Fire Suppression System - Laserfiche WebLink

Home Browse Search

Cove'r Plate Finishesi') Table H Standard Finishes Special Application Finishes White Polyester Off White Paint Black Paint Raw Brass Chrome Plated Bright Brass Finished Bronze Black Plated Satin Chrome Stainless Steel Custom Color CIad131 Paint(2) Notes: 1. Paint or any other coating applied over the factory finish will void all approvals and warranties. 2. Custom color paint is semi-gloss,unless specified otherwise. 3. Stainless steel clad cover plates are Type 316 Stainless Steel on the finished side and C102 Copper Allow on the back side.Cover plates are not listed or approved as corrosion resistant.Stainless steel clad cover plates are not available perforated. Installation Dimensions Table J Recommended Min.to Min.to Max. Cover Plate Cover Plate Max.Face Dropped Deflector Cover Hole Diameter Cover Plate Sprinkler Diameter Adjustment of Fitting to Distance below Plate in Ceiling Temperature Model inch inch Ceilingt'� Ceiling p Model inch Rating (mm) (mm) (mm) inch inch (mm) (mm) RFC30 3-5/16 2-5/8 1/2 1-1/2 to 2 1/2 to 1 135°F RFC43 RFC (84) (67) (13) (38 to 51) (13 to 25) (57°C) RFC49 135°F12> RFC58 RFC 3-5/16 2-5/8 3/4 1-1/2 to 2-1/4 1/4 to 1 (57°C) (84) (67) (19) (38 to 57) (6 to 25) or 165°F13> (74°C) Notes: 1. Face of fitting to ceiling dimensions are based on a nominal thread make up.Verify dimensions based on fitting and thread sealing method prior to installation.A 1/2"x 1/2"brass nipple extension(Reliable P/N 6999991900)is available where necessary for replacement of existing sprinklers. 2. For use with 165°F(74°C)temperature rated sprinklers where the Maximum Ceiling Temperature does not exceed 100°F(38°C). 3. For use with 212°F(100°C)temperature rated sprinklers with the Maximum Ceiling Temperature does not exceed 150°F(66°C). Installation Model RFC series sprinklers are intended to be installed in ac- Do not exceed the maximum recommended torque. Exceeding cordance with NFPA 13,NFPA 13R,or NFPA 13D,as well as the the maximum recommended torque may cause leakage or im- requirements of applicable authorities having jurisdiction.Mod- pairment of the sprinkler. Use care when inserting or removing el RFC series sprinklers must not be installed in ceilings with the wrench from the sprinkler to avoid damage to the sprinkler. positive pressure in the space above. Ensure that the 4 slots in the cup are open and unobstructed following installation.Model Install the cover plate by hand by pushing the cover plate into RFC series sprinklers are shipped with a protective cap that the cup and turning the cover in the clockwise direction until it should remain on the sprinkler until installed.The protective cap is tight against the ceiling. should be replaced following installation of the sprinkler and permanently removed only when the cover plate is installed and the sprinkler system is placed in service following construction. Application Model RFC series sprinklers are installed with the Model FC Model RFC series sprinklers are intended for installation where wrench.The use of any other wrench to installed Model RFC se- residential sprinklers are permitted or required by NFPA 13, ries sprinklers is not permitted and may damage the sprinkler. NFPA 13R, and NFPA 13D. The sprinklers are concealed pen- Temporarily remove the protective cap during installation of the dent residential sprinklers. sprinkler.Insert the Model FC wrench over the sprinkler until the wrench engages the body. Do not wrench any other part of the Model RFC 30, RFC43, and RFC49 sprinklers are available in sprinkler/cup assembly. The Model FC wrench is designed to ordinary temperature classification for installation where the be turned with a standard 1/2"square drive.Tighten the sprin- Maximum Ceiling Temperature does not exceed 100°F(38°C). kler into the fitting after applying a PTFE based thread sealant Model RFC58 sprinklers are available in either ordinary or in- to the sprinkler's threads.Recommended installation torque is 8 termediate temperature classification for installation where the to 18 ft/lb(11 to 24 N/m). Maximum Ceiling Temperature does not exceed 100°F (38°C) or 150°F(66°C), respectively. Bulletin 006 Rev.K .t Page 6 of 7 February 2017 Rellabld www.reliablesprinkler.com