Laserfiche WebLink
4. MOUND SIZING <br /> A. Calculate Clean Sand Lift: 3 feet minus Depth to Limiting Condition (1.C) = Clean Sand Lift (1 ft minimum) <br /> 3.0 ft - 2.0 ft = 1.0 ft Design Sand Lift (optional): <br /> B. Calculate Upslope Height: Clean Sand Lift (4.A) +media depth (1 ft.) +cover (1 ft.) = Upslope Height <br /> 1.0 ft + 1.0 ft + 1.0 ft= 3.0 ft <br /> 0-34:',tope Multiplier Table <br /> Land Slope% 0 t 2 3 4 5 6 7 8 9 10 11 12 13 14 15 t6 17 18 19 20 21 22 23 24 25 <br /> Upslope 3:1 3.00 2.91 2.83 2.75 2.68 2.61 2.54 2.48 2.42 2.36 2.31 2.26 2.21 2.17 2.13 2.09 2.06 2.03 2.00 1_97 1.95 1.93 1.91 1.89 1.87 1.85 <br /> Beln1 Ratio 4:1 4.00 3.85 3.70 3.57 3.45 3.33 3.23 3.12 3.03 2.94 2.86 2.78 2.70 2.62 2.55 2.48 2.41 2.35 2.29 2.23 2.18 2.13 2.08 2.03 1.98 1.93 <br /> Land Slope% 0 t 2 3 4 5 6 7 8 9 IO 11 12 t3 14 15 16 17 1 18 19 20 21 22 23 24 25 <br /> Downslope 3:1 3.00 3.09 3.19 3.30 33.41 3.53 3.66 3.80 3.95 4.11 4.29 4.48 4.69 4.95 5.24 5.55 5.88 6.24 6.63 7.04 7.47 7.93 8.42 8.93 9.46 10.02 <br /> Berns Ratio 4:1 4.00 4.17 4.35 4.54 4.76 5.0015.26 5.56 5.88 6.25 6.67 7.14 7.6918.29 8.92 9.57 10.24 10.94 11.67 12.42 13.19 13.93 14.82 15.67 16.54 17.44 <br /> C Select Upslope Berm Multiplier <br /> (based on land slope): 3.57 (figure D-34) <br /> D. Calculate Upslope Berm Width: Multiplier (4.C)X Upslope Mound Height (4.B) = Upslope Berm Width <br /> 3.57 ft x 3.0 ft = 10.7 ft <br /> E. Calculate Drop in Elevation Under Bed: Bed Width (2.B) X Land Slope (1.D) : 100=Drop (ft) <br /> 10.0 ft X 3.0 % : 100= 0.30 ft <br /> F. Calculate Downslope Mound Height: Upslope Height (4.B) +Drop in Elevation (4.E) =Downslope Height <br /> 3.0 ft + 0.30 ft = 3.3 ft <br /> G Select Downslope Berm Multiplier <br /> (based on land slope): 4.54 (figure D-34) <br /> H. Calculate Downslope Berm Width:Multiplier (4.G)X Downslope Height (4.F)=Downslope Berm Width <br /> 4.54 x 3.3 ft = 15.0 ft <br /> I. Calculate Minimum Berm to Cover Absorption Area:Downslope Absorption Width (3.B or 3.C) +4 ft. =ft <br /> 10.0 ft + 4 ft = 14.0 ft <br /> J. Design Downslope Berm =greater of 4H and 41: 15.0 ft <br /> K. Select Endslope Berm Multiplier: 3.00 (usually 3.0 or 4.0) <br /> L. Calculate Endslope Berm (4.K)X Downslope Mound Height (4.F) =Endslope Berm Width <br /> 3.00 ft X 3.3 ft = 9.9 ft <br /> M. Calculate Mound Width: Upslope Berm Width(4.D) +Bed Width (2.B) +Downslope Berm Width (4.J) =ft <br /> 10.7 ft + 10.0 ft + 15.0 ft = 35.7 ft <br /> N. Calculate Mound Length: Endslope Berm Width (4.L) +Bed Length (2.C) +Endslope Berm Width (4.L) =ft <br /> 9.9 ft + 63.0 ft + 9.9 ft = 82.8 ft <br /> 0. If using a registered product, enter the Component Length: in. : 12 ft. <br /> P. If using a registered product, enter the Component Width: in. : 12 ft. <br /> Q. Number of Components per Row =Bed Length (2.C)divided by Component Length (4.0) (Round up) <br /> 63 = <br /> R. Number of Rows =Bed Width (2.B) divided by Component Width (4.P) (Round up) <br /> Adjust Contour Loading Rate on Design Summary page until this number is a whole number <br /> S. Total Number of Components =Number of Components per Row X Number of Rows <br /> X = <br />