|
t,
<br /> RECEIVED
<br /> � �,AR � 1 Z016
<br /> � �AKIaNA ��n oF oRorva � `T��'����
<br /> 1RG Y6N0�aOMPiqlETICX AOOUC7L
<br /> �RODUCT DESCRIPT°ION contents of the bag in a wheel-barrow;
<br /> Akona�Crack-Resistant Surface Bonding bucket, mortar box, or mechanical mixer. �'
<br /> Mix product thoroughly to achieve a stiff, '
<br /> Cement is a specially-formulated, multi- "
<br /> putty-like consistency. Avoid high speed
<br /> use product. It can be used to build and , ' � �� , �. �.��,
<br /> restore retaining walis or block walls, mechanical mixing which can entrap air � .e_ � �_:
<br /> patch large vertical holes where into the mixture. If the product becomes ,;;� , �,;` .
<br /> non-sagging cement is a must, or repair firm before application, re-mix to proper �s�y� ,"/
<br /> consistency. If required, add additional
<br /> deteriorated stucco. Because it contains �'�`" ��..,. , r.,,,,:.J
<br /> special fibers it will not shrink, crack, or `Nater sparingiy, up to a total of 1 Y2 gal. ��� �� , `
<br /> (5.7 L)liquid per 50 Ib. (22.7 kg)powder. •��*—�--��• -�»,�•� r,,.� .��
<br /> sag on a vertical repair. Provides � - _
<br /> additional overall strength vs.
<br /> conventional concrete. Optional: For improved durability,
<br /> strength; and adhesion when applying ,����-Fi�'; �R
<br /> WI�IEN/YYHERE TO USE over previously coated and non-porous
<br /> surfaces it is recommended to use Akona :s-�"�����"
<br /> • Repair deteriorated concrete walis Concrete Bonding Additive in place of
<br /> • Patch deep vertical holes water(sold separately). Concrete Bonding
<br /> . Restore damaged concrete, masonry, Additive may be diluted by up to '/3 with often with water and use a "light touch"
<br /> and stucco water, however, for extra difficult when finishing the surface. Do not over
<br /> • Bonds dry-stacked masonry walls restoration or waterproofing projects, it is trowel. Protect the surface from use until
<br /> recommended to be used at full strength. patch is completely hard and set. Clean
<br /> ADVANTAGES up with soap and warm water as soon as
<br /> • Moisture resistant ApPLICAT[ON application is completed.
<br /> • Glass fiber reinforced for durability Apply only to surfaces that are frost-free
<br /> Bonding Dry-Stack Segmental
<br /> . High strength and above 40°F (4°C) and below 100°F Retaining Walis&Masonry Walls:
<br /> • Controls shrinkage, cracking, and (38°C) within 24 hours of application and
<br /> sagging on vertical repairs 72 hours thereafter. Dampen the wall • Footings or Foundations: The secret
<br /> • Just mix with water or a bonding surface prior to applying product with a to sound structure is a strong, level
<br /> additive and use water spray. If the wall becomes dry foundation. A level and properly aligned
<br /> before application of product, re-wet the footing makes stacking and troweling
<br /> AVAILABLE SIZE wall. The dampened walis are important in much easier. Footings must be built
<br /> • 50 Ib. (22.7 kg)bag (BOM#102614) estabiishing a strong bond. below the frost line and should a be a
<br /> � g� minimum of twice the thickness of the
<br /> �" �'�;: * ' blocks used. Consult your local
<br /> COVERAGE • �'
<br /> �°-�r. masonry supplier for information about
<br /> One 50 Ib. bag covers approximately 50 � e footings and slab construction.
<br /> sq. ft. at'/8 in. (3 mm)thickness �R • Dry-stacking Masonry Units: Lay the
<br /> �- first course of masonry units in a full
<br /> « „ _
<br /> SWRF/PCE PREPARATION � r�* bed of Crack-Resistant Surface
<br /> � '� � ' Bonding Cement. Make sure this course
<br /> Read all directions before starting work. f � � � � is strai ht and level. Dr -stack meson
<br /> Remove all loose or unsound materials. ��""``�� ; > , g y ry
<br /> �-� �`.. '" " ;,;:: units in a staggered or running bond
<br /> Thoroughly clean surface of dirt, dust, pattern for strength. As you place
<br /> grease, paint or other contaminants - masonry units in position, slide it
<br /> before building or restoring walls. against the masonry units below to
<br /> PRE-WET SURFACE JUST PRIOR TO Patching or Filling Holes in Concretel
<br /> APPLICATION OF PRODUCT. Masonry Walls&Stucco Repair: smooth out any roughness. Crack-
<br /> Resistant Surface Bonding Cement can
<br /> Crack-Resistant Surface Bonding Cement be used between masonry units to
<br /> MIXING is ideally suited for patching or filling holes maintain a level and properly aligned
<br /> in concrete or masonry walls, as well as,
<br /> Begin with approximately 1 gal. (3.8 L) of repairing cracks or filling openings in Wall. The better you are in maintaining a
<br /> clean, cool water per bag. Mix complete stucco walls. Apply up to %2 in. (1.3 cm) level and aligned wall, the stronger and
<br /> more attractive your finished wall will
<br /> thickness per layer. Deep repairs may be. Dry-stack the rest of the wall before
<br /> require applying product in multiple lifts or a I in the Crack-Resistant Surface
<br /> /'`-'� � layers after initial set between lifts pp Y g
<br /> (approximately 2-4 hours), product should Bonding Cement to both sides of the
<br /> �t,J � � wall. Apply product with a trowel in
<br /> Giaeoer o�esQ un�ipo4ea� 6Ures be firm, but not final set. Make sure to upward strokes, maintaining a uniform
<br /> � dampen the surFace area between thickness of at least '/e in. (3 mm). Do
<br /> ; applications of product. When troweling, not over-trowel.
<br /> �' be sure to ciean the surface of the trowel
<br /> S�f�t�6fasses Nentl MfMer lerel Tnwel
<br />
|