Laserfiche WebLink
L-1 LAVATORY <br /> ES-LFUSG-B-M2 <br /> For Residential and Commercial Applications <br /> Job Name Contractor <br /> Job Location Approval <br /> Engineer Contractor's P.O. No, <br /> Approval Representative <br /> LEAD FREE+ <br /> Series LFUSG-Br4 <br /> Under Sink Guardian® :i•. . . <br /> The LFUSG-B-M2 Under Sink Guardian' ti"(10mm)tem '- ,��� •` � . ,. x ., <br /> pression and Quick-Connect fitting thermostatic mixing valves <br /> maintain and limit hot water to desired selectable temperature <br /> between 80°F and 120'F(27°C and 49°C)with flow rates as low * i r" <br /> as 0.25 gpm(1.0 Ipm)and as high as 2.25 gpm(8.5 Ipm),The ,;.y,,r <br /> mixing valve is listed to ASSE Standard 1070 for single fixture <br /> applications and IAPMO IUPC.The LFUSG-B-M2 features Lead , ;" e <br /> Free'construction to comply with Lead Free'installation require- t 41:: <br /> mems.The superior flow characteristics of these valves provide <br /> temperature control with low pressure drop.As an added fea- <br /> ture,the LFUSG-B-M2 incorporates dual check valves to protect CFUSG-B-MD LFUSG-B-OC-M2 <br /> against cross-flow and integral screens to filter out debris. ASSE 1070&IAPMO cUPC Listed <br /> Features <br /> • Lead Free'Brass body construction <br /> • Installs easily between the stop valves and faucet Mat en s <br /> Body: Lead Free'Brass <br /> • Includes tamper resistant locking nut to prevent accidental mis- <br /> adjustment Rubber Disc: Bursa-N <br /> • Built-in check valves prevent migration of hot water to cold and 0-rings: Buna-N <br /> cold water to hot water piping Spring: Stainless steel <br /> • Provided with cap for three port application Piston: Noryl5 <br /> • Integral strainer with 40 mesh stainless steel screens to litter Thermostat: Copper <br /> out debris <br /> Approval <br /> Applications <br /> uP� <br /> The unit Is intended for under sink installation to control the hot c er <br /> water temperature and minimize the occurrence of accidental ASSE 1070 <br /> scalding.The water temperature must be adjusted by the install- <br /> er using a thermometer to measure the hot water temperature Pressure-Temperature <br /> at the faucet outlet. Maximum temperature of 105'F(41°C)is Minimum supply pressure:30psi(207 kPa) <br /> recommended. <br /> Specifications Hot inlet temperature: 120°F-180°F(49"C-82°C) <br /> A Thermostatic Mixing Valve shall be installed on the hot water Cold inlet temperature:39'F-80°F(3.8`C-27°C) <br /> supply to the fixture.The valve shall be ASSE Standard 1070 and Minimum inlet temperature differential:5°F(2.8°C) <br /> IAPMO cUPC listed and contra the temperature Of the hot water. Temperature range:80"F-120`F(27`C-49"C) <br /> It shall have a Lead Free'brass 4-port,"H"pattern body. Lead <br /> Free-under counter thermostatic valves shall comply with state Maximum pressure: 150psi(10,3 bar) <br /> codes and standards,where applicable, requiring reduced lead Minimum Flow:0.25 gpm(1.0 Vm) <br /> content.The valve shall include integral check valves,integral <br /> screens and an adjustment nut with locking feature.The valve <br /> shall be provided with ele(lOmm)male compression or aids- 'The wetted surface of this product contacted by consumable water <br /> connect fittings.The valve shall be Watts Series LFUSG-B. contains less than one quarter of one percent(0.25%) <br /> For satin chrome finish specify-SC. of lead by weight. <br /> Noryr is a registered trademark of SABIC Innovative Plastics. <br /> Watts product W n in U.S cusry units and metricpare approximate and are prowled for re an;For omeasurements, Apinaee corbel Was Technical Sevor.Waitsrisevs the ntst b change a modify marl design,Wns5uc�n spcUe/Uons or materials <br /> II� <br /> with- <br /> out prior name and maw arming arty obligation to make web fllariges and int ifcalores on Watts products prenasly ce:artiscyuarF aril <br /> Page:21/51 <br />