Laserfiche WebLink
PROJECT NAME: <br /> SOLID STATE AREA LIGHTING FIXTURE TYPE: <br /> DSAP SERIES - LED <br /> 1 <br /> SPECIFICATIONS0 25' <br /> 635mm <br /> HOUSING <br /> Upper housing is heavy gauge cast aluminum (DSAP25) or <br /> 0.125" thick spun aluminum with reveal (DSAP1). Lower <br /> housing is 0.080" thick spun aluminum with integrated LED <br /> module seat. Lower housing is vented at top and bottom for } <br /> convective cooling of LED module. Top Driver chamber is t) <br /> sealed from LED Module chamber. Trulevel ball coupling 18.5" <br /> mount is welded to housing and facilitates quick leveling 470mm <br /> and installation. ' ‘I . <br /> VLED°OPTICS + <br /> Low copper A356 alloy (<.2%copper) cast aluminum housing. <br /> Integrated clear tempered glass lens sealed with a continuous <br /> silicone gasket protects emitters (LED's) and emitter <br /> Reflector-Prism optics,and seals the module from water intrusion <br /> and environmental contaminants. Module is sealed to meet an 4,481:�rtow- <br /> IP67 rating. Each emitter is optically controlled by a <br /> Reflector-Prism injection molded from H12 acrylic (3 types per <br /> module;one from 0°-50°;one from 50°-65°;one from 65°-72°). <br /> Each Reflector-Prism has indexing pins for aiming and is secured <br /> to an optical plate made of matte black anodized aluminum. DSAP25 <br /> The optical plate locates every Reflector-Prism over an emitter. <br /> Reflector-Prisms are secured to the optical plate with a UV curing <br /> PATENT PENDING <br /> adhesive.The Reflector-Prisms are arrayed to produce IES Type II, <br /> III, IV, and V-SQ distributions. The entire Optical Module is field <br /> rotatable in 90°increments. Both module and drivers are factory <br /> wired using water resistant, insulated cord. 7 <br /> LED DRIVER 20" // <br /> Drivers are UL and cUL recognized mounted on a single plate CO1 508mm <br /> and factory prewired with quick-disconnect plugs. Constant <br /> current driver is electronic and has a power factor of>0.90 and i <br /> a minimum operating temperature of-40°F. Drivers accept an <br /> input of 120-277V, 50/60Hz or 347-480V, 50/60Hz. (0 - 10V i <br /> dimmable driver is standard. Driver has a minimum of 3KV f 1 ',[ . <br /> internal surge protection. Luminaire supplied with 20KV surge 16.5" <br /> mm 1.,J I: <br /> protector for field accessible installation.) 419I1, <br /> LED EMITTERS ` <br /> i. <br /> High output LED's are utilized with drive currents ranging from <br /> 350mA to 1050mA. 70CRI Minimum. LED's are available in I <br /> standard Neutral White(4000K), or optional Cool White (5000K) <br /> or Warm White(3000K).Consult Factory for other LED options. <br /> AMBER LED's <br /> PCA(Phosphor Converted Amber) LED's utilize phosphors to _ 1 <br /> create color output similar to LPS lamps and have a slight - . <br /> output in the blue spectral bandwidth. TRA (True Amber) <br /> LED's utilize material that emits light in the amber spectral <br /> bandwidth only without the use of phosphors. <br /> FINISH DSAP1 <br /> Electrostatically applied TGIC Polyester Powder Coat on PATENT PENDING <br /> substrate prepared with 20 PSI power wash at 140°F.Four step <br /> iron phosphate pretreatment for protection and paint <br /> adhesion.400°F bake for maximum hardness and durability. <br /> Texture finish is standard. <br /> c el LIS MADE IN THE <br /> LISTED LISA 2018334 <br /> 660 west Avenue a Palmed,CA 93551 U.S.ARCHITECTURAL <br /> U.S. Architectural Lighting Phone(661)233-2000 Fox(661)23120010 <br /> vnvw esan9 corn 11111L <br />