a trademark symbol
D161 Dual Modular Phone Cord 2 in every occurrence of a trademark name, Bosch Security
D928 Dual Phone Line Switcher 1 Systems, Inc. uses the names only in an editorial fashion
and to the benefit of the trademark owner with no intention
D1640Transformer 1 1 of infringing the trademark.
D8103 Enclosure 1
D8108A Attack-resistant Enclosure 1 Inovonics is a trademark of Inovonics Wireless Corporation.
D8109 Fire Enclosure 1
Ordering Information
Technical Specifications D9412GV3 D9412GV3
Includes one printed circuit board(PCB).
Communications
D9412GV3-A D9412GV3-A
SDI Bus A(+): 9 VDC Contains one PCB,one transformer,and one
4572 m(15,000 ft) attack-resistant enclosure.
SDI Bus B(-): 9 VDC D9412GV3-B D9412GV3-B
4572 m(15,000 ft) Contains one PCB,one dual battery harness,
Telephone • One telephone line two telephone cords,one telephone line
Connection: • D928 Dual Phone Line Module required for two switcher,one transformer,and one fire enclo-
telephone lines sure.
D9412GV3-C D9412GV3-C
Environmental Considerations Contains one PCB,one lock and key set,one
Relative Humidity: 5%to 93%at+30°C(+86°F), transformer,and one universal enclosure.
non-condensing
Temperature(Operating): 0°C to+50°C(+32°F to+122°F)
Number of...
Areas: 8
Card Readers(Doors): 8
Credentials(Tokens): 996
Custom Functions: 16
Events: Up to 1000
Passcode Users: 249,plus 1 service passcode
www.boschsecurity.com
�.
�•� . . •
Ordering Information Ordering Information
Accessories D1640 Transformer D1640
ICP-SDI-9114 SDI Splitter ICP-SDI-9114 System transformer rated at 16.5 VAC,40 VA.
Provides the ability to set up two independent D8004 Transformer Enclosure D8004
SDI buses from a single SDI connection on the For applications such as fire alarm that might
control panel. require a transformer enclosure.
D928 Dual Phone Line Switcher D928 D8103 Enclosure D8103
Allows the control panel to operate over and Grey steel enclosure measuring 41 cm x 41 cm
supervise two separate phone lines.Only one x 9 cm(16 in.x 16 in.x 3.5 in.).
D 162 phone cord is supplied.Two additional D8108A Attack Resistant Enclosure D8108A
D161 or D162 phone cords are required.
Grey steel enclosure measuring 41 cm x 41 cm
DS10 Tamper Switch D110 x 9 cm(16 in.x 16 in.x 3.5 in.).UL Listed.
Screw-on tamper switch that fits all Includes lock and key set.Requires the D2402
enclosures.Shipped in packages of two. Mounting Plate.
ICP-EZTS Dual Tamper Switch ICP•EZTS D8109 Fire Enclosure D8109
Combinationtamperswitchwithawireloopfor Red steel enclosure measuring40.6cm x
additional tamperoutputs. 40.6 cm x 8.9 cm(16 in.x 16 in.x 3.5 in).
D101 Lock and Key Set D101 UL Listed.Includes a lock and key set.
Standard lock set with one key supplied.Uses D9002-5 Mounting Skirt D9002-5
the D102(#1358)replacement key. Mounts inside D8103,D8108A,and D8109
D322 Dual Battery Harness D122 enclosures.Can accept up to six standard
Harness with circuit breaker.Connects two 7.62 cm x 12.7 cm(3 in.x 5 in.)cards.
batteries to a compatible control panel. Software Options
D122L Dual Battery Harness with Long D122L RPS Kit(LPT) D5500C•LPT
Leads Account management and control panel-
Color-coded harness with circuit breaker and programming software with LPT connection.
leads measuring89cm(35 in.).Connects 12 V RPS Kit(USB) D5500C•USB
batteries to compatible control panels. Account management and control panel-
D126 Standby Battery(12 V,7 Ah) D126 programming software with USB connection.
Sealed lead-acid standby and auxiliary
rechargeable power supply.
D1218 Battery(12 V,18 Ah) Di218
A 12 Vsealed lead-acid batteryforstandbyand
auxiliary power with two bolt-fastened
terminals.Includes hardware for attaching
battery leads or spade connectors
D1224 Battery(12 V,26-28 Ah) D1224
A 12 Vsealed lead-acid batteryforstandby and
auxiliary power with two bolt-fastened
terminals.Includes hardware for attaching
battery leads or spade connectors.
D3238 Battery(12 V,38 Ah) D1238
A 12 V sealed lead-acid battery for stand by and
auxiliary power with two bolt-fastened
terminals.Includes hardware for attaching
battery leads or spade connectors.
D137 Mounting Bracket D137
Used to mount accessory modules in D8103,
D8108A,and D8109 enclosures.
D138 Mounting Bracket,Right Angle D138
Used to mount accessory modules in D8103,
D8108A,and D8109 enclosures.
Americas: Europe,Middla Eas4 Afrlca: AslrPaclflc: Representad by
Bosch Security Systems,Inc. Bosch Security Systems B.V. qobert Bosch(SEA)Pte Ltd,Security Systems
130 Perinton Parkway P.O.Box 80002 11 Bishan Street 21
Fairport,New York,14650,USA 5600 J0 Eindhoven,The Netherlands Singapore 573943
Phone:�l 800 289 0096 Phone:*31 40 2577 284 Phone:.65 6571 2600
Fax:+1 SBS 223 9180 Fax:r31 40 2577 330 Fax:.65 6571 2698
security.sales�us.bosch.com emea.securitysystemspbosch.com apr.securitysystems@bosch.com
www.boschseturity.us www.boschsecuri[y.com www.boschsecurity.com
�Bosch Security Systems Inc.20101 Da[a subject to thange without notice
T6695631627 I Cur.en-US,Vl,27 Apr 2030
� • •.•
� BOSCH
�
Invented for life
D1256 Fire Keypad
► Provides system control with easy to use function keys
► Built-in multi-tone sounder
► Easy to read vacuum fluorescent display shows
����t ���« complete system status in English format
�
--. - - � - . - -� � ��E�,.a« qESET ► Programmable custom text for each point
�'�.iNCY�TOqp[QEt,-- . �ocal system test display
` ""'� '�"' '"� ► Molded red ABS piastic construction
� � �
The D1256 Fire Keypad is a full-function system controller Certifications and Approvals
and annunciator. Four one-touch function keys provide
user-friendly control over the system. The function keys Region Certification
allow the user to silence the audible alarm output, silence
the trouble sounder, reset the annunciator display, and USA UL AMCX:Central Station Alarm Units
reset the system detectors. Four additional navigational (UL1610,UL1635),AMTB:Control
Panels,SIA False Alarm Reduction,APAW:
keys allow access to other programmed system functions. PoliceStationAlarmUnits(UL365,
The D1256 can be mounted in secure areas. UL464),APOU:ProprietaryAlarmUnits
(UL1076),NBSX:Household Burglar
Alarm System Units(UL1023),UOXX:
Control UnitAccessories,System(UL864,
9th edition),UTOU:Control Units and
Accessories-Household System Type
(UL985)
FM
CSFM 7167-1615:100,7165-1615:113,
7165-1615:119,7170-1615:144,and
7170-1615:145 July 2008
NYC-MEA 12-92-E,Vol.12 12-92-E,Vol.12
12-92-E,Vol.15 12-92-E,Vol.15
www.boschsecurity.com
� . ..
Installation/Configu�ation Notes Ordering Information
Compatible Control Panels D1256 Fire Keypad D3256
The D1256 Fire Keypad is compatible with the D9412GV2, Full-functionsystemcontrollerandannuncia-
D7412GV2, D7212GV2, D7212, D7212B1, D7212G, D7412, tor
D7412G, D9112, D9112B1, D9124 (using the D9112LTB, Accessories
the D9112LT6-EX,orthe D9412GLTB),D9412,and D9412G D54BBrassFlush-mountKit D54B
Control Panels. Back box and polished brass faceplate.
Mounting D54C Stainless Steel Flush•mount Kit D54C
The D1256 is a low profile,surface-mounted unit molded in Backboxandstainlesssteelfaceplate.
durable red plastic with three mounting holes in the base D55KeypadDeskStand D55
that allow secure, correct positioning during installation. Portabledeskstand insmokecolored Plexi-
Protect the surface-mounted D1256 by mounting it to a D56 glas.
or D56R Conduit Back Box. The D1256 can be flush D56SurfaceMountConduitBox D56
mounted using a D546 or D54C Flush-mount Kit. For Whitesurfacemountbox.
desktop applications, the D1256 can be mounted to a D55 D56RRedSurfaceMountConduitBox D56R
Desk Stand. Red surface mount box.
Note Do not install the D1256 in direct sunlight.This
damages the module components and makes
the display less visible. Do not mount the
D1256 in wet or moist locations.
Wiring
The D1256 connects to the FACP through a standard four-
wire cable.The field wiring connects to a four-wire harness
supplied with the unit. This harness plugs into a four-pin
connector on the circuit board through the back of the
D1256.
Note Use shielded cable where excessive
electromagnetic interference is a problem.
Technical Specifications
Environmental Considerations
Relative Humidity: 5%to 85%non-condensing at+86°F
(+30°C)
Temperature(operating): +32°F to+122°F(0°C to+50°C)
Mechanical Properties
Color: Red
Dimensions(H x W x D): 8.3 in.x 4.5 in.x 0.8 in.
(21cmx11.4cmx2cm)
Material: Molded ABS plastic
Power Requirements
Current: 104 mA minimum,206 mA maximum
Voltage: 12 VDC nominal supplied by the control pan-
el
�����+� Europs,Middla East,Africa: AsfrPaclfic: papresentad by
Bosth Security Systems,Inc. Bosch Security Systems B.V. Robert Bosch(SEA)P[e Ltd,Seturity Systems
130 Perinton Parkway P.O.Box 80002 11 Bishan Street 21
Fairport,New York,14450,USA 5600 JB Eindhoven,The Netherlands Singapore 573943
Phone:rl 800 269 0096 Phone:+31 40 2577 284 Phone:r65 6258 5511
Fax:«1 585 223 9180 Faz:+31 40 2577 330 Fax:r65 6319 3499
securitysales@us.bosch.com emeasecuritysystems�bosch.com aprsecuritysystems@bosch.com
www.boschsecurity.us www.bosthsecurity.com www.boschsecurity.com
�Bosch Sewrity Systems Inc 20091 Data subjea to change without notice
T1295038475 I Cur:en-U5,V3,27 Oct 2009
• ' � • � � �
�� BOSCH
�
Invented for life
ICP-SDI-9114 SDI Splitter
� ��� � � ► Provides two independent, isolated SDI buses from a
° FG r--n— � �: ��`\� �,�- � -- single SDI connection to the control panel
�_
�;•<- -.- � ► �" .� i a..L -�-�' uL:.' ► Can be used to meet the requirements for a UL864
��0�`!�� � - p p ti��:`;"�ig 0 0 0 compliant combination control panel
'�`�� � ���. � ��m!:.�'��� ��- , ► Does not affect the operation of the control panel or
��� ��,; � n m � ,,�,� :,,- the associated SDI devices
_������'-�.i � -J , . Additional power can be supplied by an external power
� suPP�Y
��� �� .n ?, .�
Z���!�_ __ . - ,,� �,
The ICP-SDI-9114 SDI Splitter allows the set up of two Functions
independent, isolated SDI buses from a single SDI Connections
connection on the control panel. When this accessory is
installed with a control panel and wired to create separate The SDI splitter has three sets of four-position SDI
SDI buses for fire and intrusion devices,the system is a terminals: PANEL, FIRE,and BURG. The PANEL terminals
UL864 compliant combination control panel. are used for the SDI connection to the control panel.The
terminals labeled FIRE and BURG are handled equally,and
Note The D9412GV2 and D7412GV2 control panels either terminal can be assigned to any collection of devices
can be installed as a combination system per that require two separate buses.The SDI splitter does not
UL864, 9th edition requirements when used affect the operation of the control panel or the associated
with the ICP-SDI-9114 SDI Splitter. SDI devices.
The ICP-SDI-9114 SDI Splitter is compatible with Bosch LEDs
Security Systems,Inc.'s D9412GV2,D7412GV2,D7212GV2, The SDI splitter has three green LEDs (labeled PANEL
D9412G, D7412G, D7212G, and D9124 control panels. ACTIVE, FIRE ACTIVE, and BURG ACTIVE) that monitor bus
activity.
Note The D7212GV2 and D7212G are not rated for
Commercial Fire. Power
The SDI splitter operates on power from the control panel,
but the DC current is limited to 550 mA for each bus (FIRE
and BURG),or enough power for two D1255 or two D1260
keypads.An external power supply, connected with a
common ground, is required to provide power for devices
that exceed the 550 mA limit.
A total of up to 32 SDI devices can connect to the output
buses.A fault to the power or data connections of one bus
does not affect the other bus.
www.boschsecurity.com
' � • � � •
Certifications and Approvals Outputs
Current(BURG bus): 550 mA maximum from control panel
Region Certification Current(FIRE bus): 550 mA maximum from control panel
USA UL UOXX:Control UnitAccessories,System powerRequirements
(UL864,9th edition)
CSFM 7165-1615:119 Control Unit Current: 30 mA maximum
(Non High-Rise) Voltage(supply): 12.0 VDC nominal
Installation/Configuration Notes Ordering Information
Mounting Considerations ICP-SDI-9114SDISplitter ICP•SDI-9114
Note ULrequiresthattheSDlsplitterbemountedin Providestheabilitytosetuptwoindependent
SDI buses from a single SDI connection on the
the same enclosure with the control panel, or control panel.
in a separate enclosure in the same room
within 20 ft (6.0 m) of the control panel and
connected by conduit.
Wiring Considerations
Wiring from the control panel to SDI splitter should be
0.8 mm(22 AWG)to 2.0 mm(12 AWG)wire with a maximum
wire length of 6.0 m(20 ft).The maximum impedance of the
wire from the control panel to the SDI splitter must not
exceed 1 f2.
The maximum total wiring length for any single bus is
3048 m (10,000 ft).To determine the maximum impedance,
maximum wire length and appropriate wire gauge for wiring
from the SDI splitter to the SDI devices, refer to the
specifications for each SDI device.
Parts Included
�uant. Component
1 SDI splitter
1 Hardware pack
1 Literature pack
Technical Specifications
Environmental Considerations
Relative Humidity: 93%maximum,non-condensing
Temperature(operating): 0°C to+50°C(+32°F to+122°F)
Mechanical Properties
Dimensions(H x W x D): 127 mm x 74 mm x 25.4 mm
(5 in.x 2.9 in.x 1 in.)
Weight: 0.13 kg(4.6 oz)
Amarlcas: Europa,Middla East,Africs: AsirPacfflc: Represe�tW by
Bosch Security Systems,Inc. Bosth Security Systems B.V. Robert Bosch(SEA)P[e Ltd,Securi[y Systems
130 Perinton Parkway P.O.Box 80002 11 Bishan Street 21
Fairport,New York,14450,USA 5600 JB Eindhoven.The Netherlands Singapore 573943
Phone:+1 800 289 0096 Phone:r 31 40 2577 284 Phone:+65 6571 2600
Fax:*1 585 223 9180 Fax:+31 40 2577 330 Fax:+65 6571 2698
security.sales@us.bosch.com emea.securitysystems�bosch.com apr.securitysystems@bosch.com
www.boschsecurity.us www.boschsecurity.com www.boschseturity.com
�Bosch Security Systems Inc.20101 Data subject to change without notice
T41802411631 Cur:en-US,V7,7 Jan 2030
. �: :� • .-�- . .-
' ���) B�SCH
�
Invented for life
D8128D OctoPOPIT Eight-point Expander
--
► Provides point identification for initiating devices
_ =�—--_ ;T�„ F4� :" ►
;Yna�280 4���-. , r- � Expands the number of points in the system
r� '��� ��� �°� ��� ��� ` ► DIP switch programmable
,
� " �,���� �� � �
�^ '� 11�'�-� �� ce,te� .r,ia
� � ��
���� ��,��� �.' �_r—..w N
,��` �� �e ('f21
' �Y -� `�► , i = �` 8� � .�- ��'
C � � .� a ). t� '�
ay►�� �SeiW�i •�U/����11f�1l�
The D8128D OctoPOPIT module combines the functions of Certifications and Approvals
the D8125 POPEX module and the D8127 and D9127U and
D9127T POPIT modules to provide eight Class B (Style B) Region Certification
off-board points in a single module.The D8128D OctoPOPIT
and D8125 POPEX modules can be wired in parallel to the USA UL AMCX:CentralStationAlarmUnits
ZONEX Bus terminals on the same panel. (UL1610,UL1635).AOTX:Local Alarm
Units(UL464,UL609),AOTX7:Local
Alarm Units Certified for Canada(cULus),
APOU:Proprietary Alarm Units(UL1076),
System Overview NBSX:Household Burglar Alarm System
Units(UL1023),NBSX7:Household
The module can be installed inside the enclosure of the BurglarAlarm System UnitsCertifiedfor
control panel, or the module can be installed in a separate Canada(cULus),UOXX:Control Unit
enclosure and connected to the control panel. Accessories,System(UL864,9thedition),
UTOU:Control Units and Accessories-
Household System Type(UL985),UTOU7:
Functions Control Units and Accessories-Household
System Type Certified for Canada(cULus)
Address Switches
CSFM 7167-1615:100,7165-1615:133,
There is a set of DIP switches for setting point assignments 7165-1615:119
and line termination. Switches 1 to 4 assign the sensor
loops to point numbers on a compatible control panel. NYC-MEA 12-92-E,VoI.12 12-92-E,VoI.12
Switch 5 sets the line termination. 12-92-E,VoI.15 12-92-E,VoI.15
Point DIP Switches Australia C-Tick
Activate or deactivate each point connected to the module
by placing its respective DIP switch in the closed or open
position.The point DIP switch can be used to deactivate
conflicting points.
www.boschsecurity.com
�S S� • •'�' •• •. •-
Installation/Configuration Notes Loop
Compatibility Information Wire Resistance: 100 f�maximum
Control Panels D9412GV2 Response Time: 1 second(supervised with a 1 kfl end-of-line resis-
tor)
D7412GV2
D7212GV2" Power Requirements
D9412G Current(alarm): 50 mA maximum
D7412G Current(standby): 25 mA maximum
D7212G' Voltage: 12 VDC nominal
D9412 Trademarks
D7412 Trademark names are used throughout this document. In
D7212' most cases, these designations are claimed as trademarks
*The D7212GV2, D7212G, and D7212 are not listed for or registered trademarks in one or more countries by their
commercial fire applications. respective owners. Rather than placing a trademark symbol
in every occurrence of a trademark name, Bosch Security
Connection Considerations Systems, Inc. uses the names only in an editorial fashion
If the module is installed in a separate enclosure, it can be and to the benefit of the trademark owner with no intention
placed up to 60 m (200 ft) from the control panel: of infringing the trademark.
Maximum Wire Impedance:4 n Molex is a registered trademark of Molex Incorporated
Distance(maximum) WireSize
60 m 0.6 mm
60 m 1.0 mm Ordering Information
200 ft 22 AWG D8128D OctoPOPIT Eight-point Expander D8128D
200 ft 18 AWG Provides 8 off-board points and a set of DIP
switches.
The module can be wired to the control panel using the Accessories
module's terminal strip or using Molex connectors.The
Molex connectors are useful when multiple D8128D D337MountingBracket D137
Used to mount accessory modules in D8103,
modules are in use.The terminal strip is easier to use in D8108A,and D8109 enclosures.
cases when the module is connected directly to the control D203 Enclosure D203
panel.
D8303 Enclosure D8103
D8108A Attack Resistant Enclosure D8108A
Parts Included Greysteelenclosuremeasuring41cmx41cm
x 9 cm(16 in.x 16 in.x 3.5 in.).UL Listed.
Quantity Component Includeslockandkeyset.RequirestheD2402
Mounting Plate.
1 OctoPOPIT
D8309 Fire Enclosure D8309
1 Hardware pack Red steel enclosure measuring 40.6 cm x
1 Literature pack 40.6 cm x 8.9 cm(16 in.x 16 in.x 3.5 in).UL
Listed.Includes a lock and key set.
Technical Specifications
Environmental Considerations
Temperature(Operating): 0°C to+49°C(+32°F to+120°F)
Amarlcas: Europa,Mlddla East,Africa: AsirPacif(c: RapresentW by
Bosth Security Sys[ems,Inc. Bosch Security Systems B.V. Robert Bosch(SEA)Pte Ltd,Security Systems
130 Perinton Parkway P.O.Box 80002 Il Bishan Street 21
Fairport,New Vork,14450,USA 5600 JB Eindhoven,The Netherlands Singapore 573943
Phone:rl 800 2B9 0096 Phone:+31 40 2577 286 Phone:+65 6571 2600
Fax:.1 585 223 9180 Fax:.31 40 2577 330 Fax:�65 6571 2698
security.sales�qus.bosch.com emea.securitysystems(�bosch.com apr.securitysystems�bosch.com
www.boschsecurity.us www.boschsewrity.com www.boschsecuriry.com
m Bosch Security Systems Inc.2009 I Data subject to change without notice
T1159086475 I Cur:en-US,V9,3 Dec 2009
• �S •
��' BOSCH
�
Invented for life
D8125MUX Multiplex Bus Interface
J - ` ► Multiplex bus controls two independent buses
OC �
ov�, _ ;U� ��,., ��� ,. :+ ► Aux Power terminals that can be used for remote
�,;� , -� '�" , k _ , devices
,�><<�_ - = � _
� ��'� �r/ �""''�.� �";_ 5' � ► Programmed with D5060 Handheld Programmer(not
�f
� . � - required for"i"class modules)
a
m ��`���.` ��'"� ���'� �+� � � �` ► Operation monitoring LED
, , �, ��.� � � �;�.. �,�,� .
�: ' '} �,,4�,�, 1 � i ► Connect to Zonex i or Zonex 2
� r �y,�l ` ; t' � ��"� ► Standard three hole mounting
�
� { ► Accepts Daisy Chain and T•Tapping bus configurations
��
�� r��� . ° �
The D8125MUX Multiplex Bus Interface Module and D5060 Hand-held Programmer
associated modules are used to expand the compatible Use the D5060 Multiplex Point Programmer to program
Bosch control panels beyond their standard number of multiplex bus points.The D5060 is not required when
onboard initiating zones or points.The D8125MUX module programming"i"class modules. In addition to programming
is installed in the control panel enclosure,and is connected points, use the D5060 to view the MUX device point
to either Zonex 1 or Zonex 2 on the control panel where it number.
scans the multiplex (MUX) points connected to it and
reports the points' status to the control panel. Point index
programming then determines if an action on the part of the Certifications and Approvals
control panel is required (alarm response,trouble
response, and so on). Region Certification
USA UL AMCX:Central Station Alarm Units
Functions (UL1610,UL1635),AOTX:Local Alarm
Units(UL464,UL609),APAW:Police
Two Independent Buses Station Alarm Units(UL365,UL464),
The multiplex bus interface can control two independent APOU:ProprietaryAlarm Units(UL1076),
buses.A fault on one MUX bus does not prevent the other NBSX:Household BurglarAlarm System
from operating normally. Units(UL1023),UTOU:Control Units and
Accessories-Household System Type
Aux Power Terminals
(UL985) Refer to D8125MUX Operation
The D8125MUX has Aux Power terminals labeled PowerA andlnstallationGuide(P/N:36796)forUL
(+,-) and Power B (+,-)that can be used for remote devices UOJZ:Control Units,System(UL864,9th
that require an uninterrupted source of power. Up to edition)
200 mA are available at these terminals. CSFM 7167-1615:100,7165-1615:113,
Note Observe correct polarity when connecting
7165-1615:119
devices to these power terminals.
www.boschsecurity.com
�: . :
Installation/Configuration Notes Technical Specifications
Compatibility Information EnvironmentalConsiderations
Control Panels D9412GV2 Control Panel Relative Humidity: Up to 93%,non-condensing
D9412G Control Panel Temperature(Operating): 0°C to+49°C(+32°F to+120°F)
D7412GV2 Control Panel Properties
D7412G Control Panel
D7212GV2 Control Panel Board Dimensions: 14 cm x 8.3 cm x 2.5 cm
D7212G Control Panel (5.5 in.x 3.25 in.x 1.0 in.)
D9124 Fire Alarm Control Panel Power Requirements
Multiplex Modules DS7432 Series Eight-input Remote Modules Current: 128 mA maximum
DS7457i Series Single-zone Input Modules Voltage: 12 VDC
DS7460i Dual-zone Input Module
DS7461i Single-zone Input Module
DS7465ilnput-outputModule Ordering Information
Programmers D5060 Multiplex Programmer D8125MUX Multiplex Bus Interface D8125MUX
Wiring Controls two independent buses.
Maximum Wire Impedance:33 fl
Distance(approximate) Size
610 m 0.8 mm
1524 m 1.2 mm
2000 ft 22 AWG
5000 ft 18 AWG
Control Panel to D8125MUX Module Wiring
The recommended wiring from the control panel to the module
is quad(four-wire) cable. Do not use shielded or twisted-pair
cable. If used in fire applications, 18 AWG wire is required.
Maximum Impedance:4.05 fl at+20°C(+68°F)nominal
Distance(approximate) Size
76 m 0.65 mm
193 m 1.02 mm
250 ft 22 AWG
600 ft 18 AWG
Data Loop Wiring
Use non-shielded wire for data loops.Do not exceed 75 mA on
each MUX Bus output.
Parts Included
�uantity Component
1 Multiplex Bus interface
1 Hardware pack
1 Literature pack
Ameritas: Europe,Middl�East,Africa: AalrPacific: Reprasented by
Bos[h Security Systems,Inc. Bosch Security Sys[ems B.V. Robert Bosch(SEA)Pte Ltd,Securi[y Systems
130 Perin[on Parkway P.O.Boz 80002 11 Bishan Street 21
Fairport,New Vork,14450,USA 5600 JB Eindhoven,The Netherlands Singapore 573943
Phone:�1 800 289 0096 Phone:+31 40 2577 284 Phone:.65 6571 2600
Fax:+1 585 223 9180 Fax:*31 40 2577 330 Fax:*65 6571 2698
seturity.sales(�us.bosch.com emea.securitysystems(�ybosch.com apr.securitysystems@bosch.com
www.boschsecurity.us www.boschsecurity.com www.boschsecurity.com
m Bosch Security Systems Inc.20091 Data subject to change without notice
T1158945931 I Cur:en-US,V8,3 Det 2009
. � � • • ••
��-� BOSCH
�
Invented for life
DS7457i Series Single-zone Input Modules
► Power-limited and supervised input zones
� ► Compact enough to fit within most back boxes and
enclosures
► Address settings through DIP switches
The DS7457i Series Single-zone Input Modules includes the Region Certification
DS7457i and the DS7457iF. Each model has a supervised USA UL Bothmodels:AMCX:CentralStationAlarm
input zone for connecting normally-open (NO) or normally- Units(UL1610,UL1635),AOTX:Local
closed (NC) contacts.The DS7457i Series supervises the Alarm Units(UL464,UL609),APAW:
contacts using47 kfl end-of-line(EOL) resistors. Each PoliceStationAlarmUnits(UL365,
model operates with compatible multiplex expansion UL464)
modules and occupies one multiplex zone address on the DS7457iFonly:NBSX:Household Burglar
system. The DS7457i is designed for intrusion applications Alarm System Units(UL1023),UOXX:
while the DS7457iF is designed for fire applications. ControlUnitAccessories,System(UL864,
9th edition),UTOU:Control Units and
Accessories-Household System Type
Certifications and Approvals (UL985)
CSFM DS7457iF:7165-1615:113,
7165-1615:199
Region Certification
Europe CE DS7457iF:89/336/EEC,EN55022:
1998.EN50130-4:1995,EN60950:
2000,EN61000-3-2,EN61000-3-3,
EN61000-4-2,EN61000-4-3,
EN61000-4-4,EN61000-4-5,
EN61000-4-6,EN61000-4-11
Belgium INCERT B-509-0005 (DS7457i only)
www.boschsecurity.com
� � • • ••
Installation/Configuration Notes PowerRequirements
Compatibility Information Current Draw: 0.5 mA maximum
Control Panels D9412GV2,D7412GV2,and D7212GV2 Con• Voltage(Operating): 8 VDC peak(minimum)
trol Panel
D9412G,D7412G,and D7212G Control Panels
D9412,D7412,and D7212 Control Panels Ordering Information
DS7400Xi Control Panel DS7457i Single-zone Input Module DS7457i
Multiplex Modules D8125MUX Multiplex Bus Interface Connects normally-open(NO)or normal-
DS7430 Multiplex Expansion Module ly-closed(NC)contacts,and supervises the
contacts using 47 kII end-of-line(EOL)resis-
DS7436 Multiplex Expansion Module tors.Designed for intrusion applications.
The DS7457i Series Modules require a multiplex expansion DS7457iFSingle-zonelnputModule DS7457iF
module to connect to the contro/panels. Connects normally-open(NO)or normal-
ly-closed(NC)contacts,and supervises the
Wiring Considerations contacts using 47 kII end-of-line(EOL)resis-
tors.Designed for fire applications.
Maximum Impedance:4.05 fl at+20°C(+68°F)nominal
Distance(approximate) Size
76 m 0.65 mm
193 m 1.02 mm
250 ft 22 AWG
600 ft 18 AWG
Refer to the intended control panel's installation guide for
multiplex wiring requirements.
The recommended wiring to the control panel is quad (four-
wire) cable. Do not use shielded or twisted pair cable.
Note If used in fire applications, 18 AWG wire is
required.
Parts Included
Quantity Component
1 Single-zone input module
1 Literature pack
Technical Specifications
Circuit Parameters
Initiating Circuit Type(DS7457iF): Class B(Style A)
Signaling Line Circuit Type: Class B(Style 4)
Environmental Considerations
Temperature(Operating): 0°C to+49°C(+32°F to+120°F)
Amaricas: Europa,Mlddla East,Afrlca: AsiaPacific: Nepresanted by
Bosth Security Systems,Inc. Bosch Seturity Systems B.V. Robert Bosch(SEA)P[e Ltd,Securi[y Systems
130 Perinton Parkway P.O.Box 80002 11 Bishan Street 21
Fairport,New York,14450,USA 5600 JB Eindhoven,The Netherlands Singapore 573943
Phone:�l 800 289 0096 Phone:*31 40 2577 284 Phone:+65 6571 2600
Fax:tl 585 223 9180 Fax:.31 40 2577 330 Fax:t65 6571 2698
security.sales�us.bosch.com emea.securitysystemspbosch.com apr.securitysystems@bosch.com
www.boschsecurity.us www.boschseturi[y.com www.bos[hsecurity.tom
O Bosch Securi[y Sys[ems Int.2009 I Da[a subject to thange without notice
TI5266487151 Cur:en-US,V9,3 Dec 2009
. � • • ��• � ••
���� BOSCH
�
Invented for life
D192G Notification Appliance Circuit
(NAC) Module
► Supervises 12 or 24 VDC notification appliance circuits
� (NACs)
► Supervised signal silencing switch
��'—"f � �r`� tr ° � ► Notification appliance circuit rated at 3.0 A
_.�.__—� �,
"�,.:"` �, �~
i$ "� ��, , y�?' � ► Multiple module configurations
�'� �,� . �
�� '�r��.. � �; '�" ► Mounts in panel enclosure
.�:.
,� �.',,�,� ' ii�....,,,:
, . .�„ .r ;.
��_ ,�,�
��
- ,
i ' 3
� .___.�� � � �_.- .
The D192G Notification Appliance Circuit (NAC) Module is Mounts in Panel Enclosure
used with the G Series Control Panels and the D9124 Fire The D192G mounts inside the control panel enclosure using
Alarm Control Panel.The D192G Module is used for wiring existing mounting holes or with a D137 or D138 Mounting
connections to remote alarm devices.The wiring is Bracket. Refer to the control panel's installation guide for
supervised for open,short, or grounded circuit faults. more information on mounting.
Functions Certifications and Approvals
Supervises 12 VDC or 24 VDC NACs
The D192G powers the notification devices from either the Region Certification
control panel's power supply or from a UL Listed Auxiliary USA UL AMCX:Central StationAlarm Units
12 VDC or 24 VDC regulated power-limited power supply for (UL1610,UL1635),APAW:Police Station
use with Fire Protective Signaling Units and Commercial Alarm Units(UL365,UL464),APOU:
and Residential Burglar Units. The choice of power supply ProprietaryAlarm Units(UL1076),NBSX:
allows the use of 12 V or 24 V notification devices. Household BurglarAlarm System Units
Supervised Signal Silencing Switch (IL1023),UOJZ:Control Units,System
(UL864,9th edition)
The D192G Module has a toggle switch for silencing the CSFM 7167-1615:100,7165-1615:113,and
notification devices while testing the alarm panel.When 7165-1615:119
this toggle switch is in the Silence(Off)position,the D192G
indicates a supervisory trouble condition to the control NYC-MEA 12-92-E,Vol.12 12-92-E,Vol.12
panel. For use with G Series Control Panels. 12-92-E,Vol.15 12-92-E,Vol.15
Multiple Module Configurations Australia C-tick
Several modules can be connected to the same zone or
point on the control panel or, if individual annunciation of a
notification appliance circuit is desired, D192G modules
can be connected to separate zones or points.
www.boschsecurity.com
� • • • ��• � ••
Installation/Configuration Notes Ordering Information
Compatibility Information D192G Notification Appliance Circuit D192G
(NAC)Module
Control Panels D9412GV2,D7412GV2,D7212GV2,D7212G, Supervises 12 or 24 VDC notification appli-
D7412G,and D9412G Control Panels ance circuits(NACs).
D9124 Fire Alarm Control Panel
Notification Appliances
Notification appliances used with the D192G Module must:
• Be polarized (DC) equipment
• Match the voltage rating of the alarm power supply
• Not exceed the current rating of the alarm power supply
• Not exceed 3.0 A in combined device current for each
D192G Module
Wiring
Use a Class B,Style W,two-wire circuit and wire according
to the instructions supplied with the module.No more than
twelve D192G Modules can be used per system. For UL
applications,a listed (UTRZ) regulated power supply can be
used to power notification devices through the D192G
Module.
To comply with NFPA Standards:
• The control panel and power supply must be supervised
or installed in the same room not more than 6 m (20 ft)
from the D192G
• Wiring between the control panel and the power supply
must be in conduit
• Power supply fault conditions must be supervised by a
UL Listed relay
Parts Included
Quant. Component
1 NAC module
1 Hardware pack
1 Literature pack
Technical Specifications
Contact Ratings
Current: 3.0 A maximum
Voltage: 12 VDC or 24 VDC nominal
Mechanical Properties
Dimensions: 13 cm x 8 cm x 2 cm(5 in.x 3 in.x 0.75 in)
Outputs
Current: 100 mA maximum
Voltage 12 VDC nominal
Amaricax Europa,Mlddl�East,A}rlca: AslrPaclflc: Represantad by
Bosch Security Systems,Inc. Bosch Sxurity Systems B.V. Robert Bosch(SEA)Pte Ltd,Security Systems
130 Perinton Parkway P.O.Box 80002 Il Bishan Street 21
Fairport,New Vork,14450,USA 5600 JB Eindhoven,The Netherlands Singapore 573943
Phone:+1 800 289 0096 Phone:t 31 40 2577 280 Phone:�65 6571 2600
Fax:rl 5B5 223 9180 Fax:.31 00 2577 330 Fax:+65 6571 2698
security.sales�us.bosch.com emea.securitysystems�bosch.com apr.securitysystems�bosch.com
www.bosthseturity.us www.boschsecurity.tom www.bosthsecurity.com
0 Bosch Security Systems Inc.20091 Data subject to change without notice
T11588434031 Cur:en-US,V9,3 Dec 2009
� �
�: • �: .
� BOSCH
�
Invented for life
D8132 and D8132LT Battery Charger
Modules
► Provide additional standby Ah for control panels
► 1200 mA battery recharging circuit
� = ����W�A • Suitable for 12 VDC,up to 27 Ah of batteries
� ► Suitable as a stand-alone 12 VDC, 1 A power supply
(not rated for UL)
e�TiEA�
et[1/CE
�■�
I
:� �.
The D8132 and D8132LT Battery Charger Modules work Battery Supervision
with external batteries to increase standby time and When the D8132 or D8132LT connects to the same AC
provide additional power to the auxiliary output of branch circuit as the control panel, battery supervision is
compatible control panels. available in stand-alone configurations.
Note The D8132 or D8132LT can be used as a
stand-alone power supply or as a battery
charger.However,the D8132 and D8132LT are
UL rated as battery chargers only, not as
stand-alone power supplies.
System Overview
The D8132 and D8321LT use a 16.5 VAC,40 VA plug-in
transformer(D1640)to supply 1200 mA of battery charging
current.A green LED lights to indicate the presence of AC
voltage.The D8132 model includes the transformer
(D1640), while the D8132LT model does not.
Functions
Stand-alone Power Supply
The D8132 and D8132LT can work as stand-alone, 12 VDC
1 A power supplies with the following stipulations:
• No battery supervision or load shed capability
• No UL Listing
• Not recommended for critical loads
www.boschsecurity.com
� �
�: . �: ..
Certifications and Approvals Application Considerations
Two additional 12 V, 7 Ah batteries or up to two 12 V,
Region Certification 13.5 Ah batteries can be installed with the D8132 or
D8132LT.The D8132 or D8132LT are ideal for systems
USA UL AMCX:CentralStationAlarmUnits requiring extended battery standby time, such as UL Bank
(UL1610,UL1635),AMCX7:Central Safe and Vault applications, and systems requiring
Station Alarm Units Certified for Canada
(cULus),AOTX:LocalAlarmUnits(UL464, additional auxiliary current output.The D8132 or D8132LT
UL609),AOTX7:Local Alarm Units can also be installed as a non-UL Listed 12 V, 1 A
Certified for Canada(cULus),APAW: stand-alone power supply.
Police Station Alarm Units(UL365, Wiring Considerations
UL464),APAW7:Police Station Alarm Instal lers can use a four-wire harness to connect one or two
UnitsCertifiedforCanada(cULus),APOU: batteries to the D8132 or D8132LT.
Proprietary Alarm Units(UL1076),NBSX:
Household BurglarAlarm System Units Mounting Considerations
(UL1023),NBSX7:Household Burglar Installers can mount the battery charger module and
AlarmSystemUnitsCertifiedforCanada batteries inside a separate approved Bosch Security
(cULus),UOJZ:Control Units,System Systems, Inc. enclosure such as the D8103, D8108A, or
(UL864,9thedition),UTOU:ControlUnits D8109.These enclosures have a rectangular knockout on
andAccessories-HouseholdSystemType the door, allowing installers to view the green AC power
(UL985),UTOU7:Control Units and LED on the battery charger module.
Accessories-Household System Type
CertifiedforCanada(cULus) The D137 Mounting Bracket allows installers to mount a
FM battery charger module into enclosures from other
manufacturers.
CSFM 7167-1615:100,7165-1615:119
NYC-MEA 12-92-E,Vol.IV
12-92-E,Vol.12 Parts Included
12-92-E,Vol.15 D8132 Battery Charger Module
NYC/BSA 582-85-SA
Quantity Component
Note The D8132 and D8132LT are UL rated as a 2 Cables
battery chargers only,not as a stand-alone 2 Sets LockWashers
power supplies. 2 Sets Nuts
2 Sets Screws
2 Sets Terminal Lugs
Installation/Configuration Notes 1 D1640Transformer
Compatibility Information The cables connect the D8132 to the transformer, one or
Control Panels two batteries,and the control panel.Additional hardware is
ICP-EZM2 EasySeriesl provided for connecting larger batteries.This hardware is
not required when connecting 12 VDC, 7 Ah batteries.
D9412GV2,D7412GV2,D7212GV2z
D8132LT Battery Charger Module
D9412G,D7412G,D7212G2
D9412,D7412,D7212 Quantity Component
D6412,D4412 2 Cables
D2212,D22126,D2212BE 2 Sets Lock Washers
D91243 2 Sets Nuts
D9112,D9112B1,D8112,D6112,D721261 2 Sets Screws
2 Sets Terminal Lugs
1 =Not investigated by Underwriter's Laboratories (UL).
2 = The D7212GV2 and D7212G Control Panels are not UL
Listed for Commercial Fire Applications.
3= The D9124 uses a D9412GLT8 Contro/Panel.
� ,t
�i • �i ••
Technical Specifications
Electrical
Operating Voltage 16 VAC to 18 VAC supplied by plug-in transformer
(D8132):
Operating Current: 1200 mA maximum
Float Voltage: 13.9 VDC
Mechanical
Dimensions: 12.7 cm x 7.6 cm x 2 cm(5 in.x 3 in.x 8 in.)
Ordering Information
D8132 Battery Charger Module D8132
Uses a D 164016.5 VAC,40 VA Plug-in Trans-
former to supply 1200 mA of battery charging
current.
D8132LT Battery Charger Module D8132LT
Suitabie for 12 VDC,up to 27 Ah of batteries.
Increases battery standby time.Requires a
D1640 Plug-in Transformer.
Accessories
D8004 Transformer Enclosure D8004
For applications such as fire alarm that might
require a transformer enclosure.
D137 Mounting Bracket D137
Used to mount accessory modules in D8103,
D8108A,and D8109 enclosures.
D126 Standby Battery(12 V,7 Ah) D126
Sealed lead-acid standby and auxiliary re-
chargeable power supply.
D1640 Transformer D1640
www.boschsecurity.com
r �
. . � �� � . .
��-� BOSCH
�
Invented for life
Conettix DX4020 Ethernet Network
Interface Module
I.,..r,,,,.,,.,._..
, °'� �,� � ' f ► Built•in IP-based alarm transport,programming,and
� �i�i I I j� � � `� ' � � ,µ� �r, control
,� r, :� ! ' � ;� ���',,„', ► 10BASE•T or 100BASE-T network connection
�..
,� �,, ;:�, �;�,�
�' �4 ' rr '.s �.� ``" �� � 'r.rc; ► Full-duplex and half•duplex support
�+. �.:--- ..
� �-� »a-Sa.�� �A
��"'��� ��� ,�� ��;���' ��'J '� �;i� ► Three-hole mounting pattern
� , - � .�.� �i � .;.a.
� �� � �� ��-,� 1� � ,��� 'llti �� ;;,�� ► Support for dynamic or static IP addresses
0 �,�' ��/����`���i�����t, � ► DIP switches for option bus or SDI bus address
1� �� ��� � r4 _ S�f:��jt�t��l
�: � F y���;� �„ programming
� � �� . �� ��-� � ;�;a� a k f ► Light emitting diodes (LEDs)provide control panel
� -� � status
► Supports 128•bit AES Rijndael encryption
The Conettix DX4020 Ethernet Network Interface Module System Overview
creates two-way communications over Ethernet networks
for compatible control panels.Typical uses include:
2 3
• Reporting to the Conettix D6600 Communications �
Receiver/Gateway a
• Remote administration with Remote Programming s
Software (RPS) or RPS-Lite 5 8 �
• Connecting to a PC for programming with PC9000 �� �0 9
Software or Building Integration System (BIS) Security
Engine
'�� „
1. Compatible Control Panel
2. Compatible Control Panel Option Bus or SDI Bus Connection
3. Conettix DX4020 Ethernet Network Interface Module
4. Ethernet Network Connection to DX4020
5. Host PC running Conettix D6200 Programming/Administration
Software
6. Ethernet Network Connection to Host PC Ethernet Network Interface
Card(NIC)
7. Ethernet Network,Local Area Network(LAN),Metropolitan Area
Network(MAN),Wide Area Network(WAN),or Internet
8. Ethernet Network Connection to Conettix D6680 Ethernet Network
Adapter
9. Conettix D6680 Ethernet Network Adapter
www.boschsecurity.com
a r
. � �� � . ..
10. Conettix D6680 Ethernet Network Adapter Connection to Conettix Region Certification
D6600 Communications Receiver/Gateway COM4 Port USA UL AMCX:Central Station Alarm Units
11. Conettix D6600 Communications Receiver/Gateway (UL1610,UL1635),AMCX7:Central
Station Alarm Units Certified for Canada
The system overview diagram shows a system using a
(cULus),APAW:Police Station Alarm Units
compatible control panel, Conettix DX4020 Ethernet Network (UL365,UL464),APAW7:Police Station
Interface Module, Conettix D6600 Communica[ions Receiver/ Alarm Units Certified for Canada(cULus),
Gateway, and a Conettix D6680 Ethernet Network Adapter. APOU:Proprietary Alarm Units(UL1076),
APOU7:Proprietary Alarm Units Certified
for Canada(cULus),NBSX7:Household
Functions Burglar Alarm System Units Certified for
Canada(cULus),UTOU7:Control Unitsand
LEDs Accessories-Household System Type
Certified for Canada(cULus)
Red LEDs Function
BUS-RCV Data bus receives data from control panel
UL864,9th edition
BUS-XMIT Data bus transmits data to control panel FM
Green LEDs Function CSFM 7167-1615:100,7165-1615:119,
7300-1615:180
SER-RX RS-232 receives data from serial device
SER-TX RS-232 transmits data to serial device NYC-MEA 12-92-E,Vol.XIII and 12-92-E,Vol.15
NIST FIPS 197 Certificate No.304
Four LEDs provide information about the transmission and
receipt of data. There are also two network diagnostic LEDs This product is designed to also comply with the requirements of:
that provide information about the network connection. Refer France AFNOR NF,A2P Type 2(122000076-05)
to the DX4020 Installation Guide (P/N 49522) for details Note FM Approval applies when the DX4020 is used
about the network diagnostic LED functions. with the Conettix D6600 Communications
DIP Switches Receiver/Gateway.
Use the DIP switches to easily assign a bus address to the
DX4020.
Programmable IP Address Installation/Configuration Notes
Use ARP and Telnet commands from any PC to program the Compatibility information
DX4020 IP address. The IP address can be dynamic using
DHCP or the IP address can be static. Applications
RPS: Supported on all compatible control panels.
PC9000: Supported on the following control panels:
Certifications and Approvals D9412G,D7412G,D7212G,D9112,D7412,
and D7212.
Building Integration Supported on the following SDI bus control panels
Region Certification S stem BIS Securit
y ( ) y (version 6.3 and higher):D9412GV2,
Europe CE 89/336/EEC,EN55022:1997+A2: Engine: D7412GV2,D7212GV2,D9412G,D7412G,and
2002,EN50130-4:1995+A1:1998+A2: D7212G.
2003,EN60950:2000,EN61000-3-2: CMS 7000: Supported on DS7400Xi-CHI Control Panels(op-
2001,EN61000-3-3A1:2001, tion bus)set at Mode 18(version 4.10 or higher).
EN61000-4-2:1995+A1:1998+A2:
2001,EN61000-4-3:1996+Al:1998 SDI Bus Control Panels(version 6.0 or higher)
+A2:2000,EN61000-4-4:1995+Al: • D9412GV2,D7412GV2,and D7212GV2
2001+A2:2001,EN61000-4-5:1995 • D9412G,D7412G,and D7212G
+A1:2001,EN61000-4-6:1996+Al: • D9412,D7412,and D7212
2000,EN61000-4-11:1994+A1:2001 • D9112
Belgium INCERT B-509-0005 Option Bus Control Panels
• DS7400Xi(version 4.10 or higher)
• CC7420-A
• DS7220 and DS7240(version 2.10 or higher)
• FPD-7024
�+ .
. � �� � . ..
Connection Considerations Ordering Information
The DX4020 uses a standard Category 3 or Category 5 cable D2203 Enclosure D2203
with an RJ-45 plug to connect to the network, a two-wire Grey steel enclosure with a lock.Accepts an
connection from the control panel bus, and two wires that optional tamperswitch.Measures 37 cm x
connect to the control panel or a power supply for DC 34 cm x 8.9 cm(14.6 in.x 13.4 in.x 3.5 in.).
power. For lOBASE-T, use Category 3 or better. For D8103Enclosure D8103
1006ASE-T, use Category 5 or better. D8109 Fire Enclosure D8109
Mounting Considerations Red steel enclosure measuring 40.6 cm x
The DX4020 mounts to the standard three-hole patterns in 40.6 cm x 8.9 cm(16 in.x 16 in.x 3.5 in).UL
supported control panel enclosures. With the D137 Listed.lncludesalockandkeyset.
mounting bracket,the DX4020 mounts to other enclosures.
Parts Inciuded
Quant. Component
1 Ethernet network interface module
1 Cable assembly,quick connect
1 Hardware pack
1 Literature-Installation Guide
Technical Specifications
Environmental Considerations
Dimensions: 7.6 cm x 12.7 cm(3 in.x 5 in.)
Operating Temperature: 0°C to+50°C(+32°F to+122°F)
Relative Humidity: 5%to 85%at 30°C(86°F)non-condensing
Power Requirements
Current: 10Base-T:110 mA maximum
1006ase-T:135 mA maximum
Voltage(Operating): 12 VDC nominal
Ordering Information
Conettix DX4020 Ethernet Network DX4020
Interface Module
Creates two-way communications over Ether-
net networks for compatible control panels.
Accessories
AEl Standard Enclosure(Gray) AEl
Standard gray enclosure with keyed lock.
Measures 35.6 cm x 31.8 cm x 7.6 cm(14 in.
x 12.5 in.x 3 in.).
AE2 Standard Enclosure(Red) AE2
Standard red enclosurewith keyed lock.Meas-
ures35.6cmx31.8cmx7.6cm(14in.x
12.5 in.x 3 in.).
AE4 Large Enclosure(Red) AE4
Large red enclosurewith keyed lock.Measures
52.7 cm x 38.1 cmx 10.8 cm(20.7 in.x 15 in.
x4.25 in.).
www.boschsecurity.com
� � I � ��• .� • • •- • • • �- • .•
���� BOSCH
�
Invented for life
D7050 Series Addressable Photoelectric
Smoke and Smoke Heat Detector Heads
—T�''1 ► Connects to the multiplex bus of the D7024
».�^.::,�::
Addressable FACP
'� r\ ► Superior dust immunity
� ' '/ ► Exclusive Chamber Check self-diagnostics
r
� ' � r� ► Automatic sensitivity test features
�� � '� : 1� ► Easy disassembly for cleaning
� ����
�
�
The D7050 Photoelectric Smoke and Smoke Heat Detector Functions
Heads are UL Listed, open-area photoelectric smoke Detector Head and Base System
detectors designed for use with commercial fire protective
signaling systems and household fire warning systems (see The D7050 Photoelectric Smoke and Smoke Heat Detector
NFPA 72, the National Fire Alarm Code).They are Heads are part of a compound system of detector head and
compatible with the D7024 Addressable Fire Alarm Control base.The detector base instalis over a back box and
Panels (FACPs). contains all the wiring.The detector head attaches to the
base by aligning the head with the base and turning it
They detect large smoke particles by scattering light from a clockwise. No tools are required for installation other than
pulsed infrared source operating with a gated, high-speed, the hex key used to tighten the tamper screw.Each detector
photodiode infrared sensor.The symmetry of the optical head requires a D7050-B6 detector base.
chamber allows 360° uniform smoke entry, but minimizes Chamber Check Self-diagnostics
external light entry.
The detector meets NFPA guidelines for sensitivity testing,
Use both of these smoke detectors for detection circuits because you can visually inspect the detector and check the
installed in areas where personnel are present.The flash rate of the LED.If the calibration is out of factory-listed
D7050TH has an added fixed-temperature sensor.This range,the LED on the detector double flashes once every 3
expands the detector application to confined areas where sec to 8 sec. Follow the instructions provided with the
a fire increases air temperature slowly and where there is a detector to clean it.The detector also sends a dirty chamber
substantial increase in air temperature before the fire report to the control panel.
breaks confinement, such as furnace rooms, closets, and
other confined areas. LED Operation
When the detector is operating normally, the LED flashes
once every 3 sec to 8 sec. In alarm, the detector flashes at
least once per second.
Magnetic Test Feature
Test the detector's operation by placing the SMK-TM Test
Magnet next to the detector's LED for three consecutive
flashes.This causes the detector to send an alarm.
www.boschsecurity.com
� I I ��• .• • • •- • • • �- • .•
Certifications and Approvals Mechanical Properties
Color: Off-white
Region Certification Dimensions(diame- 4 in.x 1.3 in.(10.2 cm x 3.3 cm)
Europe CE 89/336/EEC,EN55022:1998, ter x D):
EN50130-4:1995,EN60950:2000, Material: High-impact,fire-retardant ABS plastic
EN61000-3-2,EN61000-3-3,
EN61000-4-2,EN61000-4-3, Power Requirements
EN61000-4-4,EN61000-4-5, Current(alarm): 0.55 mA maximum
EN61000-4-6,EN61000-4-11
Current(standby): 0.55 mA nominal
USA UL UROX:Smoke-Automatic Fire Detectors power-up Time: 22 sec maximum
(UL268and A),UROX7:Smoke-Automatic
Fire Detectors Certified for Canada Voltage(minimum): 8 VDC peak from the multiplex bus
(cULus) Trademarks
FM Trademark names are used throughout this document. In
CSFM 7272-1615:175 most cases, these designations are claimed as trademarks
NYC-MEA 12-92-E,Vol.14 or registered trademarks in one or more countries by their
Hong Kong HKFSD respective owners. Rather than placing a trademark symbol
in every occurrence of a trademark name, Bosch Security
Systems, Inc. uses the names only in an editorial fashion
and to the benefit of the trademark owner with no intention
Installation/Configuration Notes of infringing the trademark.
Compatible Products
Chamber Check is a registered trademark of Bosch Security Systems in the
The following products are compatible with the D7050 UnitedStates.
Smoke Detector and the D7050TH Smoke Heat Detector:
Category Product ID Product Description
Control Panels D7024 FACP Ordering Information
D7024-EXP FACP for export D7050 Addressable Photoelectric Smoke D7050
Detector Bases D7050-B6 Two-wire base Detector Head
Two-wire,UL Listed,open-area smoke detec-
Remote DRA-12/24 12/24 VDC remote annunciator tor head for use with the D7024 Addressable
Annunciators Fire Alarm Control Panels:requires a D7050-
B6 base.
D7050TH Addressable Photoelectric D7050TH
Parts Included Smoke and Heat Detector Head
Two-wire,UL Listed,open-area smoke detec-
Quant. Component tor head with a 135°F(57°C)fixed tempera-
1 Detector head ture heat sensor for use with the D7024 Ad-
dressable Fire Alarm Control Panels;requires
1 Literature pack a D7050-B6 base.
Accessories
DRA-12/24 Remote Annunciator DRA•12/24
Technical Specifications (12/24VDC)
Environmental Considerations Designed to provide remote annunciation of
alarms when connected to the D7050-B6 Mul-
Radio Frequency Interfer- No alarm or setup on critical frequencies in the tiplex Detector Base
ence(RFI)Immunity: range of 26 MHz to 950 MHz forfield strengths DT-2 Detector Removal Tool DT-2
less than 50 V/m Use the DT-2 to remove,replace,or test the
Temperature +32°F to+100°F(0°C to+38°C) detector head
(normal operating): SMK-TM Test Magnet SMK-TM
Note:The environment where these detectors are installed must be within Used to test detectors
the specified normal operating temperature limits.
� � � I C. • - �- - •
�� BOSCH
�
Invented for life
D7050-B6 Two-wire Detector Base
� ► Connects to multiplex bus of the D7024 Addressable
FACP
.
� ► Detector's head is easily removed by twisting
ti' ► Two-piece detector head and base design allows
pre•wiring the system
�
�'���� -���
� �
���� �' .
�����
��
�
�
The D7050-66 is the required base for the D7050 Multiplex Installation/Configuration Notes
Photoelectric Smoke Detector Head and the D7050TH Compatible Products
Multiplex Photoelectric Smoke Heat Detector Head. It
connects to the multiplex bus of the D7024 Addressable The following products are compatible with the D7050-B6
Fire Alarm Control Panels (FACPs).
detector base:
Note The D7024 FACP requires a D7039 MUX Category ProductlD ProductDescription
Expansion Module and control panel ROM Control D7024 FACP
version 2.0 or higher. Panels D7024-EXP FACPforexport
Detectors D7050 Multiplexphotoelectricsmokedetector
D7050TH Multiplex photoelectric smoke detector
Certifications and Approvals with 135°F(57°C)heat sensor
Remote DRA-12/24 12 VDC and 24 VDC remote annunciator
Region Certification Annunciators
Europe CE 89/336/EEC,EN55022:1998, Mounting Considerations
EN50130-4:1995,EN60950:2000, The D7050-B6 Base can be mounted on a four-inch square,
EN61000-3-2,EN61000-3-3, a four-inch octagonal, or a single-gang box. It can also be
EN61000-4-2,EN61000-4-3, surface mounted with anchors, mollies, or wing nuts.
EN61000-4-4,EN61000-4-5, Number of Devices Allowed on Loop
EN61000-4-6,EN61000-4-11
The number of multiplex smoke or smoke-heat detectors
USA UL UROX:Smoke-AutomaticFireDetectors allowed on the multiplex bus is determined by the wire
(UL268andA),UROX7:Smoke-Automatic gauge and the total wire length of the bus. Do not exceed
FireDetectorsCertifiedforCanada 30 II maximum line resistance. Refer to the D7039
(cULus)
Installation Guide (P/N: 38685)for multiplex bus wiring
FM requirements.
CSFM 7300-1615:176 Wiring Connection to D7024 MUX bus through D7039
NYC-MEA 12-92-E,Vol.14
Warning Do not use shielded cable.
www.boschsecurity.com
� 1 � C• • �- •
The D7050-66 bases can be wired in a series or using the Ordering Information
T-tap method. See the following illustrations. D7050-B6Two-wireDetectorBase D7050-B6
Required base for the D7050 Multiplex Pho-
_- , toelectric Smoke Detector Head and the
\ D7050THMuItiplexPhotoelectricSmokeHeat
�°�` ' "' °� Detector Head
x � ��
m x w ;� l��
� x \ �
x
Series Connection
� _
�
x �
m x �
� x
x •
T-tap Connection
Parts Included
Quant. Component
1 Detector base
1 Hardware pack
1 Literature pack
Technical Specifications
Environmental Considerations
Relative Humidity: 0%to 93%non-condensing
Temperature(Operating): +32°F to+100°F(0°C to+38°C)
Mechanical Properties
Color: Off-white
Material: High-impact,fire-retardant polymer plastic
Amaricas: Europe,Middle East,Africa: AsirPacifie: Represented by
Bosch Security Systems,Int. Bosch Seturity Systems B.V. Robert Bosch(SEA)P[e Ltd,Security Systems
130 Perinton Parkway P.O.Box 80002 11 Bishan Street 21
Fairport,New York,14450,USA 5600 JB Eindhoven,The Netherlands Singapore 573943
Phone:+1 800 289 0096 Phone:a 31 40 2577 284 Phone:+65 6258 5511
Fax:.1 585 223 9180 Fax:i31 40 2577 330 Fax:♦65 6319 3499
securiry.sales(�us.bosch.com emea.securitysystems�bosch.com apr.securitysystems(�bosch.com
www.bosthsecurity.us www.boschseturity.com www.boschsewrity.com
�Bosch Security Systems Inc.2009�Data subject to change without notice
T1314228747(Cur:en-U5,V3,27 Ott 2009
� •1� �- •
(��� BOSCH
�
Invented for life
5600 Series Mechanical Heat Detectors
► Post-activation i�dicator to easily identify units in
alarm
► Multiple configurations satisfy a broad range of
installations
► Broad range of back box mounting options
► Reversible mounting bracket for surface-mount or
flush•mount installations
� ,� k � 1
•
�� r
�y
The System Sensor 5600 Series Mechanical Heat Detectors Certifications and Approvals
provide low-cost property protection against fire and non- System Sensor holds these Listings and Approvals:
life-safety installations where smoke detectors are
inappropriate.
Region Certification
Warning For life-safety installations, smoke detectors USA UL UQGS:Heat-AutomaticFireDetectors
must be used in lieu of or in addition to heat (UL521)
detectors.
FM
CSFM 7270-1653:167
Functions NYC/MEA 199-03-E
Detector Labeling
The 5601P has a plain, unlabeled housing and is intended
for residential applications. All other models have labeled Installation/Configuration Notes
housings to ensure that the proper detector is being used. Compatibility Information
Alphanumeric characters identify the activation method (FX The 5600 Series Mechanical Heat Detectors are compatible
for fixed temperature or FX/ROR for combination fixed with all UL Listed Fire Alarm Control Panels (FACPs).
temperature and rate-of-rise units) and the temperature Mounting Considerations
rating in degrees Fahrenheit and degrees Celsius.
Mount the detectors on ceilings using 3.5-inch or 4-inch
Post-activation Fixed-temperature Indicator octagonal back boxes, single-gang boxes,or 4-inch square
When the detector is activated,the collector drops from the back boxes with a square-to-round plaster ring. The
unit.This allows easy identification of all units in alarm. mounting bracket is reversible for use in either surface-
Note The fixed-temperature sensors cannot be reset mount or flush-mount installations.
so they are not testable.The rate-of-rise Wiring Considerations
sensors automatically reset and can be tested The terminal blocks accept wires from 14 AWG (1.8 mm)to
if care is taken to avoid exceeding the fixed- 22 AWG (0.8 mm).
temperature setting of the detector.
www.boschsecurity.com
•11 �- •
Parts Included Ordering Information
Quant. Component 5601P Single-circuit,Fixed-temperature 5601P
(+135°F),Rate-of-rise Mechanical Heat
1 Mechanicalheatdetector Detector
1 Literature pack System Sensor�single-circuit fixed-tempera-
ture(+135°F),rate-of-rise mechanical heat
detector.
Technical SpecifiCations 5602 Single-circuit,Fixed-temperature 5602
(+194°F),Rate-of-rise Mechanical Heat
Contact Ratings Detector
System Sensor�single-circuit,fixed-tempera-
Contact Ratings ture(+194°F),rate-of-rise mechanical heat
6 VAC to 125 VAC: 3 A detector.
6 VDC to 28 VDC: 1 A 5603 Single-circuit,Fixed-temperature 5603
(+135°F)Mechanical Heat Detector
125 VDC: 0.3 A System Sensor�single-circuit,fixed-tempera-
250 VDC: 0.1 A ture(+135°F)mechanical heat detector.
Environmental Considerations 5604 Single-circuit,Fixed-temperature 5604
(+194°F)Mechanical Heat Detector
Relative Humidity: 5%to 95%,non-condensing System Sensor°single-circuit,fixed-tempera-
Temperature(installation) ture(+194°F)mechanical heat detector.
+135°F(+57°C)Models: The normal ambient temperature is not to ex- 5621 Dual-circuit,Fixed-temperature 5621
ceed+100°F(+38°C) (+135°F),Rate-of-rise Mechanical Heat
+194°F(+90°C)Models: The normal ambient temperature is not to ex- Detector
ceed+150°F(+66°C) System Sensoro dual-circuit,fixed-tempera-
ture(+135°F),rate-of-rise mechanical heat
Mechanical Properties detector.
Dimensions 4.6 in.x 1.7 in.(11.6 cm x 4.4 cm) 5622 Dual-circuit,Fixed-temperature 5622
(with mounting bracket): (+194°F),Rate-of-rise Mechanical Heat
Detector
Rate-of-rise Threshold: +15°F(+8.3°C)per min. System Sensor�dual-circuit,fixed-tempera-
Weight: 6 oz(170 g) ture(+194°F),rate-of-rise mechanical heat
Power Requirements detector.
5623 Dual•circuit,Fixed-temperature 5623
Voltage(operating): 6 VAC to 125 VAC,6 VDC to 28 VDC,125 VDC, (+135°F)Mechanical Heat Detector
or 250 VDC System Sensora dual-circuit,fixed-tempera-
Trademarks ture(+135°F)mechanical heat detector.
Trademark names are used throughout this document. In 5624Dual-circuit,Fixed•temperature 5624
most cases, these designations are claimed as trademarks (+194°F)MechanicalHeatDetector
or registered trademarks in one or more countries by their SystemSen�sor�dual-circuit,fixed-tempera-
ture(+194 F)mechanical heat detector.
respective owners.Rather than placing a trademark symbol
in every occurrence of a trademark name, Bosch Security
Systems, Inc. uses the names only in an editorial fashion
and to the benefit of the trademark owner with no intention
of infringing the trademark.
System Sensor is a registered trademark or trademark of System Sensor,a
brand of Honeywell International Inc.,in the United States and other coun-
tries.
Amarlcas: Europa,Mlddle East,Africa: AslrPaciflc: Representad by
Bosch Security Systems,Inc. Bosth Sxurity Sys[ems B.V. Rabert Bosch(SEA)Pte Ltd,Security Sys[ems
130 Perinton Parkway P.O.Box 80002 11 Bishan Street 21
Fairport,New York,14450,USA 5600 JB Eindhoven,The Netherlands Singapore 573943
Phone:tl 800 289 0096 Phone:+31 40 2577 284 Phone:+65 6571 2600
Fax:+1 585 223 9180 Fax:+31 40 2577 330 Fax:r65 6571 2698
security.sales�us.bosch.com emea.securitysystems@bosch.com apr.securitysystems�bosch.com
www.boschsecurity.us www.boschsecurity.com www.boschsecurity.com
�Bosch Security Systems Inc.2009 I Data subject to change without notice
T3227842827�Cur:en-US,V5,3 Dec 2009
� I� � - � . •
'��- BOSCH
�
Invented for life
FMM-100 Series Die-cast Metal Fire Alarm
Manual Stations
____
► Single or dual action
a� , � ` � "° � s. �
' ± � ► Terminal connections
PUSH ' Gold-plated alarm contacts for corrosion resistance
► Surface or weatherproof back boxes
t'u � LL
'� : , '�
' � I'ULL
The FMM-100 Series is a family of versatile, high-quality, Certifications and Approvals
metal fire alarm manual stations. Single-action or
dual-action models are available.All models come with a key Region Certification
lock and contain gold-plated contacts to resist corrosion.
USA UL UNIU:Boxes.Non-Coded(UL38),UNIU7:
Boxes,Non-Coded Certified for Canada
(cUlus)
Functions CSFM 7150-1615:224
Operation NYC-MEA 382-94-E or 382-94-E,Vol.3
Single-action
When the bar on the front of the manual station is pulled, it
latches open and is easily visible from 50 ft (15 m). Reset Installation/Configuration Notes
the activation bar by opening the manual station with the
key and placing the activation bar in its normal upright Compatibility Information
position.An optional scored acrylic break rod is available. Compatible with all Bosch Security Systems,Inc.Fire Alarm
Control Panels.
Dual-action
Mounting Considerations
With the dual-action configuration the upper bar on the The FMM Series manual stations can be surface mounted
front of the manual station rotates inward allowing the on either the FMM-10066-R Surface-mount Back Box or the
activation bar to be grasped and operated by a single hand. FMM-100WPB6-R Weatherproof Back Box.They can also be
flush mounted on a standard single-gang back box.
Note When properly mounted on the
FMM-100WP6B-R Weatherproof Back Box,
these manual stations meet UL requirements
for outdoor use.
www.boschsecurity.com
11 � � •
To comply with ADA standards,the manual station must be Ordering Information
less than 48 in. (1.2 m)above the floor for front wheelchair FMM-100SATKSingle-action Manual FMM-100SATK
access and less than 54 in. (1.3 m) above the floor for side Station(red)
wheelchair access. Versatile,high-quality,metal single-action fire
alarm manual station with key lock and
gold-plated contacts
Parts Included FMM-100SATK-NYCSingle-actionManual FMM-100SATK-NYC
Station for New York City
Quant. Component Versatile,high-quality,metal single-action fire
alarm manual station for New York City with key
1 Manual station lock and gold-plated contacts
1 D102 Key(1358 key) FMM-SOODATK Dual-action Manual Station FMM-100DATK
1 FMM-100GR Acrylic Break Rod (red)
1 Hardware pack Versatile,high-quality,metal dual-action fire
1 Literature pack alarm manual station with key lock and
gold-plated contacts
Accessories
Technical SpeCifications D102 Replacement Key D102
Replacement key(#1358)for the D 101 lock.
Environmental Considerations FMM-SOOBB-R Surface-mount Back Box FMM-100BB•R
Relative Humidity: 90%at+100°F(+38°C) (red)
Red cast-metal back box
Temperature(operating): -40°F to+150°F(-40°C to+66°C) FMM•100WP6B-R Weatherproof Back Box FMM•300WPBB•R
MechanicalProperties (red)
Color: Red
Red cast-metal weatherproof back box
FMM-100GR Scored Acrylic Break Rods FMM-100GR
Dimensions(H x W x D): 4.75 in.x 3.25 in.x 1.1 in. Scored acrylic rods(12 per package)
(12cmx8.3cmx2.8cm)
Material: die-cast metal
Inputs
Switch Rating: 1 A at 30 VDC or 125 VAC
Amertcas: Europs,Middla East,Afrlca: AslrPaclf(c: papresented by
Bosch Security Systems,Inc. Bosth Security Sys[ems B.V. Robert Bosch(SEA)Pte L[d,Security Systems
130 Perinton Parkway P.O.Boz 80002 11 Bishan Street 21
Fairport,New Vork,14450,USA 5600 JB Eindhoven,The Netherlands Singapore 573943
Phone:.1 800 289 0096 Phone:+31 40 2577 284 Phone:.65 6571 2600
Fax:+1 585 223 9180 Fax:+31 40 2577 330 Fax:+65 6571 2698
security.sales�us.bosch.com emea.securitysystems�bosch.com apr.securi[ysystems@bosch.com
www.bosthseturity.us www.boschseturity.com www.boschsecurity.com
8 Bos[h Security Systems Inc.2009 I Data subject to change without notice
T2363731851 I Cur:en-US,V�,3 Dec 2009
7
�
0
. .
�
COOPER Notification
��
ED � Finally, Design and Safety Meet...
r- ,
� � � ��
� � • � + ��`�'• �� �
�,. � i t � .. .� .
. ..`. � _.,.:
. �~
�1�t� �_a.__.
Ceiling Wall
Description:
The Wheelock�'ExcederTM'Series of notification appliances feature
a sleek modern design that will please building owners with reduced - Save up to t�$% in current draw*
total cost of ownership. Installers will benefit from its comprehensive
feature list, including the most candela options in one appliance,
low current draw,no tools needed for setting changes,voltage test - UP t0 9 models now in 1 appliance
points,12/24 VDC operation,universal mounting base and multiple
mounting options for both new and retrofit construction. p 14% **
- Save u to cost of installation
The Wheelockk�"ExcederTM' Series incorporates high reliability and
high efficiency optics to minimize current draw allowing for a greater
number of appliances on the notification appliance circuit.All strobe
models feature an industry first of 8 candela settings on a single � Sleek Modern Aesthetics
appliance.Models with an audible feature 3 sound settings(90,95,
99 dB).All switches to change settings,can be set without the use
of a tool and are located behind the appliance to prevent tampering. �� Finger Slide Switches
Wall models feature voltage test points to take readings with a
voltage meter for troubleshooting and AHJ inspection.
The Wheelock� ExcederTM' Series of wall and ceiling notification � Voltage Test Points
appliances feature a Universal Mounting Base (UMB) designed
to simplify the installation and testing of horns, strobes, and
combination horn strobes. The separate universal mounting � Multiple Voltages
base can be pre-wired to allow full testing of circuit wiring before '
the appliance is installed and the surface is finished. It comes
complete with a Contact Coverfor protection against dirt,dust,paint � 3 Audible Settings
and damage to the contacts. The Contact Cover also acts as a so,ss,99 dB
shunting device to allow pre-wire testing for common wiring issues.
The Contact Cover is polarized to prevent it from being installed
incorrectly and prevents the appliance from being installed while 8 Candela Settings"'
it is on the UMB. When the Contact Cover is removed the circuit � Wall-15/1575/30/75/95/110/135/185
will show an open until the appliance is installed.The UMB allows Ceiling-15/30/60/75/95/115/150/177
for consistent installation and easy replacement of appliances if
required. Wall models provide an optional locking screw for extra ,� ,�� Universal Mounting Base """
secure installation, while the ceiling models provide a captivated l�, Ceiling and Wall
r� Mounts to 5 Backbox Types
screw to prevent the screw from falling during installation.
� Environmentally Friendly
Low Current Draw
Compatibility and Requirements
-Synchronize using the Wheelock�Sync Modules or panels with built-in Wheelock�Patented Sync Protocol
-Compatible with UL"Regulated Voltage" using filtered VDC or unfiltered VRMS input voltage
-Strobes produce 1 flash per second over the"Regulated Voltage" range
*Compared to competitive models "'*Patented
'*Compared to previous models
��
�
NOTE:All CAUTIONS and WARNINGS are identified by the symbol r.All warnings are printed in boid capital letters.
A WARNING: PLEASE READ THESE SPECIFICATIONS AND ASSOCIATED INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING,SPECIFYING
OR APPLYING THIS PRODUCT. VISIT WWW.COOPERNOTIFICATION.COM OR CONTACT COOPER NOTIFICATION FOR THE CURRENT INSTALLATION
INSTRUCTIONS. FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS,CAUTIONS OR WARNINGS COULD RESUIT IN IMPROPER APPLICATION,
INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION,WHICH COULD RESULT IN PROPERTY DAMAGE,AND
SERIOUS INJURY OR DEATH TO YOU ANO/OR OTHERS.
General Notes:
General Notes:
•Strobes are designed to flash at 1 flash per second minimum over their"Regulated Voltage Range".
•All candela ratings represent minimum effective strobe intensity based on UL Standard 1971.
•Series Exceder Strobe products are Listed under UL Standards 1971 and 464 for indoor use with a temperature range of 32°F to 120°F(0°C to 49°C)and
maximum humidity of 93%(t 2%)UL 464(85%UL 1971).
•Series Exceder horns are under UL Standard 464 for audible signal appliances(Indoor use only).
• � � • • •
Strobe Ratings per UL Standard 1971
24 VDC/24 FWR 12 VDC
Model Regulated Voltage 15 15/75 30 60 75 95 110 115 135 150 177 185 15 15/75
Range VDC
ST 8.0-33.0 0.057 0.070 0.085 0.135 0.163 0.182 0.205 0.253 0.110 0.140
STC 8.0-33.0 0.061 0.085 0.103 0.135 0.163 0.182 0.205 0.253 0.110
Horn Strobe Ratings per UL 1971 &UL 464 at 24 VDC
.. �:.
24 VDC 12 VDC
Model Regulated Voltage 15 15/75 30 60 75 95 110 115 135 150 177 185 15 15/75
Range VDC
HS 8.0-33.0 0.082 0.095 0.102 0.148 0.176 0.197 0.242 ' 0.282 0.125 0.159
HSC 8.0-33.0 0.082 0.102 0.141 0.148 0.176 0.197 0.242 0.282 0.125
- .:
24 VDC 12 VDC
Model Regulated Voltage �5 15/75 30 60 75 95 110 115 135 150 177 185 15 15/75
Range VDC
HS 8.0-33.0 0.073 0.083 0.087 0.139 0.163 0.186 0.230 " 0272 0.122 0.153
HSC 8.0-33.0 0.073 0.087 0.128 0.139 0.163 0.186 0.230 0.272 0.122
•� .:
24 VDC 12 VDC
Model Regulated Voltage 15 15/75 30 60 75 95 110 115 135 150 177 185 15 15/75
Range VDC
HS 8.0-33.0 0.065 0.075 0.084 0.136 0.157 0.184 0.226 �, 0.267 0.120 0.148
HSC 8.0-33.0 0.065 0.084 0.120 0.136 0.157 0.184 0.226 0.267 0.120
Horn Ratings per UL 464 �► �
� �
Re ulated Volta e � " ` �'
Model g 9 99 dB 95 dB 90 d6 `� I � ,
Range VDC " � � �� �� � �� �� �
�� � - -� :
HN 16-33.0 0.064 0.044 0.022 �� .�
HNC 16-33.0 0.084 0.044 0.022 � ��"" �'� � '�� �"'��� ��
ii,�
HN 8.0-17.5 0.047 0.026 0.017
HNC 8.0-17.5 0.047 0.026 0.017
`UL max current rating is the maximum RMS current within the listed voltage range(16-33 VDC for 24 VDC units). For strobes the
UL max current is usually at the minimum listed voltage(16 VDC for 24 VDC units). For audibles the max current is usually at the
maximum listed voltage(33 VDC for 24 VDC units). For unfiltered ratings, see installation instructions.
��
Specification 8� Ordering Information
Strobe Sync w/SM, Mounting
Model Candela DSM or 12/24 VDC* Options
PS-6&PS-8
. ..-
HSR 15/1575/30/75/95/110/135/185 X X UMB'"
• HSW 15/1575/30/75/95/110/135/185 X X UMB"'
� HSRC 15/30/60/75/95/115/150/177 X X UMB"
.
HSWC 15/30/60/75/95/115/150/177 X X UMB"
. ..-
STR 15/1575/30/75/95/110/135/185 X X UMB"
� STW . 15/1575/30/75/95/110/1351185 X X UMB"
� STRC 15/30/60/75/95/115/150/177 X X UMB"
' STWC 15/30/60/75/95/115/150/177 X X UMB'*
� HNR X X UMB**
HNW X X UMB"'
HNRC X X UMB'*
HNWC X X UMB**
*12 VDC models feature 15 8 15/75 settings **UMB=Universal Mounting Base
Model Legend � � '� `�� � �
HN = Horn
� � � � r �r;'-J .* :�
ST = Strobe ;� ""` �� � ^+
HS = Horn Strobe � � �`
C = Ceiling Mount ` ,� ,, "'` -•'�"`
W = White '�F �
t'� . �
R = Red ''����� �> .
� , �/' _ ,��'
. �:,: /�` .
Example 1: STRC=Strobe, Red, Ceiling Mount . � �-.,'� �
Example 2: HSR= Horn Strobe, Red,Wall Mount �`" _ �
Example 3: HSW= Horn Strobe,White,Wall Mount Example: HSR Example: HSWC
� � � � ` +. ���_ . - � � �: �
� � � �
�� f ��. � ��� �
� '� � . �
t� , ,. � ��� �'r
_. �y ., i
� > . �
� �., 'Mx'r �.' _5 � �
� �_.��.- r_�:�s,
"°' ''UMB Contact Cover
. . . - . . . . . : , - . . . . . . - .
. . . . . . - . . . . . . .
- . . . - .
NOTE:Due to continuous development of our products,specifcations and offerings are subject to change without notice in accordance
with Cooper Wheelock Inc.,dba Cooper NotiFcation standard terms and conditions.
� �
Architects and Engineers Specifications
The notification appliances shall be Wheelock� ExcederT"'Series HS Audible Strobe appliances, Series ST Visual Strobe appfiances
and Series HN Audible appliances or approved equals.The Series HS and ST Strobes shall be listed for UL Standard 1971 (Emergency
Devices for the Hearing-Impaired)for Indoor Fire Protection Service. The Series HS and HN Audibles shall be UL Listed under Standard
464 (Fire Protective Signaling). All Series shall meet the requirements of FCC Part 15 Class B.All inputs shall be compatible with
standard reverse polarity supervision of circuit wiring by a Fire Alarm Control Panel(FACP)with the ability to operate from 8 to 33 VDC.
Indoor wall models shall incorporate voltage test points for easy voltage inspection.
The Series HS Audible Strobe and ST Strobe appliances shall produce a flash rate of one (1)flash per second over the Regulated
Voltage Range and shall incorporate a Xenon flashtube enclosed in a rugged LexanO lens.The Series shall be of low current design.
Where Multi-Candela appliances are specified, the strobe intensity shall have 8 field selectable settings at 15, 15/75, 30, 75, 95, 110,
135, 185 candela for wall mount and 15, 30, 60, 75, 95, 115, 150, 177 candela for ceiling mount. The selector switch for selecting
the candela shall be tamper resistant. The 15/75 candela strobe shall be specified when 15 candela UL Standard 1971 Listing with
75 candela on-axis is required (e.g.ADA compliance). Appliances with candela settings shall show the candela selection in a visible
location at all times when installed.
The audible shall have a minimum of three(3)field selectable setti�gs for dBA levels and shall have a choice of continuous or temporal
(Code 3)audible outputs.
The Series HS Audible Strobe,ST Strobe and Series HN Audible shall incorporate a patented Universal Mounting Base that shall allow
mounting to a single-gang, double-gang,4-inch square, 3.5-inch octal, 4-inch octal or 100mm European type back boxes. Two wire
appliance wiring shall be capable of directly connecting to the mounting base. Continuity checking of the entire NAC circuit prior to
attaching any notification appliances shall be allowed. Product shall come with Contact Cover to protect contact springs. Removal of
an appliance shall result in a supervision fault condition by the Fire Alarm Control Panel(FACP). The mounting base shall be the same
base among all horn, strobe, horn strobe,wall and ceiling models. All notification appliances shall be backwards compatible.
The Series HS and ST wall models shall have a low profile measuring 5.24"H x 4.58"W x 2.19"D. Series HN wall shall measure 5.24"
H x 4.58"W x 1.6" D. The Series HSC and STC shall been round and have a low profile with a diameter of 6.68"x 2.63" D. Series
HNC ceiling shall have a diameter of 6.68"x 1.50" D.
When synchronization is required,the appliance shall be compatible with WheelockOO's SM, DSM Sync Modules,WheelockO Power
Supplies or other manufacturer's panels with built-in Wheelock�Patented Sync Protocol.The strobes shall not drift out of synchronization
at any time during operation. If the sync protocol fails to operate, the strobe shall revert to a non-synchronized flash-rate and still
maintain (1)flash per second over its Regulated Voltage Range.The appliance shall also be designed so that the audible signal may
be silenced while maintaining strobe activation when used with WheelockOO synchronization protocol.
Wall Appliances—UL Standard 1971, UL Standard 464, California State Fire Marshal(CSFM), ULC
Ceiling Appliances—UL Standard 1971, UL Standard 464, California State Fire Marshal (CSFM), ULC
��ii+�'
1��:'"�
WE ENCOURAGE AND SUPPORT NICET CERTIFICATION
3 YEAR WARRANTY
Exceder- Spec Sheet 11/09
- - -� �
� � � -
:�� ��
' � �
,,,���.����". r . .
CooperNotification is WFl@@IOCI(�O �EPATH� WAVES, � COOPERNotification
A I t ro n i x� AL602ULADA, AL802ULADA, AL 1002ULADA
' NAC Power Extenders
Rev AL602/802/1002ULADA-AOSI
Overview
The AL602ULADA,AL802iJLADA and AL1002ULADA are extremely cost
! effective voltage regulated remote NAC Power Extenders.They may be connected
��' to any 12 or 24 volt Fire Alarm Control Panel (FACP). Primary applications
A include Notification Appliance Circuit (NAC) expansion (supports ADA
_ �.r=,�,
� �' requirements) and will provide auxiliary power to support system accessories.
.�� z '
��" p� AL602ULADA AL802ULADA AL 1002ULADA
��
� � � • 24VDC or 12VDC • 24VDC or 12VDC • 24VDC rated
rated @ 6.5 amp max. rated @ 8 amp max. @ 10 amp max.
• Two(2)Class A or • Two(2)Class A or • Two (2)Class A or
four(4)Class B outputs. four(4)Class B outputs. four(4)Class B outputs.
AL602ULADAJ AL802ULADAJ AL1002ULADAJ
• Larger enclosure. • Larger enclosure. • Larger enclosure.
Saecifications
• Two (2) Class A or two (2) Class B FACP inputs. • Temporal Code 3 Mode.
• Two (2)NC dry contact trigger inputs • Steady Mode.
(AL802ULADA and AL 1002LTLADA only) • Input to Output Follower Mode (maintains
• Two (2) Class A or four(4) Class B synchronization of notification appliance circuits).
indicating circuits. • March Time.
• Two (2) Class B outputs may be paralleled for more • Compatible with 24VDC or 12VDC fire panels.
power on an indicating circuit. • Common trouble inputs and outputs.
• One (1)Aux. Power Output @ 1 amp supply current • Ground fault detection.
(w/battery back up). • Input 115VAC.
• Signal Circuit Trouble Memory- facilitates quickly • AC fail supervision (form "C" contacts).
locating intermittent system trouble and eliminates • Low battery supervision (form "C" contacts).
costly and unnecessary service calls. LED's indicate a • Battery presence supervision (form "C" contacts).
prior fault (short, open, ground) has occurred on one • Power supply, logic board, red enclosure, cam lock,
or more signaling circuit outputs. transformer& battery leads.
• 2-wire Horn/Strobe Sync mode allows audible • Enclosure:
notification appliances(Horns) to be silenced while - Combination knockouts re 1/2" and 3/4"
visual notification appliances (Strobes) continue - Accommodates up to two (2)
to operate. 12VDC/12AH batteries.
• Horn/Strobe sync protocols include: Gentex�,
System Sensor�, Faraday,Amseco.
Agency Approvals
UL Listed Control Units and Accessories
U` for Fire Alarm Systems (UL 864), �� California State Fire Marshal Approved.
UL Listed Standard for Safety for Fire
Protective Signaling Systems (UL 1481).
M EA NYC Department of Buildings Approved. FM Factory Mutual Approved.
Approved �pp�
Enclosure Dimensions
AL602iJLADA,AL802ULADA and AL1002ULADA: 15.5"H x 12"W x 4.5"D
00 0000000a
aoo oa°o o a
°o°a°o o°o
000000 �
oa o°oo
"r °o°o o°o 0
°000000
°o°00000
°o°00000
000000
a0000°o
00000a
°o o°o°o 0 0
�
AL602iJLADAJ,AL802ULADAJ and AL 1002ULADAJ: 18"H x 14.5"W x 4.625"D
iaso
�.w• _zso ,�u i so
� � � �
—�i�v —��.00� —i.w.1 i.ss•I—
i.�o � �.� � � �i � � ,
I Z '
I
B.i• I
6.00•
Qo o a o0
I8.00• � I8.00• � I8.00•
I I
I
I
I
�, � � �
I.L 1.
-{I.00 I.N1�
14.50
� � �
2.]5 d, dS0 2.]5
�
International Ministerial Fellowship
2477 Shadywood Road
Navarre, MN 55392
Date: 6/24/10 Main Level - Fire System Plan
lvAr�
9 � •
� � 12
�
AGG�T/NG
lm3
DIOI
��
mi
E � o�
= D105
104
D103
!�7
p� � DI7l
KEY Scale: 1/16" = 1'-0"
k_; � 60
•P Smoke Detector J ,p�C rION/
�
• mi
Heat Detector omi
❑ D102
Pull Station vE$tjBULE
� �'e�� oi
Horn/Strobe �
■ Strobe only
� FireAnnunciatorKeypad � ���
r¢e
is 0 so
Biue Numbers =Zone# �,
� ° i i
» ie 0
� � I I Q0 E
piii = I I
L J DI13
F p? ' pl DIJ7
��� DII3 //9
� DII4 �
30 CD
�m
�. N�1'
D115 �µ
3oCo E
i�
DIIb DIIB DII9
u.era�c c r c r um
� i� �w
ra ��
� � � •. BA�NT
� m
DI14 � e�ner.cotitrwe ereren ��� D126
DI75
� � /
International Ministerial Fellowship
2477 Shadywood Road
Navarre, MN 55392
Date: 6/24/10 Upper Level - Fire System Plan
� .
E
s¢�
�
D701
� D200 �
� �Y
lmi 30 C
PROPOSED
NEW DEGK
W/ADA RAMP I
J
I
�I TINCs
GES
am
KEY Scale: 1/16" = 1'-0"
�
� Smoke Detector
v
� Heat Detector
❑ EXISTINCs
Pull Station FELLOUJSHIP
AREA
� 3��� �
Horn/Strobe
� Strobe only
Blue Nurnbers =Zone# �sco
��
�iioc�
EXISTING
SANCTUARY
� 1� •
� 110 CD
4O1
� � /
International Ministerial Fellowship
2477 Shadywood Road
Navarre, MN 55392
Date: 6/24/10 Basement Level - Fire System Plan
UNEXCAVATED
KEY Scale: 1/16" = 1'-0"
• Smoke Detector
v
• Heat Detector
� Horn/Strobe
UNEXGAVATED
� Fire/Burg Alarm Control Panel
Blue Numbers = Zone#
>>
� �
10 CD
�
EXISTINCs�.
STORACsE
�
'V�Y 1�Y
�
� �