2014-01148 - alarm system - Laserfiche WebLink

Home Browse Search

� `� ( • t . I � ' � t ' The 4010ES is comparible with an extensive list of remote Status is deternvned by comparing the current sensor peripheral devices including printers,PC Annunciators and value to its average value.Tracking this average value as both conventional and addressable devices including a continuously shifting reference point filters out . TrueAlarm analog sensors. environmental factors that cause shifts in sensitivity. . . . - , . . � - . . Programmable sensitivity of each sensor can be selected at the control panel for different levels of smoke Overview.The 4010ES provides standard addressable obscuration(shown directly in percent)or for specific device communications for IDNet compatible devices. heat detection levels.To evaluate whether the sensitivity Using a two wire communicarions circuit,individual shouid be revised,the peak value is stored in memory and devices such as manual fire alarm stations,TrueAlann can be easily read and compazed to the alarm threshold sensors,conventional IDC zones,and sprinkler waterflow directly in percent. switches can be interfaced to the addressable controtler to coinmunicate their identity and stalus. CO sensor bases combine an electrolytic CO sensing Addtessability allows the location and condition of the module with a TrueAlann analog sensor to provide a connected device to be displayed on the operator interface single multiple sensing assembly using one system LCD and on remote system annunciators.Additionally, address.The CO sensor can be enabled/disabled,used in control circuits(fans,dampers,etc.)may be individually LED/Switch modes and custom controi,and can be made controlled and monitored with addressable devices. public for communication across a fire alarm Network. (refer to data sheet S4098-0052 for details) Addressable Operation.Each addressable device on the communication channel is continuously interrogated TrueAlarm heat sensors can be selected for fixed for status condirion such as:norn�a.l,off-normal,alartn, temperature detection,with or without rate-of-rise supervisory,or troubie.Both Ciass B and Class A detecrion.Urility temperature sensing is also available, pathway operation aze available. Sophisticated poll and typically to provide freeze warnings or alert to HVAC response communication techniques ensure supervision system problems.Readings can be selected as either integrity and allow for"T-tapping"of the circuit for Fahrenl�eit or Celsius. Ciass B operation.Devices with LEDs pulse the LED to TrueSense Early Fire Detection. Multi-sensor indicate receipt of a communications poll and can be 4098-9754 provides photoelectric and heat sensor da#a tumed on steady from the panel. using a single 40I OES IDNet address.The panel evaluates � IDNet+Channel Capacity.T'he Main System Supply smoke activity,heat activity,and their combination,to provides an IDNet+signaling line circuit(SLC)that provide TrueSense early detection.For more deta.ils on supports up to 248 addressable monitor and control this operation,refer to data sheet 54098-0024. . devices intermixed on the same pair of wires. � , � � , � � _ � _ � _ lDNet+ Communications wiring specifications. . IDNet+circuits may be run on NEC 760 untwisted pair, Sensor Status.TrueAlarm operation allows the control twisted pair,or shielded twisted pair conductors. panel to automatically indicate when a sensor is almost dirty,dirty,and excessively dirty.The NFPA 72 IDNet+Wiring Specificatio�s requirement for a test of the sensitivity range of the Size 18 AWG(o.82 mmz) sensors is fulfilled by the ability of TrueAlarm operation T� NEC 760 Wire(untwisted,twisted, to maintain the sensitivity level of each sensor.CO or shielded twisted pair) Sensors track their 10 year active life status providing Farthest Distance �26-24g Up to 2500 feet(762 m) indicators to assist with service planning.Indicators occur from Control Panei at: 1 yeaz,6 months,and when end of life is reached. per Device load up to 125 Up to 4000 ft(1219 m) Modular TrueAlarm sensors use the same base and Up to 12,5Q0 ft(3.8 km) �fferent sensor types(smoke or heat sensor)and can be Tota{Wire Ler�th Allowed Class Note:The sum of line-to-line �ily interchanged to meet specific location requirements. A or Class B,induding'T-taps° capacitance plus t�e capaatan� for Class B wiring(total for both of either fine-to-shield(if shieid is This allows intentional sensor substitution during building isolated arcuits combined) present)=0.6 pF inaximum.(total consiruction when conditions are temporarily dusty. for both isolated arcuits combin�) Instead of covering smoke sensors(causing them to be 'Other dreuits may require shielded wiring.Review your system with disabled),heat sensors may be installed without your local Simplex product supplier. reprogramming the control panel.The control panel will indicate an inconect sensor type,but the heat sensor will - • s • - . . operate at a default sensitivity w provide heat detection for building protection at that location. Addressabte device communications include operation of TrueAlarm smoke and temperature sensors. Smoke sensors transmit an output value based on their smoke chamber condition and the CPU maintains a current - value,peak value,and an average value far each sensor. 4 S4010-0004-9 5/2014 -