Laserfiche WebLink
� Positioning, Leveling, and 3��MIN.(76mm) <br /> ' Securing the Fireplace <br /> T'he diagram below shows how to properly position, level, p B <br /> and secure the fireplace. <br /> O A <br /> WARNING: <br /> � To ensure proper clearances <br /> the front framing header <br /> must be installed on its <br /> narrow edge and to the E <br /> front of the frame. � <br /> �' C <br /> 1/2"AAIN.(13mm) <br /> INODEL VENT A B C D E <br /> . SL-750TRS-IPt-D Top 42 1&-1/4 31-7l8 45 63-3/4 <br /> F Reank 42 16-1/4 36-5/8 52 73-1/4 <br /> S1-550TRS-tPI-D T 37 16-1/4 29-3/8 41-1/2 583/4 <br /> Rear* 37 16-1/4 34-1/B 48-1/2 B&1/4 <br /> SL-350TRS-C Top 34 1&1/4 2�-718 39-3I8 55-5I8 <br /> ! Rear* 34 16-1/4 32-5/8 46-3/8 65-1/8 <br /> , <br /> � <br /> .��� "'NOTE tf venting with{2)90°elbows off rear of unit <br /> the dimensions C, D, and E,will change. <br /> Figure 32. Proper Positioning. le�eling, and Figure 4. Fireplace Dimensions, Locations, <br /> Securing o# a FireQtace and Space Requirements <br /> • Place the fireplace �^t:, x�^>�� Minimum Clearances <br /> • Level the fireplace fror^ s�� :� s�e �n� fram front to from the Fireplace to Combustible Materials <br /> back. In es mm <br /> • Shim the fireplacs �.ia� �o�-cti��ust�ble material, such Glass Front .......................................36 ....914 <br /> as sheet metal. as neccssa�� Floor..................................................0 ...... 0 <br /> Rear ................................................ 1/2.....13 <br /> • Secure the fireplace to�e fram�n�g us�ng nails or screws Sides ............................................... 1/2.....13 <br /> through the nailing tabs. *Top (SL 750TRS-IPI-D).....................3 1/4 ...83 <br /> (SL-550TRS-IPI-D, SL-350TRS-C)..... 1 1/2 ...38 <br /> Ceiling.*............................................31 ....787 <br /> . <br /> * The clearance to the ceiling is measured from the top <br /> of the unit, excluding the standoffs (see Figure 37). <br /> _ -- - -- Minimum Clearances <br /> _ _ _ _ _ <br /> from the Vent Pipe to Combustible Materials <br /> . Locating the Fireplace <br /> �aace and clearance requirements for locating a fireplace Inches m�n <br /> Vertical Sections. ............ 1 ............... 25 <br /> �°~.hin a room (see Figure 4). <br /> Horizontal Sections <br /> Clearance Requirements Top.................................. 3 ............... 75 <br /> -��to and back of the fire lace are defined b stand-offs. Bottom............................. 1 ............... 25 <br /> P P Y Sides ............................... 1 ............._.25 <br /> -^e minimum clearance to a perpendicular wall extending <br /> :.asT the face of the firepface is 3 inches (76mm). The back At Wa/I Firestops <br /> �� t#�e fireplace may be recessed 16 1/4 inches (413mm) Top................................2 1/2............63.7 <br /> �-To combustible construction. Bottom............................ 1/2.............. 13 <br /> Sides ................._............. 1 ............... 25 <br /> i �^e distance from the unit to combustible construction is to <br /> �- measured from the unit outer wrap surface to the com- For minimum clearances, see the direct vent termination <br /> ' :=..stible construction, NOT from the screw heads that se- clearance diagrams in Figures 29 and 30 in this manual. <br /> _; ,:.,re the unit together. <br /> 17 <br />