Laserfiche WebLink
Job Truss Truss Type Qty Ply 421056 S.B. Hopkins-Danberry/Coehen <br /> MASTER FAL Floor Supported Gable 1 1 <br /> Job Reference(optional) <br /> Littfin Truss Company,Winsted,MN,Jim Boruff 7.630 s Jul 9 2015 MiTek Industries,Inc. Thu Dec 03 08:01:52 2015 Page 1 <br /> ID:_Y2ihMJyJBLhLorGn3OSCDyD?KF-oi?B IsuOgmgnnngDfJFIBvfL4Zf8FKyghJT83XyCkUj <br /> 0Na 011c8 <br /> Scale=1:26.4 <br /> 1.5x3= 3x6 FP= 1.5x3= <br /> 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 <br /> o '''t <br /> a er ar a ar T1 er a GI; or er o, ar T2Q or e, o <br /> 4 4 4, P ,It ? 4 $ 4 4 Q $ IM <br /> en <br /> 0 35 ST1 ST1 ST1 ST1 ST1 ST1 ST1 ST1 ST1 ST1 T1 ST1 ST1 S111 36 0 <br /> 7. <br /> # # R1 # # # # # R2 # # <br /> 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 <br /> 3x4= 3x6 FP= 3x4= <br /> 20-3-0 <br /> 20-3-0 <br /> Plate Offsets(X,Y)— [1:Edge,0-0-12] <br /> -- <br /> LOADING(psf) SPACING- 2-0-0 CSI. DEFL. in (loc) 1/deft L/d PLATES GRIP <br /> TCLL 40.0 Plate Grip DOL 1.00 TC 0.05 Vert(LL) n/a - n/a 999 MT20 197/144 <br /> TCDL 10.0 Lumber DOL 1.00 BC 0.01 Vert(TL) n/a - n/a 999 <br /> BCLL 0.0 Rep Stress Incr YES WB 0.04 Horz(TL) 0.00 18 n/a n/a <br /> BCDL 5.0 Code MNSRC2015ITPI2007 (Matrix) Weight:80 lb FT=20%F,11%E <br /> LUMBER- BRACING- <br /> TOP CHORD 2x4 DF 1800F 1.6E(flat) TOP CHORD Structural wood sheathing directly applied or 6-0-0 oc purlins, except end verticals. <br /> BOT CHORD 2x4 DF 1800F 1.6E(flat) BOT CHORD Rigid ceiling directly applied or 10-0-0 oc bracing. <br /> WEBS 2x4 DF 1800F 1.6E(flat)*Except* <br /> BL1:2x4 DF Std or 2x4 SPF Stud(flat) <br /> OTHERS 2x4 DF Std or 2x4 SPF Stud(flat) <br /> REACTIONS. All bearings 20-3-0. <br /> (Ib)- Max Gray All reactions 250 lb or less at joint(s)34,18,33,32,31,30,29,28,27,25,24,23,22,21,20. 19 <br /> FORCES. (Ib)-Max.Comp./Max.Ten.-All forces 250(Ib)or less except when shown. <br /> NOTES- (7-8) <br /> 1)All plates are 1.5x4 MT20 unless otherwise indicated. <br /> 2)Gable requires continuous bottom chord bearing. <br /> 3)Truss to be fully sheathed from one face or securely braced against lateral movement(i.e.diagonal web). <br /> 4)Gable studs spaced at 1-4-0 oc. <br /> 5)"Semi-rigid pitchbreaks including heels"Member end fixity model was used in the analysis and design of this truss. <br /> 6)Recommend 2x6 strongbacks,on edge,spaced at 10-0-0 oc and fastened to each truss with 3-10d(0.131"X 3")nails. Strongbacks to be attached to walls at their outer ends or restrained <br /> by other means. <br /> 7)This truss must not be exposed to environments that are corrosive or greater than 19 percent moisture,and moisture of lumber not to exceed 19 percent <br /> 8)It is the responsibility of the engineer of record to determine the suitability of this component for this project per ANSI/TPI 1,Section 2. <br /> LOAD CASE(S) Standard <br /> JTTFHN <br />