Laserfiche WebLink
•I •l w <br /> FireLock <br /> STYLES 009H/009/009V <br /> t <br /> Q 4r21 <br /> • Read and understand all instructions before attempting to <br /> install any Victaulic piping products. ""�� <br /> • Depressurize and drain the piping system before attempting <br /> to install, remove, or adjust any Victaulic piping products. <br /> • Wear safety glasses, hardhat,and foot protection. Gasket Grade <br /> Color Code Mark <br /> Failure to follow these instructions could result in serious <br /> personal injury, improper product installation, and/or property 3. CHECK GASKET:Check the gasket to make sure it is suitable <br /> damage. for the intended service.The color code identifies the gasket <br /> grade. Refer to Victaulic publication 05.01 in the G-100 General <br /> Catalog or the 1-100 Field Installation Handbook for the color <br /> INSTRUCTIONS FOR THE INITIAL INSTALLATION code chart. NOTE: GASKETS FOR 009H COUPLINGS ARE <br /> OF STYLE 009H/009/009V COUPLINGS NOT INTERCHANGEABLE WITH GASKETS FOR 009/009V <br /> COUPLINGS. <br /> IFNOTICE <br /> _. <br /> • Victaulic Style 009H/009/009V Couplings are designed for use <br /> ONLY on wet and dry fire protection systems(temperatures <br /> greater than—40°F/-40°C). For rigid pipe connections in sys- <br /> tems operating below 0°F/-18°C,Victaulic recommends Style <br /> 005 FireLock Rigid Couplings with Grade"L"(silicone)gaskets. <br /> • Victaulic Style 009H/009/009V Couplings are provided with the <br /> Vic-PIusTM gasket system.Additional lubrication is not required <br /> for the initial installation of wet pipe systems that are installed <br /> at or continuously operating above 0°F/-18°C. Refer to Victaulic <br /> publication 05.03 in the G-100 General Catalog for the Vic-Plus <br /> • MSDS sheet. <br /> Supplemental lubrication is required for Vic-Plus gaskets only if <br /> any of the following conditions exist. If any of these conditions <br /> 1. DO NOT DISASSEMBLE THE COUPLING:Style 009H/009/009V exist, apply a thin coat of Victaulic lubricant or silicone lubricant to <br /> Couplings are installation ready.These couplings are designed the sealing lips of the gasket interior only. <br /> so that the installer does not need to remove the bolts and nuts • If the gasket has been exposed to fluids prior to installation <br /> for installation.This design facilitates installation by allowing the • If the surface of the gasket does not have a hazy appearance <br /> installer to directly install the grooved end of pipe/mating compo- • If the gasket is being installed into a dry pipe system <br /> nents into the coupling. <br /> • If the system will be subjected to air tests prior to being filled <br /> 2. CHECK PIPE/MATING COMPONENT ENDS:The outside sur- with water <br /> face of the pipe/mating component, between the groove and • If the gasket was involved in a previous installation <br /> the pipe/mating component end,must be smooth and free from <br /> indentations, projections,and roll marks to ensure a leak-tight • If the gasket sealing surface of the pipe contains raised or <br /> seal.All oil,grease,dirt,and cutting particles must be removed. undercut weld seams, or cracks or voids at the weld seams. <br /> Measurements taken across grooved pipe/mating component ends However, lubricated gaskets may not enhance sealing capabili- <br /> must not exceed the maximum allowable flare diameter. Refer to ties on all adverse pipe conditions. Pipe condition and pipe <br /> current Victaulic specifications for the maximum allowable flare preparation must conform to the requirements listed in product <br /> diameter. installation instructions. <br /> www.victaulic.com <br /> VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.©2009 VICTAULIC COMPANY.ALL RIGHTS RESERVED.PRINTED IN THE USA. Acta L lI1C' <br /> n r , nnn,unnC.mnni, <br />