01-13-2003 Council Packet - Laserfiche WebLink

Home Browse Search

Of^arallon lor each channel: ^ Channel/input 1, Style B (Class B) two-wire smoke de- Jector Input and Channel/input 3, Style B (Class B) or Style D (Class A) two-wire smoke detector or waterflow input. • Channel/Input 2 and Channel/Input 4 Style B (Class B) contact closure input. • Refer to Device Compatibility Document for listed com patible devices. Notification Appliance Circuit (TB4 Terminals If+l and 2H): • Style Y (Class B) circuit. • Power-limited and supervised (monitored for opens, shorts, and earth fault). • Operating voltage nominal 13.8 VDC. • Current for all external devices: 1.0 amp. • End-oMlne resistor: 2.2K ohms. 1/2 watt (P/N 27070). • Refer to Device Compatibility Document for listed com patible devices. Two Optional Form-C Relays (TB1 Terminals 1 through 6): Operating voltage: nominal 12 VDC. Contact rating: 2.0 amps 9 30 VDC (resistive), or 0.5 amps O 30 VAC. 12 VDC Resettable Power (TB4 Terminals 3(4] and 4[-]): • Operating voltage; nominal 12 volts. • Up to 200 mA available to power four-wire smoke detec tors. • Power-limited and supervised circuitry. • Recommended maximum standby current: 60 mA. NOTE: 1) For power supply and battery calculations, refer to the 411UDAC manual. OPERATING POWER: Primary Power Source (AC): AC power connections are made inside the 411 UDAC cabi net. The primary power source is 120 VAC, 60 Hz. 0.3 amps. Secondary Power Source (Batteries): One 12-voll bat tery can provide power for up to 7 A.H. applications. Two 12-voll, 7 A.H batteries (In parallel) can provide power for up to 14 A.H. applications (60 hour standby). The battery charger is current-limited and capable of recharging sealed leac-acid-type batlenes. The charger shuts off when the system is in alarm. Refer to the battery calculations table in the 411 UDAC manual to determine the correct battery ratng. TRANSFORMER ASSEMBLY: One transformer is shipped in the same carton as the cabinet and main circuit board but not mounted in the cabinet. The transformer should be installed before the cabinet is mounted to the wall. AUXILIARY RELAY: Two optional Form-C relays (411RK) are available for installation on the 411 UDAC main circuit board. The relays are programmable for activation on fire alarm, host panel trouble, fire supervisory, process monitoring, total ccmmumcations failure, and DACT trouble. Relay contact rating: 2.0 amps ^ 30 VDC (resistive); or 0.5 amps d 30 VAC ^resistive). PRODUCT LINE INFORMATION Model 411 UDAC Description Fou--channel. dual-line, stand-alone or slave Fire Alarm Communicator. Includes housing, operating and programming instructions. Use PRO-411 (below) hand-held DACT program mer for local programming; or PK-411UD (be- tow) Windows-based programming software for remote programming and real-time diag nostics. DP-2 Dead-front dress panel, required for Cana dian applications, PRO-411 Optional hand-held DACT programmer which can be used to troubleshoot and program the 411 UDAC. as well as access the various modes of operation. PK-411 UD Remote upload/download. Windows 95 com patible, programming software kit (3.5* disk and PK-411UD Program Manual). The PK- 411UD enables a user to program the 411 UDAC off-site via the public switched tele phone network using any personal computer with Wiridov^rs 3.1 or greater or Windows 95 and a 1200-baud Hayes0-compatible mo dem. 411RK MCBL-7 PS-1270 Optional dry auxiliary Form-C relays, with contacts rated for 2.0 amps G 30 VDC (re sistive) or 0.5 amps Q 30 VAC (resistive). Optional use requires two relays, DACT phone cord, seven feet long (two re quired). Battery, 12-volt. 7.0 AH (one required for 24- hour systems: two [wired in parallel] required tor 60-hour systems). See page 4 for COMPATIBLE UL-LISTED RECEIVERS OP-51S52 — Pig«3oi4 -.1