Laserfiche WebLink
� "Pechnical Ev�luation Re�ort('PER) <br /> 3.3. Use of Thermasheath�-3, rhermasheath�-XP, TSX-8500, TSX-8510 and TSX-5520 in structures where the <br /> exterior wall covering is unable to resist 100%of the transverse wind load is outside the scope of this Technica) <br /> Evaluation Report(TER). <br /> 3.4. Any code compfiance issues noti specifically addressed in this section are outside the scope of this evaluation. <br /> �8. Procfuct Description anci Wiaterials: <br /> 4.1. Thermasheath°-3, Thermash�ath�-XP, TSX-8500, TSX-8510 and TSX-8520 are non-structural foam plastic <br /> insulating sheathing (FPIS) panels consisting of a closed-cefl rigid polyisocyanurate(polyiso)foam core <br /> bonded to various facers (ASTIVI C1289 Type 1, Class 1). <br /> r.� <br /> J' 4 ' <br /> F Y�� -' <br /> .,t ' �� <br /> •T ����a. ' .. ��y� •_'�. <br /> � Yl�yy .�.1.'�d.�A,,,.n�•T^ ¢��'����''""Y.�7�' �� <br /> �:;a , <br /> .,�.R"`�o;,�`��4r•�=' <br /> Figure 1a:Thermasheath�-3 Figure 1b:7SX-8500 Figure ic:TSX-8510 <br /> 4.1.9. Thermasheath�-3 consists of a polyiso core bonded to Kraft reinforced aluminum facers on each side. <br /> Both sides have a reflective surface. <br /> 4.1.2. Thermasheath�-XP consists of a polyiso core bonded to aluminum facers on each side. Both sides may <br /> be left exposed; one side has a white modified acrylic coating,and the other side has a reflective surface <br /> with a clear coating. <br /> 4.1.3. TSX-8500 consists of a polyiso core bonded to glass fiber reinforced aluminum facers on each side. Both <br /> sides have a reflective surface. Each board is marked on the non-exposed side. <br /> 4.1.4. TSX-8510 consists of a polyiso core bonded to glass fiber reinforced aluminum facers on each side. The <br /> exposed side has a white modified acrylic coating. The non-exposed side has a reflective surface. (This <br /> product is identical to TSX-8500 except for the white coating on the exposed side.) <br /> 4.1.5. TSX-8520 consists of a polyiso core bonded to glass fiber reinforced aluminum facers on both sides. Both <br /> sides may be exposed; one side has a white modified acrylic coating, and the other side has a reflective <br /> surface. <br /> 4.2. Materia!Availability <br /> 4.2.1. Thickness: '/2"(12.7 mm)through 4.5"(114.3 mm) �,� <br /> 4.2.2. Standard width: 48"(1219 mm) <br /> 4.2.3. Standard length: 96", 108"and 920"(2438 mm,2743 mm and 3048 mm) <br /> 5. Applications: <br /> 5.1. Thermallnsulation <br /> 5.1.1. Thermasheath�-3, Thermasheath�-XP, TSX-8500,TSX-8510 and TSX-8520 are non-structural FPIS <br /> panels used as thermal insulation within the building envelope, including, but not limited to, attic, <br /> crawlspace,wali, roof,ceiling,floor and foundation assemblies. <br /> 5.1.2. Thermasheath�-3, Thermasheath�-XP,TSX-8500,TSX-8510 and TSX-8520 may be installed horizontally <br /> under foundations and vertically on the interior side of footings and foundation walls. <br /> 5.1.3. Thermasheath�-3,Thermasheath�-XP,TSX-8500, TSX-8510 and TSX-8520 meet the continuous <br /> insulating sheathing requirements complying with the provisions of lECC Section 40?.. <br /> TER No. 1309-03 Page 3 of 11 <br /> Rmax Therrnasheath�'-3,Thermasheath�-XP, <br /> TSX-8500, TSX-8510&TSX-8520 <br />