2017-00073 - new structure - Laserfiche WebLink

Home Browse Search

r GENERAL NOTE3: 1. Wall thicknesses noted are nominal unless specifically stated otherwise. 2. Maximum wall to footing centerline offset is 2". A minimum of 2"of footing is to extend on each side of the wall. 3. Bar laps when required are to be at least 40 bar diameters for grade 40 and 60 bar diameters for grade 60. 4. Bend horizontal bars or provide matching hooks around all wall corners and intersections. 5. Horizontal bars may be placed anywhere within the wall thickness provided 2"minimum cover is provided. 6. Allowable bar placement tolerance is 112". Tying is not required if tolerances are met and maintained. 7. Dowels may be drilled and installed after footing pour unless otherwise noted. Vertical bars may be embedded into footing in place of dowels at the same embedment. Vertical bars and dowels do not need to align. Dowels may be bent down for safety and covering then bent back before wall placement. 8. Sill plate sections require at least two anchors with one within 4"to 12"of each end and at all corners and intersections. Walls less than 24"in length require only one anchor. Sill plates may overhang the face of the wall provided the overhang is not loaded vertically and all anchor bolUconnection tolerances are met. 9. Anchor bolts 112"or larger in diameter do not require corrosion protection per IRC section R317.3.1 exception 1. 10. Anchor bolts may be substituted with 1/2"diameter threaded rod epoxy grouted at same spacing with 7"embed. 11. The presence of form oil on the reinforcing is acceptable for the conditions contained in these drawings. 12. Slope grade 6"minimum downward away from foundations within first 10 feet or provide Code adequate swale. 13. Do not backfill until the concrete has reached at least 70 percent of the 28 day concrete strength. Use of adequate shoring is required when the final floor and slab systems are not in place and fully anchored. 14. Maximum inside window well dimension is 72". Well walls are to be at least 8"thick placed monolithically with house walls with horizontal bars extended into them and around corners. Provide two additional vertical bars and one additional anchor bolt each side of opening. Opening header by others. COLD WEATHER GUIDELINE3: The following information is general guidelines for the placement of concrete in cold weather conditions. It is the contractor's responsibility to ensure proper means and methods are followed and that the final in place product is adequate. 1. The contractor is to work with the concrete supplier to obtain a mix design which accounts for the conditions expected. Use of extra cement,early-strength concrete,and accelerators are recommended at temperatures below 20 degrees F. 2. Concrete is to be delivered to the site in a timely manner. 3. Placement of concrete earlier in the day to take advantage of latent heat of sunlight is advised. 4. Do not add additional water. Using water-reducing admixtures is recommended when required. 5. Forms are to be free of snow and ice. Do not place concrete in contact with frozen ground,snow,or ice. 6. Preheating of rebar is not required,however it is to be free of frost,snow,and ice. 7. Use of form blankets or other approved protection is highly recommended for the top of the wall at temperatures below 10 degrees F and for the whole wall when below zero degrees F. Oswell Englneering and Consulting,L.L.C. 1901 E Hennepin Ave,#201 ."x;��' �-'•��`-f�- Project Name: 2017 Standardized Concrete Foundation Drawings Mlnneapolis�MN b5413 �� Description: General Notes Phone:812-720-4639 �-? ',,�. Project# 16.100 Fax:812-886-2968 ' jt Client Name: Abfalter Brothers Concrete LLC www.oswellec.com . � Client Address: 15546 Cleveland Street, Elk River,MN 55330 Page S2 of S6 ` '�` .��.=:. 1 11/2017