2014 - 00968 - pool - in ground - Laserfiche WebLink

Home Browse Search

Drainsafe DS 360 • Anti—Entrapment Type,Submerged Suction Outlet Cover Read these instructions in their entirety prior to starting installation ANSI/ASME A112.19.8(2005)Certified.Safe Flow Rate 123(GPM)Gallons Per Minute For use with suction outlet sumps up to 8 inch in size Note: read all instructions prior to installation.It is recommended this product be used in conjunction with an ANSI/ASME A112.19.17 Certified(SVRS)Safety Vacuum Release System,properly installed by a licensed pool professional. • Important Information: Do not exceed DS 360 Safe Flow Rate:123 gallons per minute. Post safe flow rate in an obvious location in pump room. Acceptable connecting pipe sizes:up to 2.5". Inspect this unit for proper attachment daily,inspect for fractured or damaged parts daily. • Never operate any pool/spa facility if drain cover is damaged,cracked,fractured,loose or missing. Use supplied 316 Grade S/S(12 per kit)security screws to install this anti-entrapment type drain cover. Ensure existing sump screw attachment holes are clean and free of debris prior to attachment. Carefully tighten screws to secure cover.Do not over tighten screws.Damage to the DS 360 could result,causing serious injury or death.If the DS 360 is damaged,do not start pump(s)until a new DS 360 unit is properly reinstalled. After slowly tightening supplied screws,be certain DS 360 cannot be moved side to side,vertically or horizontally to ensure secure attachment.Do not over tighten screws. !!!Read these instructions in their entirety prior to starting installation.Keep these instructions for future reference!!! Attempt this operation in a dry environment Do not install this product on seating or backrest of seating area. Do not place this product within three feet of another suction outlet on the same suction line or mounting plane. If one suction outlet should become blocked,the remaining suction outlets shall be capable of handling the flow of the system. Be certain pgol/spa pump(s)_are secured. Use battery operated drill(if need be),or a"yankee type"manual screw diver to pre-drill holes. Use supplied security tool and S/S 316 grade security screws. Do not increase flow through system by'increasing pump size or horsepower. Do not allow children to sit,play or interact with main drains or suction outlets. Optional tools:awl,1/16 inch drill bit,battery operated drill or a"yankee type"manual screw driver to predrill holes, brush and or dust pan to clean surface area prior to installation. Installation: remove existing main drain cover.Clean area and prep for DS 360 install. 1stall this product in aright side up position.ANSI/ASME A112.19.8(2005)labeling is on the top of the unit.Set DS 360 on sump id align existing screw holes with DS 360 screw ports(5.5 to 7.5 inch bolt centers)this configuration fits most common sump mew patterns.Outer edges must be flush with existing pool/spa linen Do not start pump if the edges of the DS 360 are not flush and ght to the existing liner be it;plaster,exposed aggregate,fiberglass,coated surface or vinyl. rsert the two supplied screws into the existing holes in the sump,(6 sets of screws included to match original OEM screws)hand ihten.(Do not overtighten!) den,using a 1/16 inch drill bit,drill approximately(2)1/4 inch deep holes,at a 90 degree off-set(screw holes pre drilled in DS 360 Iver)into the existing mud ring plastic,as close to the sumps frame as possible. 3e all four(4)screw ports to mount DS 360.Insert the other two matching OEM supplied screws,hand tighten only using the pplied uni-screw security tool. DO NOT OVER TIGHTEN SCREWS,AS THIS MAY DAMAGE THE DS 360 OR THE EXISTING SUMP!! • not install DS 360 if screws are not secured properly.Install the next screw size larger(supplied).It is important all four screw achment openings are utilized.In some cases it may require you to predrill four new screw ports for a secure fit.