|
" - �r�r�a
<br /> � �����-�r
<br /> ,�,,� /�K��p► "�r�K " 1 2016 � . - ' �� �
<br /> G�. .... � ,r _ �
<br /> 6�LLEN��N��„e�������-�OF ORONa
<br /> PRODUCT DESCRIPTION contents of the bag in a wheel-barrow.
<br /> Akona�Crack-Resistant Surface Bonding bucket, mortar box, or mechanical mixer.
<br /> Cement is a specially-formulated, multi- Mix product thoroughly to achieve a stiff, —.�. $
<br /> use product. It can be used to build and Putty-like consistency. Avoid high speed , , �
<br /> restore retaining walls or block walls, mechanical mixing which can entrap air _ ` � ' � d � �
<br /> patch large vertical holes where into the mixture. If the product becomes ' � ' ' ,
<br /> non-sagging cement is a must, or repair firm before application, re-mix to proper 8u�sseestaresWa�s "
<br /> deteriorated stucco. Because it contains consistency. If required, add additional »;,,��. �� . �
<br /> special fibers it will not shrink, crack, or `Nater spanngly, up to a totai of 1'/z gal. :��;�, ����� . •�
<br /> (5.7 L)liquid per 50 Ib. (22.7 kg)powder. �-^k��•�-��•«�-'� � •
<br /> sag on a vertical repair. Provides ^���•-� '*- -'�
<br /> additional overall strength vs.
<br /> conventional concrete. Optional: For improved durability, �---
<br /> strength, and adhesion when applying � , . _�. , "`
<br /> YYHEN/YYHERE TO USE over previously coated and non-porous
<br /> surfaces it is recommended to use Akona a . � f _ � ,.
<br /> • Repair deteriorated concrete walis Concrete Bonding Additive in place of �.�`�.�..
<br /> . Patch deep vertical holes water(sold separately). Concrete Bonding
<br /> • Restore damaged concrete, masonry, Additive may be diluted by up to Ya with often with water and use a "light touch"
<br /> and stucco water, however, for extra difficult when finishing the surface. Do not over
<br /> • Bonds dry-stacked masonry walis restoration or waterproofing projects, it is trowel. Protect the surface from use until
<br /> recommended to be used at full strength. patch is completely hard and set. Clean
<br /> ADVANTAGES up with soap and warm water as soon as
<br /> . Moisture resistant APPLICATION appiication is completed.
<br /> • Glass fiber reinforced for durability Apply only to surfaces that are frost-free
<br /> . High strength and above 40°F (4°C) and below 100°F Bonding Dry-Stack Segmental
<br /> • Controls shrinkage, cracking, and (38°C) within 24 hours of application and Retaining Walis &Masonry Wails:
<br /> sagging on vertical repairs 72 hours thereafter. Dampen the wall • Footings or Foundations: The secret
<br /> • Just mix with water or a bonding surface prior to applying product with a to sound structure is a strong, level
<br /> additive and use water spray. If the wall becomes dry foundation. A level and properly aligned
<br /> before application of product, re-wet the footing makes stacking and troweling
<br /> AVAILABLE SIZE wall. The dampened walls are important in much easier. Footings must be built
<br /> • 50 Ib. (22.7 kg) bag (BOM#102614) establishing a strong band. below the frost line and should a be a
<br /> minimum of twice the thickness of the
<br /> �Y blocks used. Consult your local
<br /> COVERAGE � masonry supplier for information about
<br /> One 50 Ib. bag covers approximately 50 �� � footings and slab construction.
<br /> sq. ft. at'/8 in. (3 mm)thickness • Dry-stacking Masonry Units: Lay the
<br /> �- first course of masonry units in a full
<br /> SURFACE PREPARATION � ir'� bed of Crack-Resistant Surface
<br /> „�,,,. a �j Bonding Cement. Make sure this course
<br /> Read all directions before starting work. - g���� is straight and level. Dry-stack masonry
<br /> �.
<br /> Remove all loose or unsound materials. -- �` :_ ` units in a staggered or running bond
<br /> Thoroughly clean surface of dirt, dust, pattern for strength. As you place
<br /> grease, paint or other contaminants masonry units in position, slide it
<br /> before building or restoring walis. against the masonry units below to
<br /> PRE-WET SURFACE JUST PRIOR TO Patching or Filling Holes in Concrete/
<br /> APPLICATION OF PRODUCT. Masonry Wails &Stucco Repair: smooth out any roughness. Crack-
<br /> Resistant Surface Bonding Cement can
<br /> Crack-Resistant Surface Bonding Cement be used between masonry units to
<br /> MIXING is ideally suited for patching or filling holes maintain a level and properly aligned
<br /> in concrete or masonry walls, as well as..
<br /> Begin with approximately 1 gal. (3.8 L) of repairing cracks or filling openings in `Nall. The better you are in maintaining a
<br /> dean cool water per bag. Mix complete stucco walis. Apply up to YZ in. (1.3 cm) �evel and aligned wall, the stronger and
<br /> thickness per layer. Deep repairs may more attractive your finished wall will
<br /> require applying product in multiple lifts or be. Dry-stack the rest of the wall before
<br /> ��I la ers after initial set between lifts applying the Crack-Resistant Surface
<br /> �� � � , '� ' (approximately 2-4 hours), product should Bonding Cement to both sides of the
<br /> be firm, but not final set. Make sure to �✓all. Apply product with a trowel in
<br /> Cleane� Brush 9�oGino fiqF". Gioues upward strokes, maintaining a uniform
<br /> � � dampen the surface area between
<br /> �' �� applications of product. When troweling, thickness of at least '/e in. (3 mm). Do
<br /> � � be sure to clean the surface of the trowel not over-trowel.
<br /> SafetYGlasses NantlMiMer ieue� trowe�
<br />
|