2016-00602 - alarm system - Laserfiche WebLink

Home Browse Search

dn-6724:b1 FCM-1 (A) & FRM-1 (A) Series NOTIFIER Control and Relay Modules by Honeywell Intelligent/Addressable Devices General FCM-1(A)Control Module: The FCM-1(A)Addressable Con- trol Module provides Notifier intelligent fire alarm control pan- els a circuit for Notification Appliances (horns, strobes, speakers, etc.)Addressability allows the FCM-1(A)to be acti- lif vated, either manually or through panel programming, on a select(zone or area of coverage)basis. Aave FRM-1(A)Relay Module: The FRM-1(A) Addressable Relay Module provides the system with a dry-contact output for acti- vating a variety of auxiliary devices, such as fans, dampers, „ ' control equipment,etc.Addressability allows the dry contact to *4 be activated, either manually or through panel programming, ', on a select basis. frt,, tleFlashScan®(U.S. Patent 5,539,389) is a communication pro- • rAig tocol developed by NOTIFIER Engineering that greatly , enhances the speed of communication between analog intelli- gent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new infor- mation,the panel CPU stops the group poll and concentrates on single points.The net effect is response speed greater than five times that of other designs. FCM-1(A) Features • Built-in type identification automatically identifies these • The FCM-1(A)is configured for a single Class B(Style Y)or devices to the control panel. Class A(Style Z)Notification Appliance Circuit. • Internal circuitry and relay powered directly by two-wire • The FRM-1(A) provides two Form-C dry contacts that SLC loop.The FCM-1(A)module requires power(for horns, switch together. strobes,etc.),or audio(for speakers). • Integral LED "blinks" green each time a communication is Operation received from the control panel and turns on in steady red Each FCM-1(A)or FRM-1(A)uses one of 159 possible module when activated. addresses on a SLC loop (99 on CLIP loops). It responds to • LED blink may be deselected globally(affects all devices). regular polls from the control panel and reports its type and • High noise immunity(EMF/RFI). status, including the open/normal/short status of its Notifica- tionThe FCM-1(A) be used to switch 24 volt NAC power, Appliance Circuit (NAC). The LED blinks with each poll • audioeCM(up 1 70.7) mayVrbe received. On command, it activates its internal relay. The FCM-1(A) supervises Class B (Style Y) or Class A (Style Z) • Wide viewing angle of LED. notification or control circuits. • SEMS screws with clamping plates for wiring ease. Upon code command from the panel, the FCM-1(A) will dis- • Direct-dial entry of address 01— 159 for FlashScan loops, connect the supervision and connect the external power sup- 01 —99 for CLIP mode loops. ply in the proper polarity across the load device. The • Speaker, and audible/visual applications may be wired for disconnection of the supervision provides a positive indication Class B or A(Style Y or Z). to the panel that the control relay actually turned ON. The external power supply is always relay isolated from the corn- Applications munication loop so that a trouble condition on the external power supply will never interfere with the rest of the system. The FCM-1(A)is used to switch 24 VDC audible/visual power, Rotary switches set a unique address for each module. The high-level audio(speakers), or control telephone devices.The address may be set before or after mounting. The built-in FRM-1(A) may be programmed to operate dry contacts for TYPE CODE(not settable)will identify the module to the con- applications such as door holders or Air Handling Unit shut- trol panel, so as to differentiate between a module and a sen- down,and to reset four-wire smoke detector power. sor address. NOTE: Refer to the SLC Manual(PN 51253)for details regarding releasing applications with the FCM-1(A). Refer to the FCM-I-REL Specifications for FCM-1(A) datasheet(DN-60390)for new FlashScan0 releasing applications. Normal operating voltage: 15 to 32 VDC. Construction Maximum current draw: 6.5 mA(LED on). • The face plate is made of off-white heat-resistant plastic. Average operating current: 350 pA direct poll,375 pA group • Controls include two rotary switches for direct-dial entry of poll with LED flashing, 485 pA Max. (LED flashing, NAC address(01-159). shorted.) dn-6724:b1•08/04/09—Page 1 of 2